2004 IRR - National Building Code of the Philippnes

September 13, 2017 | Author: Dico Gaanan | Category: Building Code, Fine (Penalty), Copyright, Demolition, Electrical Wiring
Share Embed Donate


Short Description

Download 2004 IRR - National Building Code of the Philippnes...

Description

(1) October 29, 2004

REVISED IMPLEMENTING RULES AND REGULATIONS OF THE NATIONAL BUILDING CODE OF THE PHILIPPINES (P.D. 1096)

Pursuant to the authority vested in the Secretary of the Department of Public Works and Highways (DPWH) under Chapter 2 of the National Building Code of the Philippines (PD 1096), the following Rules and Regulations are hereby promulgated and issued: RULE I General Provisions SECTION 101.

Title. —

These Rules shall be known and cited as the "Revised Implementing Rules and Regulations of the National Building Code of the Philippines (P.D. 1096)" and shall be referred to as the "IRR". TDCAIS

SECTION 102.

Declaration of Policy. —

It is hereby declared to be the policy of the State to safeguard life, health, property, and public welfare, consistent with the principles of sound environmental management and control; and to this end, make it the purpose of the Code to provide for all buildings and structures, a framework of minimum standards and requirements to regulate and control their location, site, design, quality of materials, construction, use, occupancy, and maintenance. SECTION 103. 1.

Copyright 2010

Scope and Application. —

The scope of this IRR shall cover the following disciplines: architectural, civil/structural, electrical, mechanical, sanitary, plumbing, and electronics. This shall also apply to the design, location, siting, construction, alteration, repair, conversion, use, occupancy, maintenance, moving, demolition of, and addition to public and private buildings and structures, except traditional

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

1

indigenous family dwellings, and those covered by Batas Pambansa Bilang 220 otherwise known as the "Economic and Socialized Housing Projects". 2.

Existing buildings or structures without appropriate building permits/certificates of occupancy may be legalized and issued the necessary permits and certificates, provided, they are made to conform to these rules and regulations. However, they shall be subject to the imposition of penalties, surcharges, fines and other appropriate measures. 2005iatdc

3.

The applicable and consistent provisions of the allied professional codes and other government agency codes as approved by the DPWH Secretary shall serve as the referral codes of PD 1096 and this IRR.

SECTION 104.

General Building Requirements. —

1.

All buildings or structures as well as accessory facilities thereto shall conform in all respects to the principles of safe construction and must be suited to the purpose for which they are designed.

2.

Buildings or structures intended to be used for the manufacture and/or production of any kind of article or product shall observe adequate environmental safeguards.

3.

Buildings or structures and all parts thereof as well as all facilities found therein shall be maintained in safe, sanitary and good working condition.

SECTION 105.

Site Requirements. —

The land or site upon which will be constructed any building or structure, or any ancillary or auxiliary facility thereto, shall be sanitary, hygienic or safe. In case of sites or buildings intended for use as human habitation or abode, the same shall be at a safe distance, as determined by competent authorities, from streams or bodies of water and/or sources of air considered to be polluted; from a volcano or volcanic site and/or any other building considered to be a potential source of fire or explosion. SECTION 106. 1. Copyright 2010

Definitions. —

For purposes of this IRR, the following definitions shall apply:

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

2

ADDITION — Any new construction which increases the height and/or floor area of existing buildings/structures. AGENCY OF THE GOVERNMENT — Refers to any of the various units of the government including a department, bureau, office, instrumentality, or government owned or controlled corporation. ALTERATION — Works in buildings/structures involving changes in the materials used, partitioning, location/size of openings, structural parts, existing utilities and equipment but does not increase the building height and/or floor area. APPLICATION FORMS — A preformatted prescribed application form duly accomplished and notarized by the respective design professional with validation matrices related to other building rules and regulations. APPLICANT/PERMITTEE — Any person, firm, partnership, corporation, head of government or private institution, organization of any character applying for the issuance of permits and certificates. BUILDING OFFICIAL — the Executive Officer of the OBO appointed by the Secretary. BUILDING PERMIT — A document issued by the Building Official (BO) to an owner/applicant to proceed with the construction, installation, addition, alteration, renovation, conversion, repair, moving, demolition or other work activity of a specific project/building/structure or portions thereof after the accompanying principal plans, specifications and other pertinent documents with the duly notarized application are found satisfactory and substantially conforming with the National Building Code of the Philippines (the Code) and its Implementing Rules and Regulations (IRR). CODE — PD 1096, otherwise known as the National Building Code of the Philippines. CONSTRUCTION — All on-site work done in the site preparation, excavation, foundation, assembly of all the components and installation of utilities, machineries and equipment of buildings/structures. CONVERSION — A change in the use or occupancy buildings/structures or any portion/s thereof, which has different requirements.

of

DEMOLITION — The systematic dismantling or destruction of a building/structure, in whole or in part. Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

3

DEPARTMENT — The Department of Public Works and Highways (DPWH). EXECUTIVE DIRECTOR — The Executive Officer or Head of the NBCDO. MOVING — The transfer of buildings/structures or portion/s thereof from original location or position to another, either within the same lot or to a different one. OFFICE OF THE BUILDING OFFICIAL (OBO) — The Office authorized to enforce the provisions of the Code and its IRR in the field as well as the enforcement of orders and decisions made pursuant thereto. REFERRAL CODES — The applicable provisions of the various agency and technical professional codes that are supplementary to the Code. RENOVATION — Any physical change made on buildings/structures to increase the value, quality, and/or to improve the aesthetic. REPAIR — Remedial work done on any damaged or deteriorated portion/s of building/structure to restore to its original condition. SECRETARY — Head or Chief Executive Officer of DPWH. STAFF — The personnel of the National Building Code Development Office (NBCDO). 2.

As used in this IRR, other words, terms and phrases enumerated in the Glossary hereof shall have the meaning or definition correspondingly provided therein. RULE II Administration and Enforcement

SECTION 201.

Responsibility for Administration and Enforcement. —

The administration and enforcement of the provisions of the Code and this IRR, including the imposition of penalties for administrative violations thereof, is hereby vested in the Secretary. SECTION 202.

Technical Staff. —

The National Building Code Development Office (NBCDO) created Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

4

through DPWH Department Order, shall serve as the technical staff of the Secretary. The functions thereof are as follows: 1.

Assist the Secretary in the administration and enforcement of the provisions of the Code and its IRR.

2.

Review, evaluate and take final action on various technical and legal problems forwarded to the Office of the Secretary. aCSEcA

3.

Conduct seminar/workshops on the Code, its IRR, and Batas Pambansa Blg. 344 (Accessibility Law).

4.

Undertake such other duties and tasks as may be assigned by the Secretary from time to time.

SECTION 203.

Copyright 2010

General Powers and Functions of the Secretary. —

1.

Formulate policies, plans, standards and guidelines on building design, construction, use, occupancy and maintenance, in accordance with the Code.

2.

Issue and promulgate additional rules and regulations in the form of Memorandum Circulars to implement the provisions of the Code and ensure compliance with policies, plans, standards and guidelines and issue office guidelines or Memorandum Circulars to guide the actions of the Building Official in the performance of his duties and responsibilities.

3.

Exercise appellate jurisdiction over the decisions and orders of the Building Official. The order or decision of the Secretary shall be final and executory subject only to review by the Office of the President of the Republic.

4.

Evaluate, review, approve and/or take final action on changes and/or amendments to existing Referral Codes as well as on the incorporation of other referral codes, which are not yet expressly made supplementary to the Code and its IRR.

5.

Prescribe and impose the amount of fees and other charges as may be deemed necessary that the Building Official shall collect in connection with the performance of regulatory functions.

6.

Appoint a Building Official, separate and distinct from the

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

5

Office of the City/Municipal Engineers in all Cities and Municipalities. SECTION 204.

Professional and Technical Assistance. —

The Secretary may secure professional, technical, scientific and other services including testing laboratories and facilities from other agencies of the National Government when deemed necessary. He may also engage and compensate within available appropriations, such number of consultants, experts and advisers on full or part-time basis, as may be necessary, coming from the government or private business, entities or associations to carry out the provisions of the Code and this IRR. SECTION 205.

Building Officials. —

Except as otherwise provided herein, the Building Official shall be responsible for carrying out the provisions of the Code in the field as well as the enforcement of orders and decisions made pursuant thereto. All Building Officials appointed or designated other than by the Secretary, shall continue to act as the Building Official until such time that the Secretary appoints the Building Official. Offices of the Building Officials already established, separate and distinct from the office of the City/Municipal Engineers in cities and municipalities may continue to exist until such time that a regular office is created. (Fig. II.1.) SECTION 206.

Qualifications of Building Officials. —

No person shall be appointed as Building Official unless he possesses the following qualifications:

Copyright 2010

1.

A Filipino citizen and of good moral character.

2.

A duly registered architect or civil engineer.

3.

A member of good standing of a duly accredited organization of his profession for not less than five (5) years endorsed or recommended by the accredited professional organization.

4.

Has at least five (5) years of diversified and professional experience in building design and construction.

5.

Has attended and successfully completed a seminar workshop on PD 1096 and its IRR conducted by the DPWH.

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

6

SECTION 207.

Duties of the Building Official. —

The Building Official shall have the following duties: 1.

Be primarily responsible for the enforcement of the provisions of the Code and its IRR, as well as circulars, memoranda, opinions and decisions/orders issued pursuant thereto. His actions shall always be guided by appropriate orders/directives from the Secretary.

2.

Have overall administrative control and/or supervision over all works pertinent to buildings/structures in his area of responsibility and shall be charged with the processing of all permit applications and certificates as well as the issuance of the same.

3.

Ensure that all changes, modifications, and alterations in the design plans during the construction phase shall not start until the modified design plan has been evaluated and the necessary amendatory permit issued. THaDAE

4.

Copyright 2010

Undertake annual inspections of all buildings/structures and keep an up-to-date record of their status.

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

7

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

8

Figure II.1. 5.

Copyright 2010

Upon complaint or motu proprio and after due notice/s and hearing, initiate action towards: a.

Non-issuance, suspension, revocation and/or invalidation of a building permit or certificate of occupancy;

b.

Issuance of work stoppage order, or an order for discontinuance of the use or occupancy of the building/structure or portion thereof;

c.

Declaration of a building/structure as ruinous or

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

9

dangerous; and/or d.

The imposition of appropriate fines/penalties.

6.

Submit a quarterly situational report to the Secretary through the NBCDO, on the status of all existing, on-going, and proposed public as well as private building/structure activities. (See Communication Flow Chart, Fig. II.2.)

7.

Undertake such other duties and tasks as may be assigned by the Secretary from time to time.

SECTION 208.

Fees. —

1.

The Secretary, thru Memorandum Circulars, shall prescribe the rates of fees and formulate guidelines in the imposition and collection of fees.

2.

Subject to existing budgetary, accounting and auditing rules and regulations, the Building Official shall retain not more than 20% of the income/collection derived from permit fees and other charges for the operating expenses of his office. The remainder of 100% shall accrue to the general fund of the respective city/municipality.

3.

Every Building Official shall keep a permanent record and accurate account of all fees and other charges fixed and authorized to be collected and received.

SECTION 209.

Exemption. —

Public buildings and traditional indigenous family dwellings shall be exempt from payment of building permit fees. As used in the Code, the term "traditional indigenous family dwelling" means a dwelling intended for the use and occupancy by the family of the owner only and constructed of native materials such as bamboo, nipa, logs, or lumber, the total cost of which does not exceed fifteen thousand pesos (P15,000.00). SECTION 210.

Use of Income from Fees. —

The procedure for the proper reporting and recording of collections and disbursements of the funds of the General Fund Special Account 151 of the Office of the Secretary of the Department of Public Works and Highways (DPWH) is Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

10

hereby prescribed. 1.

Recording of Collections a.

Every Building Official shall keep a permanent record and accurate account of all fees and other charges fixed and authorized to be collected by him. TcHCIS

Copyright 2010

b.

The Order of Payment issued by the Building Official shall show the breakdown of the total collections Indicating the share of the local government concerned — 80% and the share of the national government — 20%.

c.

Every Building Official shall keep a separate record

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

11

from the DPWH Central Office of all allotments (Special Allotment Release Order (SARO) and Notice of Cash Allocation (NCA), or Funding Checks), received by him out of budgeted amounts released by the Department of Budget and Management (DBM). The funds shall cover all the necessary operating expenses of the OBO, including the purchase of equipment, supplies and materials, traveling expenses, obligation expenses and sheriffs' fees and payment of other prior years' obligations not adequately funded, subject to existing budgetary and auditing rules and regulations. d. 2.

He shall render the reports required under the Centralized Accounting System.

Disposition of Collections a.

The collection shall be made by the Local Treasurer, and the Official Receipt shall show the breakdown of the total collections indicating the share of the local government concerned — 80% and the share of the national government — 20%.

b.

Subject to existing budgetary, accounting and auditing rules and regulations, the Local Treasurer shall remit to the Bureau of the Treasury, the 20% of his collection. The remaining 80% shall be deposited with the Authorized Government Depository Bank (AGDB) for the account of the Local Government and shall accrue to the general funds of the City or Municipality concerned.

c.

Pursuant to Sec. 21, Volume I of the New Government Accounting System (NGAS) Manual as provided under COA Circular No. 2001-004 dated October 30, 2001, the Local Treasurer thru his collecting officer or cashier shall deposit the 80% share of collections to the AGDB for the account of the Local Government concerned. He shall remit the 20% of the collections to the Bureau of the Treasury thru any AGDB branch nearest the locality to the credit of the Department of Public Works and Highways (DPWH), Office of the Secretary with Code No. B5702 and Special Account No. 151. HAEDCT

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

12

d.

e.

Distribution of validated remittance advices and deposit slips of the 20% collections thru any Authorized Government Depository Bank shall be in accordance with COA Circular 2001-004, to wit: Original

-

to be retained by the bank branch.

Duplicate

-

to be submitted by the Local Treasurer to the OBO.

Triplicate

-

to be retained by the bank branch for submission to the Provincial Treasury Fiscal Examiner assigned to the province where the bank is located.

Quadruplicate

-

to be returned to the Local Treasurer for submission to the DPWH-Central Office (CO) Chief Accountant with his monthly report of collections.

Quintuplicate

-

to be returned to the Local Treasurer for submission to the Field/Local Auditor.

The Local Treasurers and the Treasury Vault/Bank Auditor shall have the following responsibilities: i. Local Treasurer. Since the distribution of copies of the validated remittance advices and deposit slips for the Agency/Field Auditor of the Local Treasurers shall be undertaken by the National/Treasury/Bank Branch thru its Treasury Vault Auditor/Bank Auditor, all Local Treasurers shall indicate on the face of the remittance advice, the name and office address of their respective Agency/Field Auditors to facilitate matters. TCDHaE

ii. Treasury Vault/Bank Auditor. Upon receipt of the validated remittance advices, the Treasury Vault Auditor/Bank Auditor shall confirm and transmit said remittance advices every end of the week to the corresponding agency/field auditor of the Local Treasurer concerned. In cases where there is no bank auditor assigned in a particular locality, confirmation shall be undertaken by the officer designated by the Head of the Bank branch. Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

13

f.

Reporting of Collections and Deposits At the close of each business day, the collecting officers (Local Treasurers) shall accomplish the Report of Collections and Deposits (RCD) in accordance with the NGAS Manual. The reports shall be prepared by the Local Treasurer in five copies, distributed as follows after verification by the field auditor: Original

-

to the DPWH-CO Auditor (thru the DPWH-CO Accountant for recording).

Duplicate (with duplicate official - to the Field/Local Auditor receipts and validated quintuplicate for final custody. remittance advices) Triplicate (with validated quadruplicate remittance advices)

to the DPWH-CO Accountant (for posting to the corresponding subsidiary ledgers).

Quadruplicate

-

to be retained by the Local Treasurer.

Quintuplicate

-

local office accounting file.

The Local Treasurer shall certify all the copies of the report and submit the first three (3) copies to his Field Auditor within three (3) days after the end of the month for audit. The Field Auditor shall verify the report, cross-check the remittances indicated therein against the quintuplicate copies of remittance advices he receives/received from the Bank Auditor and indicate his certification thereon and finally submits the original and triplicate copies thereof to the DPWH-CO Auditor thru the DPWH-CO Chief Accountant within five (5) days from date of receipt from the Local Treasurer. CIaASH

g.

Crediting of Accounts of Local Treasurer In the monthly report of collections, specifically at the back thereof, is a statement of account current showing the accountability of the Local Treasurer. The DPWH-CO Chief Accountant shall cross-check the validated quadruplicate remittance advices attached to the duplicate copy of the monthly

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

14

report of collections against the remittances made by the Local Treasurer with the National Treasury or any of its authorized depository banks as appearing in the statement of account current. After the cross-checking, and in the absence of any discrepancy, the DPWH-CO Chief Accountant shall credit the account of the Local Treasurer even without the monthly abstract of remittances from the National Treasury. h.

Safeguards i. Upon receipt of the monthly abstract of remittances from the National Treasury, the remittances appearing therein shall be counter checked by the DPWH-CO Chief Accountant against the credits already given the collecting officers concerned and any discrepancies discovered in the process shall be verified and adjusted immediately. ii. In case of retirement or resignation by the Local Treasurers, their clearances shall be held in abeyance until their remittances have been fully cleared by the National Treasury.

i.

Centralized Accounting System i. A centralized accounting system shall be maintained in the Office of the DPWH Secretary. Said office shall set up and maintain a separate set of books of accounts to be used solely for transactions pertaining to the implementation of the provisions of the National Building Code and its Implementing Rules and Regulations. cCESaH

ii. Upon receipt of the SARO and the corresponding NCA, the Office of the DPWH Secretary shall in turn allocate the same together with the NCA or Funding Check to the Building Officials, and at the same time obligate the allotment for the amount of expenditures. iii. All deputized disbursing officers shall render the following reports: Report of Checks Issued together with duplicate copies Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

15

of checks issued for submission to the Treasury Provincial Fiscal Examiner in the region. Report of Checks Issued as required by the NGAS for entry in the Checks Disbursement Journal by DPWH-CO Chief Accountant. iv. The Department Chief Accountant shall adjust obligations quarterly to actual liquidations as required. HSIaAT

v. Deputized disbursing officers shall keep a record to control NCA/Funding Check separate from other funds in his custody. vi. Deputized disbursing officers shall prepare other statements or reports as may be required from time to time by the proper authorities. vii. The Deputized Disbursing Officer (DDO) shall render a monthly report of accountability for checks issued during the month and the balance at the end of the month. Copies of said report shall be distributed as follows: Original

-

to the Treasury Provincial Fiscal Examiner (Cash Operation Service)

Duplicate

-

to the DPWH-CO Chief Accountant

Triplicate

-

to the Auditor, DPWH-CO

Quadruplicate

-

Field Auditor

Quintuplicate

-

File of Disbursing Officer

viii. The deputized disbursing officer authorized to requisition blank Modified Disbursement System (MDS) or Commercial checks shall prepare and submit requisition and issue voucher, and the Invoice and Receipt of Accountable Forms which shall be distributed as follows: Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

16

j.

Original

-

Treasury Provincial Fiscal Examiner

Duplicate

-

Cash Operations Service, Bureau of the Treasury

Triplicate

-

COA Auditor of the DDO's Agency

Quadruplicate

-

Accounting Unit of DDO

Quintuplicate

-

DDO file

Sextuplicate

-

Office of the Provincial/City Auditor Concerned

Turnover of Accountability i. In case of change, transfer, resignation or retirement from the service of the Building Official, an inventory of all money and property accountabilities shall be taken jointly by the outgoing and incoming Building Official and a receipt passed on the basis of such inventory. Such inventory shall be certified as accurate by the said officers, witnessed by the local auditor thereat. ii. The preceding procedure shall also apply to a deputized disbursing officer other than the Building Official with respect to money and property accountabilities in his custody. iii. Application for clearance of the Building Official and other deputized disbursing officers shall be coursed to the Office of the DPWH Secretary, to check their unpaid obligations with the OBO.

k.

Other Provisions i. Compensation of consultants, experts and advisers whose services were secured shall be funded from the 20% Income derived from the building permit fees and other charges. ACaTIc

ii. Copyright 2010

CD Technologies Asia, Inc.

Any circular/s that may subsequently be issued by

Philippine Laws Premium Edition 2009

17

the proper authorities revoking or amending provisions or certain portions of circular/s incorporated in the above rules and regulations shall automatically revoke or amend such corresponding portions that are inconsistent therewith. SECTION 211.

Implementing Rules and Regulations. —

In the implementation of the provisions of the Code and its IRR, the Secretary shall formulate necessary rules and regulations and adopt design and construction standards and criteria for buildings and other structures. Such standards, rules and regulations shall take effect after their publication once a week for three consecutive weeks in a newspaper of general circulation. DASEac

SECTION 212. 1.

Administrative Fines. —

Imposition of Administrative Fines a.

The Secretary or his duly authorized representative may prescribe and impose fines not exceeding ten thousand pesos (P10,000.00) in the following cases, subject to the terms and procedures as hereunder provided: i. Erecting, constructing, altering, repairing, moving, converting, installing or demolishing a private or public building/structure if without building/demolition permit. ii. Making any alteration, addition, conversion or repair in any building/structure/appurtenances thereto constructed or installed before the adoption of the Code, whether public or, private, without a permit. iii. Unauthorized chance, modification or alteration during the construction in the duly submitted plans and specifications on which the building permit is based. iv. Non-compliance with the work stoppage order or notice and/or orders to effect necessary correction In plans and specifications found defective. v. Non-compliance with order to demolish building/structure declared to be nuisance, ruinous or dangerous.

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

18

vi. Use or occupancy of a building/structure without Certificate of Occupancy/Use even if constructed under a valid building permit. vii. Change in the existing use or occupancy classification of a building/structure or portion thereof without the corresponding Certificate of Change of Use. viii. Failure to post or display the certificate of occupancy/use/operation in a conspicuous place on the premises of the building/structure/appurtenances. ix. Change in the type of construction of any building/structure without an amendatory permit. b.

2.

In addition to the imposed penalty, the owner shall correct/remove his violations of the provisions of the Code.

Determination of Amount of Fines a.

In the determination of the amount of fines to be imposed, violations shall be classified as follows: i.

Light Violations (a) Failure to post Occupancy/Use/Operation.

Certificate

of

(b) Failure to post Building Permit construction information sign. (c) Failure to provide or install appropriate safety measures for the protection of workers, inspectors, visitors, immediate neighbors and pedestrians. ii.

Less Grave Violations (a) Non-compliance with the work stoppage order for the alteration/addition/conversion/repair without permit. (b) Use or occupancy of building/structure

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

19

without appropriate Occupancy/Use/Operation. iii.

Certificate

of

Grave Violations (a) Unauthorized change, modification or alteration during construction in the duly submitted plans and specifications on which the building permit is based. (b) Unauthorized change in type of construction from more fire-resistive to less fire-resistive. (c) Non-compliance with order to abate or demolish. (d) Non-compliance with work stoppage order for construction/demolition without permit. (e) Change in the existing use or occupancy without Certificate of Change of Occupancy/Use/Operation. IHCSET

(f) Excavations left open without any work being done in the site for more than one hundred twenty (120) days. b.

Amount of Fines The following amount of fines for violations of the Code and this IRR is hereby prescribed:

c.

Light Violations

-

P5,000.00

Less Grave Violations

-

P8,000.00

Grave Violations

-

P10,000.00

Penalty i. Without prejudice to the provisions of the preceding Sections, the Building Official is hereby also authorized to impose a penalty or surcharge in the following cases in such amount and in the manner as hereunder fixed and determined:

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

20

For constructing, installing, repairing, altering or causing any change in the occupancy/use of any building/structure or part thereof or appurtenances thereto without any permit, there shall be imposed a surcharge of 100% of the building fees; Provided, that when the work in the building/structure is started pending issuance of the Building Permit by the Building Office, the amount of the surcharge shall be according to the following: Excavation for foundation building permit fees Construction of foundation (including pile driving and laying of reinforcing bars) building permit fees Construction of superstructure up to 2.00 meters above established grade building permit fees Construction of superstructure above 2.00 meters building permit fees

2.

- 10% of the

- 25% of the

- 50% of the

- 100% of the

For failure to pay the annual inspection fee within thirty (30) days from the prescribed date, a surcharge of 25% of the inspection fee shall be imposed.

SECTION 213.

Penal Provisions. —

It shall be unlawful for any person, firm or corporation, to erect, construct, enlarge, alter, repair, move, improve, remove, convert, demolish, equip, use, occupy, or maintain any building or structure or cause the same to be done contrary to or in violation of any provision of the Code. Any person, firm or corporation who shall violate any of the provisions of the Code and/or commit any act hereby declared to be unlawful shall upon conviction, be punished by a fine of not more than twenty thousand pesos or by Imprisonment of not more than two years or by both such fine and Imprisonment; Provided, that in the case of a corporation firm, partnership or association, the penalty shall be imposed upon its officials responsible for such violation and in Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

21

case the guilty party is an alien, he shall immediately be deported after payment of the fine and/or service of his sentence. SECTION 214.

Dangerous and Ruinous Buildings or Structures. —

Dangerous buildings are those which are herein declared as such or are structurally unsafe or not provided with safe egress, or which constitute a fire hazard, or are otherwise dangerous to human life, or which in relation to existing use, constitute a hazard to safety or health or public welfare because of inadequate maintenance, dilapidation, obsolescence, or abandonment; or which otherwise contribute to the pollution of the site or the community to an Intolerable degree. SECTION 215.

Abatement of Dangerous Buildings. —

When any building or structure is found or declared to be dangerous or ruinous, the Building Official shall order its repair, vacation or demolition depending upon the degree of danger to life, health, or safety. This is without prejudice to further action that may be taken under the provisions of Articles 482 and 694 to 707 of the Civil Code of the Philippines. The condition or defects that render any building/structure dangerous or ruinous are as follows: (See Procedure for Abatement/Demolition of Dangerous/Ruinous Buildings/Structures at the end of this Rule) 1.

Structural Hazards a.

Whenever any building/structure or portion thereof has been damaged by fire, earthquake, wind, flood, or by any other cause to such an extent that the structural strength or stability thereof is materially less than it was before the catastrophe and is less than the minimum requirements of the National Structural Code of the Philippines (NSCP) for new buildings of similar structure, purpose or location.

b.

Whenever any portion or member or appurtenances thereof is likely to fall, or to become detached or dislodged or to collapse and thereby injure persons or damage property. DTSIEc

c.

Copyright 2010

Whenever any portion of a building/structure or any member, appurtenance or ornamentation on the exterior thereof is not of sufficient strength or stability, or is not anchored, attached or fastened in place so as to be

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

22

capable of resisting a wind pressure of one-half of that specified in the NSCP for such type of buildings. d.

Whenever any portion thereof has been wrecked, warped, buckled or settled to such an extent that the walls or other structural portions have materially less resistance to wind or earthquake than is required in the case of similar new construction.

e.

Whenever the building/structure or any portion thereof, because of: (1) dilapidation, deterioration or decay; (2) faulty construction; (3) the removal, movement or instability of any portion of the ground necessary for the purpose of supporting such building; (4) the deterioration, decay or inadequacy of its foundation; or (5) any other cause, is likely to partially or totally collapse. caIACE

Copyright 2010

f.

Whenever the exterior walls or other vertical structural member lean or buckle to such an extent that a plumb line passing through the center of gravity does not fall inside the middle one-third of the base.

g.

Whenever the building/structure, exclusive of the foundation, shows 33% or more damage or deterioration of its supporting member or members, or 50% damage or deterioration of its non-supporting members, enclosing or outside walls or coverings.

h.

Whenever the building/structure has been so damaged by fire, wind, earthquake or flood, or has become so dilapidated or deteriorated as to become: (1) an attractive nuisance to public; (2) a harbor for vagrants, criminals or immoral persons; or (3) a resort for purposes of committing unlawful or immoral acts.

i.

Whenever the building/structure which, whether or not erected in accordance with all applicable laws or ordinances, has in any nonsupporting part, member or portion, less than 50% or in any supporting part, member or portion less than 66% of the: (1) strength; (2) fire-resisting qualities or characteristics; (3) weather-resisting qualities or characteristics required by

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

23

law in the case of a newly constructed building of like area, height and occupancy in the same location. j.

2.

3.

Whenever any portion of a building/structure remains on the site after its demolition or whenever any building/structure or portion thereof is abandoned for a period in excess of twelve (12) months so as to make it a nuisance or hazard to the public.

Fire Hazards a.

Any building/structure be portion thereof, device, apparatus, equipment material, or vegetation which may cause fire or explosion, or provide a ready fuel or augment the speed and intensity of fire or explosion arising from any cause.

b.

All buildings/structures or portions thereof not provided with the required fire-resistive or fire-protective construction or fire-extinguishing system or equipment.

c.

Whenever any door, aisle, passageway, stairway, or other means of exit is not of sufficient width or size, or is not so arranged as to provide safe and adequate means of exit in case of fire and panic.

d.

Whenever any building/structure, because of obsolescence, dilapidated condition, deterioration, damaged, inadequate exits, lack of sufficient fire-resistive construction, hazardous electric wiring, gas connections or heating apparatus, or other cause, in violation of the Fire Code of the Philippines (PD 1185).

Unsafe Electrical Wiring a.

All wiring systems or installations which do not conform to the rules and regulations embodied in the latest Philippine Electrical Code.

b.

Inadequately maintained or improperly used electrical wirings, outlets, devices and/or equipment. aCHcIE

4. Copyright 2010

Unsafe Mechanical Installation

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

24

5.

6.

Copyright 2010

a.

Mechanical systems or installations which do not conform to the rules and regulations embodied in the Philippine Mechanical Code.

b.

Inadequately maintained or Improperly used mechanical outlets, devices and/or equipment.

c.

Lack of or improper operation of required ventilating equipment or airconditioning systems.

d.

Improperly installed or lack of protection and safety provisions on steam; gas and fuel supply lines.

Inadequate Sanitation/Plumbing and Health Facilities a.

All sanitation and plumbing systems or installations which do not conform to the rules and regulations embodied in the Code on Sanitation of the Philippines and the Revised National Plumbing Code.

b.

Inadequately maintained or improperly used sanitation and plumbing facilities.

c.

Infestation of insects, vermin or rodents and lack of adequate control for the same.

d.

Lack of adequate garbage and rubbish storage and removal or disposal facilities.

e.

Source of pollution.

Architectural Deficiency a.

All buildings/structures or portion thereof used or occupied for purposes other than their intended uses.

b.

Improper/Unauthorized Occupancy/Location.

c.

Insufficient amount of natural light and ventilation due to Inadequate open spaces such as courts and yards as required.

d.

Inadequate sizes of rooms and space dimensions and window openings.

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

25

e.

Dilapidated, blighted and other unpresentable buildings/structures against generally accepted aesthetic standards. TcEDHa

SECTION 216.

Other Remedies. —

The rights, actions and remedies provided in the Code and in the IRR shall be in addition to any and all other rights of action and remedies that may be available under; existing laws. PROCEDURE FOR ABATEMENT/DEMOLITION OF DANGEROUS/RUINOUS BUILDINGS/STRUCTURES

Copyright 2010

1.

There must be a finding or declaration by the Building Official that the building/structure is a nuisance, ruinous or dangerous.

2.

Written notice or advice shall be served upon the owner and occupant/s of such finding or declaration giving him at least fifteen (15) days within which to vacate or cause to be vacated, repaired, renovated, demolished and removed as the case may be, the nuisance, ruinous or dangerous building/structure or any part or portion thereof.

3.

Within the fifteen (15) day period, the owner may, if he so desires, appeal to the Secretary the finding or declaration of the Building Official and ask that a reinspection or re-investigation of the building/structure be made.

4.

In case the owner should ask the Building Official for a reconsideration on his order, same shall be given not more than not more than fifteen (15) days within which to render his final decision appealable to the Office of the Secretary.

5.

If the appeal is meritorious, the Secretary may designate a competent representative/s other than the Building Official to undertake the re-inspection or re-investigation of the building/structure. The representative/s so designated shall make or complete his/their report/s within the period of thirty (30) days from the date of termination of re-inspection or re-investigation.

6.

If after re-inspection, the finding is the same as the original one, the Secretary through the Building Official shall notify the

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

26

owner, giving him not more than fifteen (15) days from receipt of notice with affirmed finding to vacate or cause to be vacated and make necessary, repair, renovation, demolition and removal of the subject building/structure or parts thereof, as the case may be.

Copyright 2010

7.

If the Building Official has determined that the building/structure must be repaired or renovated, the Order to be issued shall require that all necessary permits therefor be secured and the work be commenced physically within such reasonable time as may be determined by the Building Official.

8.

If the Building Official has determined that the building/structure must be demolished, the Order shall require that the building/structure be vacated within fifteen (15) days from the date of receipt of the Order; that all required permits be secured therefor within the same fifteen (15) days from the date of the Order, and that the demolition be completed within such reasonable time as may be determined by the Building Official.

9.

The decision of the Secretary on the appeal shall be final.

10.

Upon failure of the owner to comply with the Order of the Building Official or of the Secretary, in case of appeal, to repair, renovate, demolish and remove the building/structure or any part thereof after fifteen (15) days from the date of receipt the Order, the Building Official shall cause the building or structure to be repaired, renovated, demolished and removed, partly or wholly, as the case may be, with all expenses therefor chargeable to the owner.

11.

The building/structure as repaired or in case of demolition, the building materials gathered after the demolition thereof shall be held by the OBO until full reimbursement of the cost of repair, renovation, demolition and removal is made by the owner which, in no case, shall extend beyond thirty (30) days from the date of completion of the repair, renovation, demolition and removal. After such period, said building materials of the building thus repaired, renovated or removed shall be sold at public auction to satisfy the claim of the OBO. Any amount in excess of the claim of the government realized from the sale of the building and/or building materials shall be delivered to the

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

ADSTCI

27

owner. 12.

The procedures, actions and remedies herein are without prejudice to further action that may be taken by the Building Official against the owner/occupants of the building/structure found or declared to be nuisance/s, dangerous, and/or ruinous under the provisions of Articles 482 and 694 to 707 of the Civil Code of the Philippines. RULE III Permits and Inspection

SECTION 301.

Building Permits. —

1.

No person, firm or corporation, including any agency or instrumentality of the government shall construct, alter, repair, convert, use, occupy, move, demolish and add any building/structure or any portion thereof or cause the same to be done, without first obtaining a building permit therefor from the Building Official assigned in the place where the subject building/structure is located or to be done. The prescribed application for building permit form (NBC Form B-01) shall be used by all applicants.

2.

Permits supplementary to a Building Permit shall be applied for and issued by the Building Official. These include Ancillary and the Accessory Permits. a.

Ancillary Permits The Ancillary Permits duly signed and sealed by the corresponding professionals and the plans and specifications shall be submitted together with the duly notarized application for Building Permit. The Building Permit is null and void if not accompanied by the Ancillary Permits. The prescribed Ancillary and other Accessory Permits/forms shall likewise be used whenever applicable. The Ancillary Permits are the following:

Copyright 2010

CD Technologies Asia, Inc.

i.

Architectural Permit

ii.

Civil/Structural Permit

iii.

Electrical Permit

Philippine Laws Premium Edition 2009

28

iv.

Mechanical Permit

v.

Sanitary Permit

vi.

Plumbing Permit

vii. Electronics Permit b.

Accessory Permits i. Accessory Permits are issued by the Building Official for accessory parts of the project with very special functions or use which are indicated in the plans and specifications that accompany the building permit application. These may include among others: bank and records vaults; swimming pools; firewalls separate from the building/structure; towers; silos; smokestacks; chimneys; commercial/industrial fixed ovens; industrial kilns/furnaces; water/waste treatment tanks, septic vaults; concrete and steel tanks; booths, kiosks and stages; and tombs, mausoleums and niches. ii. Accessory Permits are issued by the Building Official for activities being undertaken prior to or during the processing of the building permit. The coverage is spelled out in the accessory permit form including the expiry period. These shall be signed by the concerned owner/applicant and by the concerned professionals. These permits include among others, ground preparation and excavation, encroachment of foundation to public area, fencing, for fence not exceeding 1.80 meters high, sidewalk construction, temporary sidewalk enclosure and occupancy, erection of scaffolding, erecting, repair, removal of sign; and demolition.

3.

Exemption From Building Permits A building permit shall not be required for the following minor constructions and repairs, provided these shall not violate any provision of the Code and this IRR. a.

Minor Constructions i.

Copyright 2010

CD Technologies Asia, Inc.

Sheds,

outhouses,

Philippine Laws Premium Edition 2009

greenhouses,

children's 29

playhouses, aviaries poultry houses and the like, not exceeding 6.00 sq. meters in total area, provided they are completely detached from any other building and are intended only for the private use of the owner. SHcDAI

ii. Addition of open terraces or patios resting directly on the ground, not exceeding 20.00 sq. meters in total floor area, exclusively for the private use of the owner. iii.

Installation of window grilles.

iv. Garden pools for the habitation of water plants and/or aquarium fish not exceeding 500 millimeters in depth and exclusively for private use. v. Garden masonry walls other than party walls not exceeding 1.20 meters in height, footpaths, residential garden walks and/or driveways. b.

Repair Works i. Repair works not affecting or involving any structural member, such as replacement of deteriorated roofing sheets or tiles, gutters, downspouts, fascias, ceilings and/or sidings. ii. Repair and/or replacement of non load-bearing partition walls. iii. Repair and/or replacement of any interior portion or a house not involving addition or alteration. iv. Repair and/or replacement work of doors and windows. v.

Repair and/or replacement work of flooring.

vi.

Repair of perimeter fence and walls.

vii. Repair and/or replacement of plumbing fixtures, fittings or pipings, such as toilet bowls, sinks, lavatories, urinals, bidets, pipes, faucets, valves for single detached dwellings and duplexes.

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

30

SECTION 302.

Application for Permits. —

1.

Any person desiring to obtain a building permit and any ancillary/accessory permit/s together with a Building Permit shall file application/s therefor on the prescribed application forms.

2.

Together with the accomplished prescribed application form/s, the following shall be submitted to the OBO: a.

In case the applicant is the registered owner of the lot: i. Certified true copy of OCT/TCT, on file with the Registry of Deeds, aEDCAH

b.

3.

Copyright 2010

ii.

Tax Declaration, and

iii.

Current Real Property Tax Receipt.

In case the applicant is not the registered owner of the lot, in addition to the above, duly notarized copy of the Contract of Lease, or Deed of Absolute Sale.

Five (5) sets of survey plans, design plans, specifications and other documents prepared, signed and sealed over the printed names of the duly licensed and registered professionals (Figs. III.1. and III.2.): a.

Geodetic Engineer, in case of lot survey plans;

b.

Architect, in case of architectural documents; in case of architectural interior/interior design documents, either an architect or interior designer may sign;

c.

Civil Engineer, in case of civil/structural documents;

d.

Professional Electrical Engineer, in case of electrical documents;

e.

Professional Mechanical Engineer, in case of mechanical documents;

f.

Sanitary Engineer, in case of sanitary documents;

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

31

4.

g.

Master Plumber, in case of plumbing documents;

h.

Electronics Engineer, in case of electronics documents.

Architectural Documents a.

Architectural Plans/Drawings i. Vicinity Map/Location Plan within a 2.00 kilometer radius for commercial, Industrial, and Institutional complex and within a half-kilometer radius for residential buildings, at any convenient scale showing prominent landmarks or major thoroughfares for easy reference. ii. Site Development Plan showing technical description, boundaries, orientation and position of proposed building/structure in relation to the lot, existing or proposed access road and driveways and existing public utilities/services. Existing buildings within and adjoining the lot shall be hatched and stances between the proposed and existing buildings shall be indicated. iii. Perspective drawn at a convenient scale and taken from a vantage point (bird's eye view or eye level). iv. Floor Plans drawn to scale of not less than 1:100 showing: gridlines, complete identification of rooms or functional spaces. v. Elevations, at least four (4), same scale as floor plans showing: gridlines; natural round to finish grade elevations; floor to floor heights; door and window marks, type of material and exterior finishes; adjoining existing structure/s, if any, shown in single hatched lines. vi. Sections, at least two (2), showing: gridlines; natural ground and finish levels; outline of cut and visible structural parts; doors and windows properly labeled reflecting the direction of opening; partitions; built-in cabinets, etc.; identification of rooms and functional spaces cut by section lines. vii. Reflected ceiling plan showing: design, location,

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

32

finishes and specifications of materials, lighting fixtures, diffusers, decorations, air conditioning exhaust and return grills, sprinkler nozzles, if any, at scale of at least 1:100.

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

33

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

34

MODEL TITLE BLOCK FOR BUILDING PLANS/CONSTRUCTION DRAWINGS Figure III.2 viii. Details, in the form of plans, elevations/sections: a)

Accessible ramps

b)

Accessible stairs

c)

Accessible lifts/elevators

(d) Accessible walkways

IDaEHS

entrances,

corridors

and

(e) Accessible functional areas/comfort rooms (f)

Accessible switches, controls

(g) Accessible drinking fountains (h) Accessible public telephone booths (i) Accessible audio visual and automatic alarm system (j) Accessible access symbols and directional signs (k) Reserved parking for disabled persons (l) Typical wall/bay sections from ground to roof (m) Stairs, interior and exterior (n) Fire escapes/exits (o) Built-in furniture

cabinets,

counters

and

fixed

(p) All types of partitions ix. Copyright 2010

CD Technologies Asia, Inc.

Schedule of Doors and Windows showing their

Philippine Laws Premium Edition 2009

35

types, designations/marks, dimensions, materials, and number of sets. x. Schedule of Finishes, showing in graphic form: surface finishes specified for floors, ceilings, walls and baseboard trims for all building spaces per floor level. xi. b.

Details of other major Architectural Elements.

Architectural Interiors/Interior Design i.

Space Plan/s or layout/s of architectural interior/s.

ii.

Architectural interior perspective/s.

iii.

Furniture/furnishing/equipment/process layout/s.

iv.

Access plan/s, parking plan/s and the like.

v. Detail design of major architectural interior elements. vi. Plan and layout of interior, wall partitions, furnishing, furniture, equipment/appliances at a scale of at least 1:100. vii. Interior wall elevations showing: finishes, switches, doors and convenience outlets, cross window sections with interior perspective as viewed from the main entrance at scale of at least 1:100. viii. Floor/ceiling/wall patterns and finishing details.

c.

ix.

List of materials used.

x.

Cost Estimates.

Plans and specific locations of all accessibility facilities of scale of at least 1:100. STIcaE

d.

Copyright 2010

Detailed design of all such accessibility facilities outside and around buildings/structures including parking areas, and their safety requirements all at scale of 1:50 or any convenient scale.

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

36

e.

Fire Safety Documents i. Layout plan of each floor indicating the fire evacuation route to safe dispersal areas, standpipes with fire hose, fire extinguishers, first aid kits/cabinets, fire alarm, fire operations room, emergency lights, signs, etc. ii. Details of windows, fire exits with grilled windows and ladders. iii. Details of fire-resistive construction of enclosures for vertical openings. iv. Details of fire-resistive construction materials and interior decorative materials with fire-resistive/fire-retardant/fire-spread ratings v.

f. 5.

Other Related Documents

Other related documents

Civil/Structural Documents a.

Site Development Plan Site Development Plan showing technical description, boundaries, orientation and position of proposed non-architectural horizontal structure such as: sewerage treatment plan (STP), silos, elevated tanks, towers, fences, etc. building/structure in relation to the lot, existing or proposed access road and driveways and existing public utilities/services. Existing buildings within and adjoining the lot shall be hatched and distances between the proposed and existing buildings shall be indicated.

b.

Structural Plans i. Foundation Plans and Details at scale of not less than 1:100. ii. Floor/Roof Framing Plans and Details at scale of not less than 1:100. TcIHDa

iii. Copyright 2010

CD Technologies Asia, Inc.

Details and Schedules of structural and civil works

Philippine Laws Premium Edition 2009

37

elements including those for deep wells, water reservoir, pipe lines and sewer system. c.

Structural Analysis and Design for all buildings/structures except for one storey and single detached building/structure with a total floor area of 20.00 sq. meters or less.

d.

Boring and Load Tests Buildings or structures of three (3) storeys and higher, boring tests and, if necessary, load tests shall be required in accordance with the applicable latest approved provisions of the National Structural Code of the Philippines (NSCP). However, adequate soil exploration (including boring and load tests) shall also be required for lower buildings/structures at areas with potential geological/geotechnical hazards. The written report of the civil/geothecnical engineer Including but not limited to the design bearing capacity as well as the result of tests shall be submitted together with the other requirements In the application for a building permit. Boring test or load test shall also be done according to the applicable provisions of the NSCP which set forth requirements governing excavation, grading and earthwork construction, including fills and embankments for any building/structure and for foundation and retaining structures. ScaHDT

6.

e.

Seismic Analysis

f.

Other related documents

Electrical Documents Electrical plans and technical specifications containing the following:

Copyright 2010

a.

Location and Site Plans

b.

Legend or Symbols

c.

General Notes and/or Specifications

d.

Electrical Layout

e.

Schedule of Loads, Transformers, Generating/UPS Units

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

38

(Total kVA for each of the preceding items shall be indicated in the schedule)

7.

Copyright 2010

f.

Design Analysis

g.

One Line Diagram

Mechanical Documents a.

Location Plan and Key Plan

b.

General Layout Plan for each floor, drawn to a scale of not less than 1:100, indicating the equipment in heavier lines than the building outline with names of machinery and corresponding brake horsepower shall be indicated.

c.

Longitudinal and Transverse Sections of building and equipment base on the section lines drawn to scale of at least 1:100 sowing inter-floor relations and defining the manner of support of machines/equipment. Sections shall run longitudinally and transversely through the building length or width other than particularly detailed section for each machinery/equipment (fired and unfired pressure vessel, elevator, escalator, dumbwaiter, etc.).

d.

Isometric drawing of gas, fuel, oil system showing: Assembly of pies on racks and supports Legend and General Notes, Capacity per outlet and Complete individual piping system.

e.

Plans drawn to scale of 1:100 indicating location of store rooms, fuel tanks, fire extinguishing systems, fire doors, fire escape ladders and other protective facilities.

f.

Detailed drawings of all duct work installations, indicating dampers, controls, filters, fireproofing, acoustical and thermal insulation.

g.

Detailed Plans of machinery foundations and supports drawn to scale of at least 1:50.

h.

Detailed Plans of boilers and pressure vessels with a working pressure of above 70 kPa regardless of kilowatt rating.

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

39

i.

Design Computations and Detailed Plans of elevators, escalators, and the like drawn to scale of 1:50.

j.

For all installations, additions or alterations involving machinery of at most 14.9 kW, the signature of a duly licensed Mechanical Engineer shall be sufficient except fired and unfired pressure vessels, elevators, escalators, dumbwaiters, central/split/packaged type air conditioners and piping systems of steam, gas or fuels. HTCaAD

k.

8.

Detailed plans of fire suppression systems, location of automatic and smoke detectors and alarm and initiating devices use to monitor the conditions that are essential for the proper operation including switches for the position of gate valves as well as alert and evacuation signals; the detailed layout of the entire safe area to be protected and the heat/smoke ventilation system.

Sanitary Documents a.

For deep well, water purification plants, water collection and distribution systems, reservoirs, drainage and sewer systems, sewage treatment plants, malaria control structures, and sewage disposal systems: i.

Location Plan and Site Plan

ii. Detailed Plan and layout drawings of minimum scale 1:100

b.

iii.

Design Analysis and Technical Specifications

iv.

Cost Estimates

For pest and vermin control, sanitation; and pollution control facilities: i. Detailed plan, layout and drawing of abatement and control device of minimum scale 1:100

Copyright 2010

CD Technologies Asia, Inc.

ii.

Design analysis and technical specification

iii.

Cost Estimates

Philippine Laws Premium Edition 2009

40

9.

Plumbing Documents For all plumbing installations, additions and/or alterations involving hot and cold water supply, fixtures, sewage drainage and vent system, storm drainage and sewerage system within or adjacent to the building:

10.

a.

Location Plan and Site Plan of minimum scale 1:2000

b.

Plumbing Plans, Layouts and Details, of minimum scale 1:50

c.

Legend and General Notes

d.

Isometric drawings of the systems

e.

Design analysis and technical specifications

f.

Cost Estimates

Electronics Documents Electronic plans and technical specifications for wired or wireless telecommunications systems, broadcasting systems, including radio and TV broadcast equipment for commercial and training purposes, cable or wireless television systems, information technology (IT) systems, security and alarm systems, electronic fire alarm systems sound-reinforcement systems, navigational aids and controls, indoor and outdoor signages, electronically-controlled conveyance systems, electronic/computerized process controls and automation systems, building automation, management and control systems, including, but not limited to the following:

Copyright 2010

a.

General layout plans with legends

b.

Single line diagram

c.

Riser diagram

d.

Isometry of the system

e.

Equipment specifications

f.

Design analysis, as applicable

g.

Cost estimates

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

HAISEa

41

11.

Geodetic documents

Lot Survey Plans, including but not limited to:

12.

a.

Vicinity Map/Location Plan

b.

Lot Plan

c.

Relocation Survey Plan and Report

d.

Line and Grade

e.

Detailed Topographic Plan of the site and Immediate vicinity

Clearances from Other Agencies a.

A locational clearance shall be obtained by the owner/permittee from the City/Municipal Zoning Administration.

b.

Whenever necessary, written clearances shall be obtained from the various authorities exercising and enforcing regulatory functions affecting buildings/structures. Application for said clearances shall be requested by the owner/applicant and failure to receive reply within seven (7) days from receipt of the application for building permit shall be sufficient not to cause further delay in processing the building permit application by the Building Official. Such authorities who are expected to enforce their own regulations are: i. Department of Public Works and Highways (DPWH)

Copyright 2010

CD Technologies Asia, Inc.

ii.

Air Transportation Office (ATO)

iii.

Housing and Land Use Regulatory Board (HLURB)

iv.

Local Government Unit (LGU)

v.

Department of Tourism (DOT)

vi.

Department of Environment and Natural Resources

Philippine Laws Premium Edition 2009

42

(DENR) vii. Department of Transportation and Communication (DOTC) viii. Department of Interior and Local Government (DILG) ix.

Philippine Ports Authority (PPA)

x.

Department of Education (DepEd)

xi.

Department of Health (DOH)

xii. Philippine Institute of Volcanology and Seismology (PHIVOLCS) xiii. Laguna Lake Development Authority (LLDA)

DIcTEC

xiv. Manila Waterworks and Sewerage System (MWSS) xv. National Water Resources Board (NWRB) xvi. Department of Agrarian Reform (DAR) xvii. Department of Agriculture (DA) xviii. (DOLE)

Department of Labor and Employment

xix. National Housing Authority (NHA) xx. National Council for the Welfare of Disabled Persons (NCWDP) SECTION 303.

Processing of Building Permits. —

The flow of processing of building permit shall follow the procedure shown in Figure III.3. 1.

Building Permit Application a.

When satisfied that all plans, specifications and other documents are in order, the Building Official gives due course to the application. EDCIcH

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

43

b.

The OBO verifies conformity of the proposed buildings/structures with the land use zoning ordinance of the city/municipality. If the project has been issued a development permit such as residential, commercial, industrial, institutional, memorial parks and other development by the HLURB or the Sanggunian Bayan/Panlungsod, an individual locational clearance shall not be required.

c.

The Building Official verifies whether applicants have secured the required section clearances from other agencies mentioned in the preceding section.

d.

The owner/permittee for any existing building/structure that shall undergo alterations, additions, conversions, renovations and/or repair not covered by Section 301, Sub-Section 3 of this IRR shall submit, in addition to other documents, the most recent Certificate of Occupancy when applying for a building permit. Under any of this case, the Locational Clearance shall not be required. DCcSHE

2.

Line and Grade Verification

The Line and Grade Section/Unit of the OBO:

Copyright 2010

a.

Verifies the lot plan as reflected in the Torrens Title, Original Certificate of Title (OCT)/Transfer Certificate of Title (TCT) and its relation to the proposed buildings/structures.

b.

Checks compliance to establish easements/setbacks and determines grades in relation to road lots, property lines, streets or highways, whether existing or proposed as reflected in the land use zoning or development plan of the city/municipality including road widening, construction of various public utilities/services and other infrastructure projects along creeks, esteros, waterways, subject to a written clearance from the DPWH.

c.

Verifies that at least one (1) side of the lot has direct access to a street/alley and that grades in relation to road lots and streets or highways, whether existing or

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

44

proposed conform to the requirements. 3.

Architectural The Architectural Section/Unit evaluates building/structure documents as to compliance to technical requirements for:

Copyright 2010

a.

Types of Construction

b.

Requirements of Fire Zones and Fire Resistive Regulation

c.

Building projections over public streets

d.

Access Streets/Roads and Alleys

e.

Architectural Interior/Interior Design

f.

Classification and General Requirements of all Buildings by Use or Occupancy

g.

Maximum Height of Buildings/Structures

h.

Parking and Loading/Unloading Space Requirement

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

45

4.

i.

Corner Buildings with Chaflans

j.

Occupant Load

k.

Glazing of Opening

l.

Architectural Accessibility Features

m.

Light and Ventilation

n.

Construction of Buildings/Structures within the obstacle limitation surfaces of Aerodromes

o.

Buildings and other Ancillary Cemeteries and Memorial Parks

Structures

within

Civil/Structural The

Copyright 2010

acCETD

Civil/Structural

CD Technologies Asia, Inc.

Section/Unit

Philippine Laws Premium Edition 2009

evaluates

building/structure 46

documents as to compliance to technical requirements for:

5.

a.

General Design and Construction Requirements

b.

Structural Design Requirements

c.

Excavations, Foundations and Retaining Walls

d.

Prefabricated Construction

e.

Protection and Safety Requirements for Construction, Demolition and Excavation

f.

Abatement/Demolition of Buildings

g.

Plastics

h.

Signs

Electrical The Electrical Section/Unit evaluates building/structure documents as to compliance to technical requirements for Electrical Regulations.

6.

Mechanical The Mechanical Section/Unit evaluates building/structure documents as to compliance to technical requirements for Mechanical Regulations.

7.

Sanitary The Sanitary Section/Unit evaluates building/structure documents as to compliance to technical requirements under the Sanitary Engineering Law (RA 1364).

8.

Plumbing The Plumbing Section/Unit evaluates building/structure documents as to compliance to technical requirements under the Plumbing Law (RA 1378).

9.

Electronics The Electronics Section/Unit evaluates building/structure documents as to compliance to technical requirements.

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

47

10.

Fire Safety Requirements The Building Official shall refer one (1) set of plans and specifications to the City/Municipal Fire Marshall (C/MFM), Bureau of Fire Protection (BFP), for his review and recommendations with respect to fire safety and control requirements. The C/MFM shall submit his report and recommendations to the Building Official within five (5) working days from date of referral. Failure of the C/MFM to act within said period shall mean that the plans and specifications conform to all the requirements of the Fire Code of the Philippines (FCP). In case of non-issuance, suspension or revocation of the said requirements by the C/MFM, he shall so state in writing the reasons or grounds therefor.

SECTION 304.

Issuance of Building Permit. —

1.

When the application for building permit and the plans and specifications submitted herewith conforms to the requirements of the Code and its IRR, the Building Official shall within fifteen (15) days from payment of the required fees by the applicant, issue the building permit applied for.

2.

The Building Official may issue a permit for the construction of only a part or portion of a building/structure whenever the plans and specifications submitted together with the application do not cover the entire building/structure.

3.

The Building Official may issue a Ground Preparation and Excavation Permit even while the building permit application is still being processed subject to payment of the corresponding fees. cADEHI

4.

Copyright 2010

For excavations more than 50.00 cu. meters and more than 2.00 meters In depth, the owner/permittee shall post a cash bond of fifty thousand pesos (P50,000.00) for the first 50.00 cu. meters and three hundred pesos (P300.00) for every cu. meters in excess of 50 cu. meters until the building permit is issued, said excavations shall not exceed 100.00 cu. meters or 3.00 meters in depth and shall not be left open without any work being done in the site for more than one hundred twenty (120) days, otherwise the cash bond shall be forfeited in favor of the government to cover the expense for the backfilling of the excavation should the owner/permittee fail to restore the same. If the bond is insufficient to effect the necessary restoration;

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

48

additional cost to be incurred to complete the restoration shall be charged to the account of the owner/permittee or to whoever shall assume ownership of the property. If the owner/permittee refuses backfilling of the excavation, the Building Official shall initiate legal proceedings. Terms and Conditions of Permits The issued building permit shall be subject to the following terms and conditions:

Copyright 2010

a.

That under Article 1723 of the Civil Code of the Philippines, the engineer or architect who drew up the plans and specifications for a building/structure is liable for damages if within fifteen (15) years from the completion of the building/structure, the same should collapse due to defect in the plans or specifications or defects in the ground. The engineer or architect who supervises the construction shall be solidarily liable with the contractor should the edifice collapse due to defect in the construction or the use of inferior materials.

b.

This permit shall be accompanied by the various applicable ancillary and accessory permits, plans and specifications signed and sealed by the corresponding design professionals who shall be responsible for the comprehensiveness and correctness of the plans in compliance to the Code and its IRR and to all applicable referral codes and professional regulatory laws.

c.

That the proposed construction/ erection/ addition/ alteration/ renovation/ conversion/ repair/ moving/ demolition, etc. shall be in conformity with the provisions of the National Building Code, and its IRR. i.

That prior to commencement of the proposed projects and construction an actual relocation survey shall be conducted by a duly licensed Geodetic Engineer.

ii.

That before commencing the excavation the person making or causing the excavation to be made shall notify in writing the owner of adjoining property not less than ten (10) days before such excavation is to be made and show how the adjoining property should be protected.

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

49

iii.

That the supervising Architect/Civil Engineer shall keep at the jobsite at all times a logbook of daily construction activities wherein the actual daily progress of construction including tests conducted, weather condition and other pertinent data are to be recorded, same shall be made available for scrutiny and comments by the OBO representative during the conduct of inspection his/her inspection pursuant to Section 207 of the Code. aTCADc

Copyright 2010

iv.

That upon completion of the construction, the Owner shall submit the logbook duly signed and sealed to the Building Official including as-built plans and other documents and shall also prepare and submit a Certificate of Completion of the project stating that the construction of the building/structure conform to the provision of the Code, its IRR as well as the plans and specifications.

v.

All such changes, modifications and alterations shall likewise be submitted to the Building Official and the subsequent amendatory permit therefor issued before any work on said changes, modifications and alterations shall be started.

d.

That no building/structure shall be used until the Building Official has issued a Certificate of Occupancy therefor as provided in the Code. However, a partial Certificate of Occupancy may be issued for the Use/Occupancy of a portion or portions of a building/structure prior to the completion of the entire building/structure.

e.

That this permit shall not serve as an exemption from securing written clearances from various government authorities exercising regulatory function affecting buildings/structures.

f.

When the construction is undertaken by contract, the work shall be done by a duly licensed and registered contractor pursuant to the provisions of the Contractor's License Law (RA 4566).

g.

The Owner/Permittee shall submit a duly accomplished prescribed "Notice of Construction" to the Office of the

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

50

Building Official prior to any construction activity. h.

The Owner/Permittee shall put a Building Permit sign which complies with the prescribed dimensions and information, which shall remain posted on the construction site for the duration of the construction. (Figs. III.4. and III.5).

SECTION 305.

Validity of Building Permits. —

The issuance of a building permit shall not be construed as an approval or authorization to the permittee to disregard or violate any of the provisions of the Code. Whenever the issuance of a permit is based on approved plans and specifications which are subsequently found defective, the Building official is not precluded from requiring permittee to effect the necessary corrections in said plans and specifications or from preventing or ordering the stoppage of any or all building operations being carried on thereunder which are in violation of the Code. A building permit issued under the provisions of the Code shall expire and become null and void if the building or work authorized therein is not commenced within a period of one (1) year after the issuance of the building permit, or is suspended or abandoned at any time after it has been commenced for a period of one hundred twenty (120) days. SECTION 306. Permits. —

Non-Issuance, Suspension or Revocation of Building

The Building Official may order or cause the non-issuance, suspension or revocation of building permits on any or all of the following reasons or grounds: 1.

Errors found in the plans and specifications;

2.

Incorrect or inaccurate data or information supplied;

3.

Non-compliance with the provisions of the Code or any rules or regulations.

Notice of non-issuance, suspension or revocation of building permits shall always be made in writing, stating the reason or grounds thereof.

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

51

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

52

SECTION 307.

Appeal. —

Within fifteen (15) days from the date of receipt of advice of the non-issuance, suspension or revocation of permits, the applicant/permittee may file an appeal with the Secretary who shall render his decision within fifteen days from date of receipt of notice of appeal. The decision of the Secretary shall be final subject only to review by the Office of the President. SDHITE

SECTION 308. 1.

The owner of the Building who is issued or granted a building permit under the Code shall engage the services of a duly licensed architect or civil engineer to undertake the full time inspection and supervision of the construction work.

2.

Such architect or civil engineer may or may not be the same architect or civil engineer who is responsible for the design of the building.

3.

It is understood however that in either case, the designing architect or civil engineer is not precluded from conducting inspection of the construction work to check and determine compliance with the plans and specifications of the building submitted.

4.

There shall be kept at the jobsite at all times a logbook wherein the actual progress of construction including tests conducted, weather conditions and other pertinent data are to be recorded.

5.

Upon completion of the construction, the said licensed architect or civil engineer shall submit the logbook, duly signed and sealed, to the Building Official. He shall also prepare and submit a Certificate of Completion of the project stating that the construction of building conforms to the provisions of the Code as well as with the approved plans and specifications.

SECTION 309. 1.

Copyright 2010

Inspection and Supervision of Work. —

Certificate of Occupancy. —

The owner/permittee shall submit to the OBO an application of Certificate of Occupancy together with a duly notarized Certificate of Completion together with the construction logbook, as-built plans and specifications and the Building Inspection Sheet all signed by whoever is the contractor (if the

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

53

construction is undertaken by contract) and signed and sealed by the Owner's duly licensed Architect or Civil Engineer who undertook the full time inspection and supervision of the construction works. Said Plans and Specifications shall reflect faithfully all changes, modifications and alterations made on the originally submitted Plans and Specifications on file with the OBO which are the basis of the issuance of the original building permit. The as-built Plans and Specifications may be just an orderly and comprehensive compilation of all the documents, which include the originally submitted plans and specifications and all amendments thereto as actually built or they may be an entirely new set of plans and specifications accurately describing and/or reflecting therein the building/structure as actually built. 2.

A notification to conduct final inspection shall be endorsed by the OBO to the C/MFM, BFP, who shall issue a Fire Safety Inspection Certificate within five (5) workings days if the Fire Safety requirement shall have been complied. If, after the prescribed period no action is taken by the C/MFM, the Building Official may issue the Certificate of Occupancy with the condition that the Fire Safety requirements shall be complied with, within the prescribed period set forth in the Fire Code of the Philippines (PD 1185).

3.

The OBO undertakes the final inspection, verification and/or review of the building/structure based on the Certificate of Completion, construction logbook, building inspection sheets, original and as-built plans and specifications, as the case may be and specifications on the prescribed standard form according to the requirements set forth under Section 303.

4.

Prior to the issuance of the Certificate of Occupancy, the OBO shall prepare the corresponding fees and order of payment. The Building Official then issues the Certificate of Occupancy in the form prescribed therefor after all fees are paid. AaITCS

a.

Copyright 2010

A partial Certificate of Occupancy may be issued for the use or occupancy of a portion or portions of a building or structure prior to the completion of the entire building or structure, through the proper phasing of its major independent portions without posing hazards to its

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

54

occupants, the adjacent building residents and general public. b.

A building for which a Certificate of Occupancy has been issued may further be issued other Certificates of Occupancy due to changes in use, whether partly or wholly, provided, that the new use/s or character/s' of occupancy conforms with the requirement of the Code and its IRR. RULE IV Types of Construction

SECTION 401.

Types of Construction. —

For purposes of the Code and its IRR, all buildings proposed for construction shall be classified according to the following types:

Copyright 2010

1.

Type I — shall be of wood construction. The structural elements may be any of the materials permitted by the Code.

2.

Type II — shall be of wood construction with protective fire-resistant materials and one-hour fire-resistive throughout, except, that permanent non-bearing partitions may use fire-retardant treated wood within the framing assembly with one-hour resistivity.

3.

Type III — shall be of masonry and wood construction. Structural elements may be any of the materials permitted by the Code provided, that the building shall be one-hour fire-resistive throughout. Exterior walls shall be of incombustible fire-resistive construction.

4.

Type IV — shall be steel, iron, concrete, or masonry construction and walls, ceiling and permanent partitions shall be of incombustible fire-resistive construction, except, that permanent non-bearing partitions of one-hour fire-resistive construction may use fire-retardant treated wood within the framing assembly.

5.

Type V — shall be four-hour fire-resistive throughout and the structural elements shall be of steel, iron, concrete, or masonry construction.

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

55

SECTION 402.

Changes in Types. —

No change shall be made in the type of construction of any building which would place the building in a different sub-type or type of construction unless such building is made to comply with the requirements for such sub-type of construction: Except, when the changes is approved by the Building Official upon showing that the new or proposed construction is less hazardous, based on life and fire risk, than the existing construction. SECTION 403.

Requirements on Type of Construction. —

The following standards are prescribed: 1.

Fire Resistive Requirements a.

Exterior bearing and non-bearing walls of Types II and III Constructions shall have one hour fire-resistive rating, while those of Types IV and V shall have four-hour fire-resistive rating.

b.

Interior bearing walls, permanent partitions, floors, and roofs of Types II, III and IV Construction shall have one-hour fire-resistive rating while those of Type V shall have three-hour fire-resistive rating for bearing walls and one-hour fire-resistive rating for vertical openings, floors and roofs. ISCaDH

2.

c.

Structural frames of Types II and III Construction shall have one-hour fire-resistive rating, while those of Type IV shall have two-hour fire-resistive rating and those of Type V shall have three hour fire-resistive rating.

d.

Exterior doors and windows shall have one hour fire-resistive rating for all Types.

Interior Wall and Ceiling Finishes a.

Copyright 2010

Finishes for interior walls and ceilings of any building shall be classified according to their flame-spread characteristic using generally accepted engineering standards. The smoke density shall not be greater than that obtained from burning of untreated wood under similar conditions when tested in accordance with the 'Tunnel Test" in the way intended for use. The products

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

56

of combustion shall be no more toxic than the burning of untreated wood under similar conditions. These finishes include: interior wainscoting, paneling, or other finish applied structurally or for decoration, acoustical correction, frames and trims of doors and windows, surface insulation or similar purposes. HacADE

3.

b.

Requirements for flame-spread characteristics of finishes shall not apply to frames and trim of doors and windows and to materials which are less than 1.00 millimeter in thickness cemented to the surface of walls or ceilings.

c.

Materials required to be flame-spread proofed shall be treated with a flame-retardant having a flame-spread of fifty (50) or less as determined by the 'Tunnel Test'.

Standards for materials use in structural framework, exterior walls and openings, floors, exits, stairs & roofs shall be governed by the pertinent provision of the Fire Code of the Philippines. RULE V Requirements of Fire Zones

SECTION 501.

Fire Zones Defined. —

Fire zones are areas within which only certain types of buildings/structures are permitted to be constructed based on their use or occupancy, type of construction, and resistance to fire. EDcIAC

SECTION 502.

Buildings Located in More Than One Fire Zone. —

A building/structure which is located partly in one (1) fire zone and partly in another shall be considered to be in the more highly restrictive fire zone, when more than one third (1/3) of its total floor area is located in such zone. SECTION 503.

Copyright 2010

Moved Buildings. —

1.

Any building/structure moved within or into any fire zone shall be made to comply with all the requirements for buildings/structures in that fire zone.

2.

This shall also apply to pre-engineered or pre-fabricated

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

57

buildings/structures that may be dismantled and re-assembled. SECTION 504.

Temporary Buildings/Structures. —

1.

Temporary buildings such as reviewing stands and other miscellaneous structures conforming to the requirements of the Code, and sheds, canopies and fences used for the protection of the public around and in conjunction with construction work, may be erected in the fire zones by special permit from the Building Official for a limited period of time, and such buildings or structures shall be completely removed upon the expiration of the time limit stated in such permits.

2.

Erection of temporary buildings/structures to be located in restrictive and highly restrictive zones and which do not conform with the type of construction allowed or permitted within such zones may be allowed by the Building Official for a given period of time provided that, fire protective/preventive measures and fire suppression facilities are adequate.

SECTION 505.

Center Lines of Streets. —

The center line of adjoining street or alley may be considered an adjacent property line. Distances shall be measured at right angles to the street or alley. SECTION 506. 1.

Copyright 2010

Restrictions on Existing Buildings. —

Existing buildings or structures in fire zones that do not comply with the requirements for a new building erected therein shall not hereafter be enlarged, altered, remodeled, repaired or moved except as follows: a.

Such building is entirely demolished;

b.

Such building is to be moved outside the limits of the more highly restrictive Fire Zone to a zone where the building meets the minimum standards;

c.

Changes, alterations and repairs may be made provided that in any 12-month period, the value of the work does not exceed 20% of the value of the existing building, and provided that, such changes do not add additional combustible material, and do not, in the opinion of the Building Official, increase the fire hazard;

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

58

d.

Additions thereto are separated from the existing building by fire walls, as set forth in Section 506 (b);

e.

Damage from fire or earthquake, typhoons or any fortuitous event may be repaired, using the same kind of materials of which the building or structure was originally constructed, provided that, the cost of such repair shall not exceed 20% of the replacement cost of the building or structure.

SECTION 507.

Designation of Fire Zones. —

The legislative body of the LGU may enact ordinances for the purpose of designating fire zones based on the parameters and guidelines set forth in this Section. acIHDA

1.

Copyright 2010

Designation of Fire Zones is purposely for management, prevention, control and suppression of conflagration that may occur in population centers. The designation of fire zones is as follows: a.

Non-Fire Restricted Zones: These are areas where siting of buildings/structures are permitted without fire-resistivity measures, often located in the country sides or rural areas where commercial and industrial and other buildings are sparsely constructed, or may be clustered in small groups like farm lands wherein dwellings are built of indigenous materials such as bamboo, sawali, nipa, cogon, palm leaves and wood up to Types I and II Construction as classified in Section 401 of the Code.

b.

Fire Restrictive Zones: Areas wherein siting of buildings/structures are permitted within prescribed fire-resistivity measures for exterior walls of at least two-hour fire resistivity. Usual locations in suburban areas are permitted to be built with at least one-hour fire-resistivity throughout as Types II, III to IV Constructions as prescribed in Section 401 of the Code.

c.

Highly Fire Restrictive Zones: Areas wherein highly fire-resistive or noncombustible buildings/structures and/or construction assemblies of no less than three to

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

59

four-hour fire-resistive construction materials are used throughout, including exterior walls. Only Types IV and V Constructions are permitted in the areas. RULE VI Fire-Resistive Requirements in Construction SECTION 601.

Fire-Resistive Rating Defined. —

Fire-resistive rating means the degree to which a material can withstand fire as determined by generally recognized and accepted testing methods. SECTION 602.

Fire- Resistive Time Period Rating. —

Fire-resistive time period rating is the length of time a material can withstand being burned which may be one-hour, two-hours, four-hours, etc. SECTION 603.

Fire-Resistive Standards. —

All materials of construction, and type of materials and assemblies or combinations thereof shall conform to the following fire-resistive ratings: Type of Assembly and Material

4 hrs.

3 hrs.

2 hrs.

1 hr.

Floor Construction Solid R.C. slab - Average cover to reinforcement - Overall Depth

25 150

25 150

20 125

15 100

Solid pre-stressed Concrete slab - Average cover to tendons - Overall Depth

65 150

50 150

40 125

25 100

Partitions - Solid concrete - Solid masonry - Hollow unit masonry

175 200 300

175 175 250

150 150 200

125 125 150

75 100

50 75

38 55

25 38

Protection for metal structural members - Concrete - Masonry - Metal lath with vermiculite or perlite Copyright 2010

Minimum thickness (in millimeter) for the given fire resistance

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

60

gypsum plaster

50

38

20

12

Exterior Wall -Solid concrete - Solid masonry - Hollow masonry

180 200 300

150 175 250

125 150 200

75 100 150

Column (all faces exposed) - Reinforced concrete

450

400

300

200

SECTION 604.

Fire- Resistive Regulations. —

The Secretary shall prescribe standards and promulgate rules and regulations on the testing of construction materials for flame-spread characteristics, tests on fire damages, fire tests of building construction and materials, door assemblies and tinclad fire doors and window assemblies, the installation of fire doors and windows and smoke and fire detectors for fire protective signaling system, application and use of controlled interior finish, fire-resistive protection for structural members, fire-resistive walls and partitions, fire-resistive floor or roof ceiling, fire-resistive assemblies for protection of openings and fire-retardant roof coverings. AIaDcH

RULE VII Classification and General Requirements of All Buildings By Use or Occupancy SECTION 701. 1.

Occupancy Classified. —

There are 10 Groups of Occupancies sub-divided into 25 Divisions. The accompanying matrix shows the Groupings and Divisions and the corresponding uses. The final column indicates the Zoning Classification. a.

Buildings proposed for construction shall be identified according to their use or the character of its occupancy and shall be classified as follows: i.

Group A — Residential Dwellings

Group A Occupancies shall include: Division 1 — Residential building/structure for exclusive use of single family occupants including school or company staff housing; single (nuclear) family dwellings; churches or similar paces of worship; church Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

61

rectories; community facilities and social centers; parks, playgrounds, pocket parks, parkways, promenades and play lots; clubhouses and recreational uses such as golf courses, tennis courts, basketball courts, swimming pools and similar uses operated by the government or private individuals as membership organizations for the benefit of their members, families, and guests and not operated primarily for gain. EaHIDC

Division 2 — Residential building for the exclusive use of non-leasing occupants not exceeding 10 persons including single-attached or duplex or townhouses, each privately-owned; school dormitories (on campus); convents and monasteries; military or police barracks/dormitories; pre-schools, elementary and high schools, provided that they do not exceed 16 classrooms; outpatient clinics, family planning clinics, lying-in clinics, diagnostics clinics, medical and clinical laboratories; branch library and museums; steam/dry cleaning outlets; party needs and accessories (leasing of tables and chairs, etc.). ii.

Group B — Residentials, Hotels and Apartments

Group B Occupancies shall be multiple dwelling units including boarding or lodging houses, hotels, apartment buildings, row houses, convents, monasteries and other similar building each of which accommodates more than 10 persons. iii.

Group C — Education and Recreation

Group C Occupancies shall be buildings used for school or day-care purposes, involving assemblage for instruction, education, or recreation, and not classified in Group I or in Division 1 and 2 or Group H Occupancies. iv.

Group D — Institutional

Group D Occupancies shall include: Division 1 — Mental hospitals, mental sanitaria, jails, prisons, reformatories, and buildings were personal Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

62

liberties of inmates are similarly restrained. Division 2 — Nurseries for full-time care of under kindergarten age, hospitals, sanitaria, homes with non-ambulatory patients, and buildings each accommodating more than five

children nursing similar persons.

cAHDES

Division 3 — Nursing homes for ambulatory patients, homes for children of kindergarten age or over, each accommodating more than five persons: Provided, that Group D Occupancies shall not include buildings used only for private or family group dwelling purposes. v.

Group E — Business and Mercantile

Group E Occupancies shall include: Division 1 — Gasoline filling and service stations, storage garages and boat storage structures where no work is done except exchange of parts and maintenance requiring no open flame, welding, or the use of highly flammable liquids. Division 2 — Wholesale and retail stores, office buildings, drinking and dining establishments having an occupant load of less than one hundred persons, printing plants, police and fire stations, factories and workshops using not highly flammable or combustible materials and paint stores without bulk handlings. Division 3 — Aircraft hangars and open parking garages where no repair work is done except exchange of parts and maintenance requiring no open flame, welding or the use of highly flammable liquids. vi.

Group F — Industrial

Group F Occupancies shall include: ice plants, power plants, pumping plants, cold storage, and creameries, factories and workshops using incombustible and non-explosive materials, and storage and sales rooms for incombustible and non-explosive materials. Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

63

vii. Group G — Storage and Hazardous Groups G Occupancies shall include: Division 1 — Storage and handling of hazardous and highly flammable material. Division 2 — Storage and handling of flammable materials, dry cleaning plants using flammable liquids; paint stores with bulk handling, paint shops and spray painting rooms. Division 3 — Wood working establishments, planning mills and box factories, shops, factories where loose combustible fibers or dust are manufactured, processed or generated; warehouses where highly combustible materials is stored. Division 4 — Repair garages. Division 5 — Aircraft repair hangars. viii. Group H — Assembly Other Than Group I Group H Occupancies shall include: Division 1 — Any assembly building with a stage and an occupant load of less than 1000 in the building. Division 2 — Any assembly building without stage and having an occupant load of 300 or more in the building. SIaHTD

Division 3 — Any assembly building without a stage and having an occupant load of less than 300 in the building. Division 4 — Stadia, reviewing stands, amusement park structures not included within Group I or in Division 1, 2, and 3 of this Group. ix. Group I — Assembly Occupant Load 1000 or More Group I Occupancies shall be any assembly building with a stage and an occupant load of 1000 or more in the building. Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

64

x.

Group J — Accessory

Group J Occupancies shall include: Division 1 — Agricultural structures. Division 2 — Private garages, carports, fences over 1.80 meters high, tanks, swimming pools and towers. Division 3 — Stages, platforms, pelota, tennis, badminton or basketball courts, tombs, mausoleums, niches, aviaries, aquariums, zoo structures, banks and record vaults Other subgroupings or divisions within Groups A to J may be determined by the Secretary. Any other occupancy not mentioned specifically in this Section, or about which there is any question, shall be included in the Group which it most nearly resembles based on the existing or proposed life and fire hazard. Table VII.1. Schedule of Principal, Accessory and Conditional Use/Occupancy of Building/Structure USE General U S E Character of Occupancy of Zoning Classification

PRINCIPAL

ACCESSORY

CONDITIONAL

Building/Structure Group A - Residential (Dwellings) Division A-1 1. Indigenous family dwelling units schools, provided Residential R-1 — a low-density (Residential 2. Single-detached units not exceed three residential zone characterized building/structure 3. School or company staff housing classrooms and shall be mainly by single-family, single for exclusive use 4. Single (nuclear) family dwellings less than 500 meters detached dwellings with the of single family 5. Churches or similar places existing school usual community ancillary occupants) of worship similar course and are uses on a neighborhood scale, 6. Church rectories adequate parking such as executive subdivisions 7. Community facilities and provided in the local zoning social centers communities which are not 8. Parks, playgrounds, pocket houses with no more subdivisions. parks, parkways, promenades boarders. Copyright 2010

CD Technologies Asia, Inc.

1. Customary accessory uses incidental to any of the principal

that they do

uses housed in the same

(3)

Division A-1 (or R-1 class)

located not

building/structure, provided that

from nearest

such accessory uses shall not

offering

include any activity conducted for

equipped with

monetary gain or commercial and relatively exclusive residential purposes such as servants

Philippine Laws Premium Edition 2009

1. Preparatory

or as ordinance.

quarter, private garage, guardhouse, 2. Boarding home laundries, non-commercial

than eight (8)

65

and playlots

garages, houses for pets such

3. Neighborhood

Clubhouses and recreational

as dogs, birds, rabbits and the like

selling

uses such as golf courses, tennis

of not more than 4.00 sq. meters

provided that

courts, basketball courts, swimming

in floor area, pump houses and

exceed 10%

pools and similar uses operated

generator houses.

area (GFA) of

convenience stores 9. miscellaneous items, such stores shall not of the gross floor the dwelling unit by the government or private

2. Auxiliary uses customarily

and provided

that no liquor shall individuals as membership

conducted in dwellings and homes

be allowed for

organizations for the benefit

for the practice of one's profession

of their members, families,

such as offices of physicians,

shops,

and guests and not operated

surgeons, dentists, architects,

shall not

primarily for gain.

engineers, lawyers and other

floor area of

sale. 4. Audio-video

and computer rental provided that such shops exceed 10% of the total the dwelling unit. professionals provided that such

5. Home

occupation engaging in professionals are members of the

an in-house

family residing in the premises;

dressmaking,

provided further, that not more than

provided that

three (3) semiprofessional assistants

not occupy

are employed at any time, that in

total floor

no case that more than 20% of the

the number of

floor area of the building be used

such

for said professional practice or

exceed three

home occupation for engaging

owner; there

an in-house business such as

the outside

business such as tailoring, and baking, the area used shall more than 20% of the area of the dwelling unit; persons engaged in business/industry shall not (3) inclusive of the shall be no change in appearance of the dressmaking, tailoring, baking and building/structure or premises; the like, provided that the number of

no home

persons engaged in such

conducted in

business/industry shall not exceed

accessory

five (5), inclusive of the owner; there

generated by

shall be no change in the outside

occupation in

appearance of the building or

than would

premises; no home occupation shall

in a

be conducted in any customary

any need for

accessory uses cited above; no

the conduct

traffic shall be generated by such

shall be met

home occupation in greater volume

other than in

than would normally be expected in

no equipment

occupation shall be any customary use; no traffic shall be such home greater volume normally be expected residential neighborhood and parking generated by of such home occupation off the street and in place a required front yard; or process shall be Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

66

a residential neighborhood and any

used in such

need for parking generated by the

creates noise,

conduct of such home occupation

fumes, odors

shall be met off the street and in a

detectable to

place other than in a required front

visual or

yard; no equipment or process shall

radio or

be used in such home occupation

causes

which creates noise, vibration, glare,

of the

home occupation which vibration, glare, or electrical interference the normal senses and audible interference in any television receivers or fluctuation in line voltage premises. fumes, odors or electrical

7. Home

industry classified as interference detectable to the

cottage

normal senses and visual or

home industry

audible interference in any radio

than 30% of

or television receivers or causes

(GA) of the

fluctuation in line voltage

employees

of the premises.

persons and

industry provided that such shall not occupy more the gross floor area dwelling unit with not to exceed five (5) shall have no change 3. Home industry classified as cottage

or alteration

in the outside industry provided that such home

appearance

industry shall not occupy more than

unit and shall

of the dwelling not be a 30% of the floor area of the dwelling hazard/nuisance; allotted unit; there shall be no change or

capitalization

alteration in the outside appearance

the

of the dwelling unit and shall not be

Department

a hazard/nuisance; allotted

(DTI); no

capitalization shall not exceed the

be conducted

capitalization as set by the

accessory

Department of Trade and Industry

generated by

(DTI); shall consider same provisions

greater

as enumerated in number 2,

be expected

Profession or Home Occupation,

neighborhood

this Section.

parking

shall not exceed capitalization as set by the of Trade and Industry home industry shall in any customs use; no traffic shall be such home industry in volume than would normally in a residential and any need for generated by the conduct 4. Recreational facilities for the

of such home

occupation shall be exclusive use of the members of the

met off the

family residing within the premises,

other than in

such as swimming pool, pelota

no equipment

court, etc.

used in such

street and in a place a required front yard or process shall be home industry which Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

67

5. Religious use

creates noise,

6. Multi-purpose/Barangay Hall

odors or

7. Pre-School

detectable to

8. Sports club

and visual or

9. Clinic, nursing and convalescing

in any radio

vibration, glare, fumes, electrical interference the normal senses audible interference or television receivers home, health center

or causes

fluctuation in line voltage 10. Plant nursery

of the

premises Division A-2 1. Single-attached or duplex or and voice studios Residential R-2 - a medium (residential building town-houses, each privately owned the classes or density residential use or for the exclusive use 2. School dormitories (on campus) are held in occupancy, characterized of non-leasing 3. Convents and monasteries and air-conditioned mainly as a low-rise occupants not 4. Military or police single-attached, duplex or exceeding barracks/dormitories nursery or convalescent 10 persons) 5. All uses allowed in Division for exclusive use as multiple A-1 (or for R-1 class) or charitable institutions family dwellings. This buildings/structures approval of the Building Official 6. Pre-schools, elementary such conditions and within semi-exclusive and high schools, provided deemed appropriate subdivisions and that they do not exceed no actual display, semi-exclusive residential sixteen (16) classrooms transfer, or lending of the office 7. Outpatient clinics, family in the premises and with subdivisions. planning clinics, lying-in floor area (GFA) not clinics, diagnostic clinics, 30% of the building GFA medical and clinical laboratories hotels/hometels types of R-2 use or occupancy, 8. Branch library and museum refilling and retailing of 9. Steam/dry cleaning outlets drinking water provided that 10. Party needs and accessories from local health a. Basic R-2 : single-attached (leasing of tables and chairs, etc.) and certification of or duplex building/structure

1. Customary incidental home

1. Ballet, dance

occupations such as barber and

provided that

beauty shops, tailoring and dress

instructions

shops, neighborhood convenience

soundproofed

stores, retail drug stores

buildings 2. Sanitaria,

multilevel building/structure homes 3. Philanthropic upon includes R-2 structures and subject to safeguards as 4. Offices

with sale,

communities which are not commodities subject gross exceeding There shall be two (2) general 5. Apartment 6. Processing, to wit: bottled clearances department adequate

supply from the water

of from one (1) storey up to supply

concessionaire shall be

three (3) storeys in height secured.

and with each use as 7. Home occupation for the practice of

single-family dwellings and; one's

profession or for engaging in an business such as Copyright 2010

in-house

b. Maximum R-2: low-rise

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

68

dressmaking, tailoring, baking, barber

multi-level building/structure

shops and the like,

of from three (3) up to five (5)

the area in use shall

storeys in height and for use

and

beauty

provided that not 30% of the gross floor

exceed

as multiple family dwellings area (GFA) of

the dwelling unit with the number of persons engaged in such business/industry not exceeding ten (10) inclusive of owner; there shall be no change in the outside appearance of the building or premises, no

home

occupation shall be conducted in any customary accessory use; no traffic shall be generated by such

home

than

would

occupation in greater volume normally be expected in a residential neighborhood and any need for

parking

generated by the conduct of such

home

occupation shall be met off the street and in a place other than in a required front yard; no equipment or

process

shall be used in such home occupation which creates noise, vibration, glare, fumes, odors or electrical interference detectable to the normal senses and visual or audible interference in any radio or television receivers

or

causes fluctuation in line voltage of the premises. 8. Car barns for not more than three (3) units. 9. LPG retailing with a maximum of twenty

(20)

units of LPG tanks at any

given

time 10. Recreational facilities such as resorts, swimming pools, clubhouses and similar Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

uses 69

except carnivals and fairs 11. Bank branches, savings/loans/lending shops. 12. Driving range Group B - Residential (Buildings/Structures, Hotels and Apartments) Division B-1 uses in R-1

1. All uses permitted in Divisions Residential R-3 - a high-density A-1 and A-2 (or for R-1 class appropriate residential use or occupancy, and R-2 class) buildings/structures characterized mainly as a 2. Leased single-detached dwelling low-rise or medium-rise unit, cottage with more than one building/structure for exclusive (1) independent unit and duplexes. use as multiple family dwellings 3. Boarding and lodging houses with mixed housing types. R-3 4. Multiple-housing units for lease structure may include low-rise or still for sale or medium-rise residential 5. Townhouses, each privately owned condominium buildings that are 6. Boarding houses already commercial in nature and 7. Accessories (shop-houses), scale. There shall be two (2) rowhouses, townhouses, general types of R-3 use or tenements and apartments occupancy, to wit: 8. Multiple privately-owned condominium units or tenement a. Basic R-3: rowhouse houses (residential building building/structure of from one for the exclusive use of non-leasing (1) storey up to three (3) occupants not exceed ten (10) storeys in height and with each persons and of low-rise type unit for separate use as single (up to five (5) storeys maximum family dwellings; and building height) 9. Hotels, motels, inns, pension b. Maximum R-3 : medium-rise houses and apartels multi-level building! structure of 10. Private or off-campus dormitories. from six (6) up to twelve (12) 11. Elementary schools and high storeys in height and for use schools, provided that these will as multiple family dwellings. not exceed twenty (20) classrooms

1. All customary accessory uses

1. All conditional

allowed in Divisions A-1 and

and R-2 with

A-2 (or for R-1 class and R-2 class)

regulations

buildings/structures 2. Branch library and museum 3. Hometel 4. Vocational school

Residential R-4 - a medium to high-density residential use or

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

70

occupancy, characterized mainly as a low-rise townhouse building/structure for exclusive use as multiple family dwellings. The term R-4 specifically refers to the building/structure on an individual lot (a townhouse unit) and generally refers to the series or rows of R-4 buildings/structures within a subdivided lot or property (an R-4 development). 1. Residential R-5 - a very

Multi-family residential buildings

such as condominium, high-rise high-density residential use or residential buildings/structures, occupancy, characterized mainly multi-level apartments, tenements, as a medium-rise or high-rise mass housing, etc. taller than five condominium building/structure (5) storeys but not more than for exclusive use as multiple family twelve (12) storeys dwelling. Group C Education and Recreation Division C-1

1.

2. 3. 4. 5. 6.

7. 8.

Educational institutions like schools, colleges, universities, vocational, institutions, seminaries, convents, including school auditoriums, gymnasia, reviewing stands, little theaters, concert halls, opera houses. Seminar/workshop facilities Training centers/facilities Libraries, museums, exhibition halls and art galleries Civic centers, clubhouses, lodges, community centers. Churches, mosque, temples. shrines, chapels and similar places of worship Civic or government centers Other types of government buildings

Division C-2 1. Amusement halls and parlors GI (General Institutional) - a 2. Massage and sauna parlors community to national level of Copyright 2010

CD Technologies Asia, Inc.

1. Government centers to house

Philippine Laws Premium Edition 2009

national, regional or local offices

71

3. Health studios and reducing institutional use or occupancy, salons characterized mainly as a 4. Billiard halls, pool rooms, low-rise, medium-rise or bowling alleys and golf clubhouses high-rise building/structure for 5. Dancing schools, disco pads, education-al, training and dance and amusement halls related activities, e.g., 6. Gymnasia, pelota courts and schools and related facilities sports complex and the like.

in the area 2. Colleges, universities, professional business schools, vocational and trade schools, technical schools and other institutions of higher learning 3. General hospitals, medical centers, multi-purpose clinics 4. Scientific, cultural and academic centers and research facilities except nuclear, radioactive, chemical and biological warfare facilities 5. Convention centers and related facilities 6. Religious structures, e.g., church, seminary, novitiates 7. Museums 8. Embassies/consulate 9. Student housing, e.g., dormitories, boarding house

Group D Institutional (Government and Health Services) Division D-1 1. Mental hospitals, mental GI (General Institutional) - a (Institutional, sanitaria and mental asylums community to national level of where personal 2. Police and fire stations, guard institutional use or occupancy, liberties of houses characterized mainly as a low-rise, inmates are 3. Jails, prisons, reformatories and medium-rise or high-rise restrained, correctional institutions building/structure for medical, or quarters of those 4. Rehabilitation centers government service administrative rendering public 5. Leprosaria and quarantine station and related activities, e.g., assistance and hospitals and related health care maintaining peace facilities, government offices, and order) military, police and correctional

1. Welfare homes, orphanages, boys and girls town, home for the aged and the like 2. Rehabilitation and vocational training center for ex-convicts, drug addicts, unwed mothers, physically, mentally and emotionally ex-sanitaria inmates; and similar establishments 3. Military camps/reservations/bases and training grounds

buildings and the like. 4. Penitentiary and correctional institution Division D-2 (Institutional, buildings for health care

Copyright 2010

1. 2.

Hospitals, sanitaria, and homes for the aged Nurseries for children of kindergarten age or non-ambulatory patients

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

72

accommodating more than five (5) persons Division D-3 1. (Institutional, for ambulatory patients 2. or children over

Nursing homes for ambulatory patients School and home, for children over kindergarten age

kindergarten age)

Orphanages

3.

Group EBusiness and Mercantile (Commercial) Division E-1 1. All uses allowed in Division jeepneys and taxis C-1 (Commercial One or Light (Business and B-1 (or for R-3 class) than six (6) units Commercial) - a neighborhood Mercantile, where buildings/structures or community level of commercial no work is done 2. Gasoline filling and service bus and trucks not use or occupancy, characterized except charge of stations. three (3) units in mainly as a low-rise parts and 3. Storage garage and boat building/structure maintenance storage. CHBs, gravel and for low intensity requiring no open 4. Commercial garages and other concrete commercial/trade, service flames, welding, parking buildings, display and business activities, e.g., or use of highly for cars, tractors, etc. one to three (1 to 3) storey flammable liquids) 5. Bus and railways depots shopping centers, small offices and terminals and offices or mixed-use/occupancy 6. Port facilities buildings and the like. 7. Airports and heliport facilities 8. At other types of transportation UTS (Utilities, Transportation complexes and Services) - a range of 9. All other types of large utilitarian/functional uses or complexes for public services occupancies, characterized 10. Pawnshops, money shops, mainly as a low-rise or photo and portrait studios, medium-rise building/structure shoeshine/repair stands, for low to high intensity retail drugstores, tailoring community support functions, and dress shops e.g., terminals/inter-modals/ 11. Bakeshops and bakery multi-modals and depots goods stores 12. Stores for construction supplies and building materials such as electrical and electronics, plumbing supplies, ceramic clay Copyright 2010

CD Technologies Asia, Inc.

1. Office building

1. Garage for

2. Office condominium

not greater

3. Department store/shopping center

in number

4. Bookstore and office supply shop

2. Garage for

5. Car shop

greater than

6. Home appliance store

number

7. Photo shop

3. Retailing of

8. Flower shop

sand and

9. Bakery and bake shop

products

10. Wine store 11. Grocery 12. Supermarket 13. Beauty parlor 14. Barber shop 15. Sauna bath and massage clinic 16. Dressmaking and tailoring shops 17. Movie house/theater 18. Playcourt, e.g., tennis, bowling, billiards 19. Swimming pool 20. Day/night club 21. Stadium, coliseum, gymnasium 22. Other sports and recreational establishments 23. Restaurants and other eateries 24. Short term special education like dancing schools, schools for self-defense, driving schools, speech clinics 25. Storeroom and warehouse

Philippine Laws Premium Edition 2009

73

cement and other similar products except CHBs, gravel and sand and other concrete products

26.

27.

28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. 41. 42. 43. 44.

45. 46. 47.

but only as may be necessary for the efficient conduct of the business Commercial housing like hotel, apartment, apartel, boarding house, dormitory, pension house, clubhouse, motel Commercial condominium (with residential units in upper floors) Embassy/consulate Library/museum Filing station/service station Clinic Vocational! technical school Convention center and related facilities Messengerial service Security agency Janitorial service Bank and other financial institution Radio and television station Building garage Commercial job printing Typing and photo engraving services Repair of optical instruments and equipment and cameras Repair of docks and watches Manufacture of insignia, badges and similar emblems except metal Transportation terminal/garage Plant nurseries Scientific, cultural and academic centers and research facilities except nuclear, radioactive, chemical and biological warfare facilities.

Division E-2 1. Wholesale and retail stores uses as colleges C-2 (Commercial Two or Business and 2. Shopping centers, malls universities, vocational and Mercantile in and supermarkets schools, general municipal or city level of nature) 3. Wet and dry markets specialized commercial use or 4. Restaurants, drinking and welfare, charitable and occupancy, characterized dining establishments with institutions mainly as a medium-rise less than one hundred (100) services and garage building/structure for occupancies. trucks, tow trucks, medium to high intensity 5. Day/night clubs, bars, cocktails, exceeding three commercial! trade, service sing-along lounges, bistros, storage facilities in and business activities, pubs, beer gardens commercial e.g., three to five (3 to 5) 6. Bakeries, pastry and bake shops. establishments storey shopping centers, 7. Office buildings and rentals, medium to large office or 8. Financial Institutions handicraft, accessory mixed use! occupancy Copyright 2010

CD Technologies Asia, Inc.

1. All uses in C-1 class buildings/structures may Medium Commercial) - a be allowed in C-2 class buildings/structures 2. Repair shops like house appliances, motor vehicles and accessory, home furnishing shops 3. Transportation terminal/garage with repair shops

1. Institutional and technical hospitals and general government 2. Hauling terminals for and buses not

4. Publishing

(3) units and

5. Medium scale junk shop

support of

6. Machinery display shop/center 7. Gravel and sand 8. Lumber/hardware

Philippine Laws Premium Edition 2009

4. Auto sales automotive

74

9. Printing & publishing plants parts shops, marine buildings/structures and and offices and sales yards the like. 10. Engraving, photo developing and scrap dealer shops printing shops SPE (Special) - other vertical 11. Photographer and painter studios, facilities not mentioned under tailoring and haberdashery shops regular uses/occupancies of 12. Factories and workshops, using buildings/structures such as less flammable or non-combustible cemeteries, memorial parks materials and the like 13. Battery shops and repair shops 14. Paint stores without bulk handling 15. Funeral parlors 16. Memorial and mortuary chapels, crematories 17. Columbarium 18. Telephone and telegraph exchanges 19. Telecommunications, media and public information complexes including radio and TV broadcasting studios 20. Cell (mobile) phone towers 21. Battery shops and auto repair shops 22. Bakeries, pastry and bake shops 23. Police and fire stations 24. Glassware and metalware stores, household equipment and appliance shops 25. Manufacture of insignia, badges and similar emblems except metal 26. General retail establishments such as curio or antique shops, pet shops and aquarium stores, bookstores, art supplies and novelties, jewelry shops, liquor wine stores and flower shops 27. Employment/recruitment agencies, news syndicate services and office equipment and repair shops and other offices 28. Watch sales and services, locksmith and other related services 29. Other stores and shops for conducting retail business and local shopping establishments 30. Radio, television and other electrical appliance repair shops 31. Furniture, repair and upholstering job 32. Computer stores and video shops, including repair 33. Internet cafes and cyber stations 34. Garment manufacturing with no more than twenty (20) machines 34. Signboard and streamer painting and silk screening 35. Car barn for jeepneys and taxis not more than six (6) units 36. Lotto terminals, off-fronton, on-line bingo outlets and off track betting stations 37. Gardens and landscaping supply/contractors Copyright 2010

CD Technologies Asia, Inc.

9. Manufacture of ice, ice blocks, cubes, tubes, crushed 10. Manufacture of signs and

and spare craft, aircraft 5. Junk shops,

advertising displays (except printed) 11. Chicharon factory 12. Welding shops 13. Machine shops service operations (repairing/rebuilding, or custom job orders) 14. Motorcycles/bicycles repair shops 15. Lechon stores 16. Biscuit factory - manufacture of biscuits, cookies, crackers and other similar dried bakery products 17. Doughnut and hopia factory 18. Factory for other bakery products not elsewhere classified (n e.c ) 19. Shops for repack in of food products e.g. fruits, vegetables, sugar and other rated products 20. Funeral parlors, mortuaries and crematory services and memorial chapels 21. Parking lots, garage facilities 22. Buildings/structures for other commercial activities not elsewhere classified (n.e c.)

Philippine Laws Premium Edition 2009

75

38. Printing, typesetting, copiers and duplicating services 39. Photo supply and developing 40. Restaurants, canteens, eateries, delicatessen shops, confectionery shops and automats/fastfoods 41. Groceries 42. Laundries and laundromats 43. Recording and film laboratories 44. Auto repair, tire, vulcanizing shops and carwash with minimum 100 sq. meters service area 45. Physical fitness gyms/centers Division E-3 1. All permitted uses in C-3 (Commercial Three or (Business and Division E-1 (or for C-1 and Metropolitan Commercial) Mercantile, where C-2 class) building/structures means a metropolitan level no repair work is 2. Aircraft hangars of commercial use/occupancy, done except 3. Commercial parking lots and characterized mainly as a exchange of parts garages medium-rise to high-rise and maintenance 4. Department stores, shopping building/structure for high requiring no open malls/centers, commercial to very high intensity flames, welding and sports complexes/areas commercial/trade, service or use of highly 5. Institutional uses as university and business activities, flammable liquid) complexes e.g., large to very large 6. Other commercial! business shopping malls, very activities not elsewhere large office or classified (n.e.c.) mixed-use/occupancy

1. All uses allowed in R-1, R-2 and R-3 Zones 2. All uses allowed in C-1, C-2 and C3 Zones 3. Some uses allowed in I-1 Zones 4. All uses allowed in GI Zones and SI Zones 5. Parks and Recreation and Entertainment class buildings/structures

buildings and the like. Group F(Non-Pollutive/ Non-Hazardous Industries and Non-Pollutive Hazardous Industries) Division F1 1. Ice plants and cold storage with lesser I-1 (Industrial One) - a light (Light industrial) buildings environmental impactindustrial use or occupancy, 2. Power plants (thermal, hydro characterized mainly as or geothermal) a low-rise but sprawling 3. Pumping plants (water supply, building/structure for low storm drainage, sewerage, intensity manufacturing irrigation and waste treatment or production activities. Copyright 2010

CD Technologies Asia, Inc.

Customary support facilities

Building/structure

for industries such as housing,

negative

community, utilities and services

Philippine Laws Premium Edition 2009

76

4. 5. 6. 7.

plants) Dairies and creameries Rice mills and sugar centrals Breweries, bottling plants, canneries, and tanneries Factories and workshops using incombustible or non-explosive materials

Group G Storage and Hazardous Industrial (Pollutive/ Non-Hazardous Industries and Pollutive/Hazardous Industries Only) Division G1 1. Storage tanks, buildings for storing Customary support facilities with lesser I-2 (Industrial Two) - a medium (Medium Industrial, gasoline, acetylene, LPG, calcium, for industries such as housing, environmental impactindustrial use or occupancy, which shall include carbides, oxygen, hydrogen, and community, utilities and services characterized mainly as a storage and the like low-rise but sprawling handling of 2. Armories, arsenals and munitions building/structure for medium hazardous and factories intensity manufacturing or highly flammable 3. Match and fireworks factories production activities. materials) 4. Plastics resin plants (monomer and polymer) UTS (Utilities, Transportation 5. Plastics compounding and and Services) - a range of processing plants utilitarian/functional 6. Acetylene and oxygen generating uses/occupancies, plants characterized mainly by 7. Cooking oil and soap processing low-rise or medium-rise plants buildings/structures for 8. Factories for highly flammable low to high intensity chemicals community support functions, 9. Water and power e.g., power and water generation/distribution generation/distribution complexes facilities, telecommunication 10. Liquid and solid waste facilities, drainage wastewater management facilities and sewerage facilities, 11. All other types of large solid waste handling facilities complexes for public and the like excluding utilities terminals/inter-modals/

Building/structure negative

multi-modals and depot Division G-2 1. with lesser (Medium Industrial 2. environment impact buildings for storage and handling 3. Copyright 2010

All uses permitted in I-1 class

Customary support facilities

Building/structure

Dry cleaning plants using

for industries such as housing,

negative

flammable liquids Paint stores with bulk handling

community, utilities and services

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

77

of flammable materials)

Division G-3 with lesser (Medium Industrial environment impact buildings for wood working activities, papers cardboard manufactures, textile and garment factories)

4.

Paint shops and spray painting rooms

5.

Sign and billboard painting shops

1.

Wood working establishments,

Customary support facilities

Building/structure

lumber and lumber yards

for industries such as housing,

negative

2. 3. 4. 5. 6. 7. 8. 9.

Planing mills and sawmills, community, utilities and services veneer plants Wood drying kilns Pulp, paper and paperboard factories Wood and cardboard box factories Textile and fiber spinning mills Grains and cement silos Warehouses where highly combustible materials are stored. Factories where loose combustible fiber or dirt are manufactured, processed or generated.

10. Garment and undergarment factories Division G-4 1. with lesser (Medium Industrial, 2. environment impact for repair garages and engine

Repair garages and shops

Customary support facilities

Building/structure

Factories for engines and

for industries such as housing,

negative

turbines and attached testing facilities

community, utilities and services

Hangars

Customary support facilities

Building/structure

Manufacture and assembly

for industries such as housing,

negative

plants of aircraft engine Repairs and testing shops

community, utilities and services

manufacture) Division G-5 1. with lesser (Medium Industrial, 2. environment impact for aircraft facilities) 3.

for aircraft engines and parts Group HAssembly for less than 1,000 (Cultural and/or Recreational) Division H-1 1. Theaters and auditoriums PRE (Park Structures, (Recreational, 2. Concert halls and open houses Recreation and Entertainment) which are assembly 3. Convention halls a range of recreational uses or buildings with 4. Little theaters, audio-visual rooms occupancies, characterized mainly stage and having as a low-rise or medium-rise an occupant load building/structure for low to of less than 1,000) medium intensity recreational or entertainment functions related to educational uses, e.g., structures on campuses or its component parks/open Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

78

spaces and all other kinds of recreational or assembly buildings/structures on campus such as auditoria, mess halls, seminar facilities, gymnasia, stadia, arenas and the like.

CUL (Cultural) - a community to national level of cultural use or occupancy, characterized mainly as a low-rise or medium rise building/structure for cultural activities, e.g., cultural centers, convention centers, very large office or mixed-use/occupancy buildings and the like. Division H-2 (Recreational, which are assembly buildings with stage and having an occupant load

1. 2. 3.

Dance halls, cabarets, ballrooms Skating rinks Cockfighting arenas

of 300 or more) Division H-3 1. (Recreational, 2. which are assembly buildings with stage and having an occupant load

Dance halls, ballrooms Skating rinks

of less than 300) Division H-4 (Recreational, tourism estate developments or tourism-oriented establishments, which are structures not included in

1. 2. 3. 4. 5. 6. 7. 8.

Sports stands Reviewing stands Grandstand and bleachers Covered amusement parks Boxing arenas, jai-alai stadiums Race tracks and hippodromes All types of resort complexes All other types of amusement and entertainment complexes

Division H-1) Group IAssembly for More than 1,000 Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

79

(Cultural and/or Recreational) Division I-1 1. Colisea and sports complexes CUL (Cultural) - a community (Recreational, 2. Theaters and convention centers to national level of cultural use Assembly Buildings 3. Concert halls and open houses or occupancy, characterized with stage and 4. Convention centers mainly as a low-rise or an occupant medium-rise building/structure load of 1,000 for cultural activities or more in the building) PRE (Park Structures, Recreation

1. Parks/gardens 2. Resort areas, e.g., beaches, including accessory uses 3. Open air or outdoor sports activities and support facilities, including low rise stadia, gyms, amphitheaters and swimming pools 4. Golf courses, ball courts, race

and Entertainment) - a range of tracks and similar uses recreational uses or occupancies, 5. Memorial/Shrines/monuments, characterized mainly as a low-rise kiosks and other park structures or medium-rise building/structure 6. Sports Club for low to medium intensity 7. Underground parking recreational or entertainment structures/facilities functions related to educational uses, e.g., structures on campuses or its component parks/open spaces and all other kinds of recreational or assembly buildings/structures on campus such as auditoria, mess halls, seminar facilities, gymnasia, stadia, arenas and the like. Group J Accessory (Agricultural and Other Occupancies/Uses not Specifically Mentioned Under Groups A through I) Division J-1 1. Agricultural structures: A (Agricultural) - an agricultural a. Sheds or agriculture-related use or b. Barns occupancy, characterized mainly c. Poultry, houses as a low-rise or medium-rise d. Piggeries Copyright 2010

CD Technologies Asia, Inc.

1. Cultivation, raising and growing of staple crops such as rice, corn, camote, cassava and the like 2. Growing of diversified plants

Philippine Laws Premium Edition 2009

80

building/structure for low to high e. Hatcheries intensity agricultural or related f. Stables activities, e.g., poultry houses, g. Greenhouses hatcheries, piggeries, greenhouses h. Granaries granaries and the like as well as i. Silos offices, educational, training,

and trees, such as fruit and flower bearing trees, coffee, tobacco, etc. 3. Silviculture, mushroom culture, fishing and fish culture, snake culture, crocodile farm, monkey

research and related facilities raising and the like for agriculture and the like. 4. Customary support facilities such as palsy dryers and rice AI (Agro-industrial) - an agrothreshers and storage barns industrial or related use or and warehouses occupancy, characterized mainly 5. Ancillary dwelling units/farmhouses as a low-rise building/structure for tillers and laborers for low to high intensity 6. Agricultural research and agro-industrial or related experimentation facilities activities to include offices, such as breeding stations, fish educational, training, research farms, nurseries, demonstration and related facilities for farms, etc. agro-industry. 7. Pastoral activities such as goat-raising and cattle fattening 8. Home occupation for the practice of one's profession or engaging home business such as dressmaking, tailoring, baking, running a sari-sari store and the like, provided that, the number of persons engaged in such business/industry shall not exceed five (5), inclusive of the owner there shall be no change in the outside appearance of the building premises; no home occupation shall be conducted in any customary accessory uses cited above; no traffic shall be generated by such home occupation in greater volume than would normally be expected in a residential neighborhood and any need for parking generated by the conduct of such home occupation shall be met off the street in a place other than the required front yard; no equipment or process shall be used in such occupation which creates noise, vibration, glare, tunes, odors and electrical interference detectable to the normal senses and visual or audible interference in any radio or television receiver or causes fluctuations in line voltage of the premises. 9. Home industry classified as cottage Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

81

10.

11. 12. 13.

14. 15. 16. 17. 18.

19. 20. 21. 22. 23. 24. 25. 26.

27. 28.

29. 30. 31.

32. 33.

34. 35. 36. 37.

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

industry, e.g., mat weaving, pottery making, food preservation, etc. provided that such home industry shall not occupy more than 30% of floor area of the dwelling unit there shall be no change or alteration in the outside appearance of the dwelling unit and shall not be a hazard or nuisance; allotted capitalization shall not exceed the capitalization as set by the Department of Trade and Industry (DTI); such shall consider same provisions as enumerated in Home Occupation, this Section. Backyard raising of livestock and fowl, provided that for livestock- a maximum of 10 heads; for fowl. a maximum of 500 birds All uses allowed in agriculture Rice/corn mills (single pass) Drying, cleaning ring and preserving of meat and its by products and derivatives Drying, smoking and airing of tobacco Flour mill Cassava flour mill Manufacture of coffee Manufacture of unprepared animal feeds, other grain milling, n.e.c. Production of prepared feeds for animals Cigar and Cigarette factory Curing and redrying tobacco leaves Miscellaneous processing of tobacco leaves, n.e.c. Weaving hemp textile Jute spinning and weaving Manufacture of charcoal Milk processing plants (Manufacturing filled, reconstituted or recombined milk, condensed or evaporated) Butter and cheese processing plants Natural fluid milk processing (pasteurizing, homogenizing, vitaminizing, bottling of natural animal milk and cream related products) Other dairy products, n.e.c. Canning and preserving of fruits and fruit juices Canning and preserving of vegetables and vegetable juices Canning and preserving of vegetable sauces Miscellaneous canning and preserving of fruit and vegetables, n.e.c. Fish canning Patis factory Bagoong factory Processing, preserving and canning of fish and other 82

seafoods, n.e.c. 38. Manufacturing of desiccated coconut 39. Manufacture of starch and its products 40. Manufacture of wines from juices of local fruits 41. Vegetable oil mills, including coconut oil 42. Sugarcane milling (centrifugal and refines) 43. Sugar refining 44. Muscovado sugar mill 45. Cotton textile mill 46. Manufacture/processing of other plantation crops, e.g., pineapple, bananas, etc. 47. Other commercial handicrafts and industrial activities utilizing plant or animal parts and/or products as raw materials, n.e.c. 48. Other accessory uses incidental to agro-industrial activities Division J-2 1. Private garages, carports uses/occupancy permitted in (Accessory) 2. Towers, smokestacks and Divisions (or classes of - refers to land development or chimneys buildings/structures) if such 3. Swimming pools including uses/occupancy are part of the shower and locker room Development (PUD) said project site must have a 4. Fence over 1.80 meters high, Comprehensive Development separate fire walls Master Plan (CDMP) or its 5. Steel and/or concrete tanks acceptable equivalent, i.e., a

1. All PUD (Planned Unit Development) all other

redevelopment schemes for a new or built-up project site wherein Planned Unit

unitary development plan/site plan that permits flexibility in planning/urban design, building/structure siting, complementarity of building types and land uses, usable open spaces for general public use services and

Business activities and the preservation of significant natural land features if feasible, whereby said CDMP must be duly approved by the

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

83

LGU concerned. Division J-3

1. 2. 3. 4. 5.

Stages, platforms and similar structures Pelota, tennis, badminton or basketball courts Tombs, mausoleums and niches Aviaries and aquariums and zoo structures Banks and record vaults

SECTION 702.

Change in Use. —

No change shall be made in the character of occupancy or use of any building which would place the building in a different division of the same group of occupancy or in a different group of occupancies, unless such building is made to comply with the requirements of the Code for such division or group of occupancy. The character of occupancy of existing buildings may be changed subject to the approval of the Building Official and the building may be occupied for purposes set forth in other Groups: Provided the new or proposed use is less hazardous, based on life and fire risk, than the existing use. SECTION 703. 1.

Mixed Occupancy. —

General Requirements When a building is of mixed occupancy or used for more than one occupancy, the whole building shall be subject to the most restrictive requirement pertaining to any of the type of occupancy found therein except in the following:

2.

a.

When a one-storey building houses more than one occupancy, each portion of the building shall conform to the requirement of the particular occupancy housed therein and;

b.

Where minor accessory uses do not occupy more than 10% of the area of any floor or a building, nor more than 10% of the basic area permitted in the occupancy requirements, in which case, the major use of the building shall determine the occupancy classification.

Forms of Occupancy Separation Occupancy separations shall be vertical or horizontal or both, or when necessary, of such other forms as may be required to afford a complete

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

84

separation between the various occupancy divisions in the building. 3.

Types of Occupancy Separation Occupancy separation shall be classified as "One-Hour Fire-Resistive", "Two Hour Fire-Resistive", "Three-Hour Fire-Resistive" and "Four-Hour Fire-Resistive." AICDSa

4.

Copyright 2010

a.

A "One-Hour Fire-Resistive Occupancy Separation" shall be of not less than one-hour fire-resistive construction. All openings in such separation shall be protected by a fire-assembly having a one-hour fire-resistive rating.

b.

A "Two-Hour Fire-Resistive Occupancy Separation" shall be of not less than two-hour fire-resistive construction. All openings in such separation shall be protected by a fire assembly having a two-hour fire-resistive rating.

c.

A "Three-Hour Fire-Resistive Occupancy Separation" shall be of not less than three-hour fire-resistive construction. All openings in walls forming such separation shall be protected by a fire assembly having a three-hour fire-resistive rating. The total width of all openings in any three-hour fire-resistive occupancy separation wall in any one-storey shall not exceed 25% of the length of the wall in that storey and no single opening shall have an area greater than 10.00 sq. meters. All openings in floors forming a "Three-Hour Fire-Resistive Occupancy Separation" shall be protected by vertical enclosures extending above and below such openings. The walls of such vertical enclosures shall be of not less than two-hour fire-resistive construction, and all openings therein shall be protected by a fire assembly having a three-hour fire-resistive rating.

d.

A "Four-Hour Fire-Resistive Occupancy Separation" shall have no openings therein and shall be of not less than four-hour fire-resistive construction.

Fire Rating for Occupancy Separation

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

85

Occupancy Separations shall be provided between groups, subgroupings, or divisions of occupancies. The Secretary shall promulgate rules and regulations for appropriate occupancy separations in buildings of mixed occupancy; Provided, that, where any occupancy separation is required, the minimum shall be a "One-Hour Fire-Resistive Occupancy Separation"; and where the occupancy separation is horizontal, structural members supporting the separation shall be protected by an equivalent fire-resistive construction. aSHAIC

SECTION 704. 1.

2.

Location on Property. —

General a.

No building shall be constructed unless it adjoins or has direct access to a public space, yard or street on at least one of its sides.

b.

For the purpose of this Section, the centerline of an adjoining street or alley shall be considered an adjacent property line.

c.

Eaves over required windows shall not be less than 750 millimeters from the side and rear property lines.

Fire Resistance of Walls Exterior walls shall have fire resistance and opening protection in accordance with the requirements set forth by the Secretary. Projections beyond the exterior wall shall not exceed beyond a point one-third the distance from an assumed vertical plane located were the fire-resistive protection of openings is first required to the location on property whichever is the least restrictive. Distance shall be measured at right angles from the property line. When openings in exterior walls are required to be protected due to distance from property line, the sum of the areas of such openings in any storey shall not exceed 50% of the total area of the wall in that storey. HTcADC

3.

Buildings on Same Property and Buildings Containing Courts For the purpose of determining the required wall and opening protection, buildings on the same property and court walls shall be assumed to have a property line between them. When a new building is

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

86

to be erected on the same property with an existing building, the assumed property line from the existing building shall be the distance to the property line for each occupancy as set forth by the Secretary; Provided, that two or more buildings on the same property may be considered as one building if the aggregate area of such building is within the limits of allowable floor areas for a single building, and when the buildings so considered, house different occupancies or are of different types of construction, the area shall be that allowed for the most restrictive occupancy or construction; 4.

Building Footprint and Firewall Requirements a.

The following rules shall be observed in the determination of the Allowable Maximum Building Footprint (AMBF) for buildings and related habitable structures. If the stated rules are compared with (1) Rule VIII Table VIII.1. Reference Table on Percentage of Site Occupancy and Maximum Allowable Construction Area (MACA); (2) Rule VIII Tables VIII.2. and VIII.3. (setbacks, yards and courts; or (3) with the applicable stipulations under this Rule and with the applicable stipulations of the Fire Code, the more stringent but applicable regulation out of the aforementioned rules should be observed;

b.

If without a firewall, the footprint of a proposed building/structure shall be measured horizontally from the property line to the outermost faces of the exterior walls of the building/structure; Provided, that the distance measured from the proper line shall conform with the applicable stipulations of this Rule and Rule VIII; The resultant area established at grade level upon which the proposed building/structure may stand shall be the AMBF;

c.

Footprint Based on Firewall Provisions i. If with a firewall on one (1) side, the footprint of a proposed building/structure shall be measured horizontally from the property line with a firewall to the outermost faces of the opposite exterior walls of the building/structure; Provided, that the applicable

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

87

stipulations of the Fire Code are strictly followed;

cISDHE

ii. If with a firewall on two (2) sides or on one (1) side and the rear property line, the footprint of a proposed building/structure shall be measured horizontally from the opposing property lines in case of a firewall on two (2) sides or from the rear property line with a firewall to the outermost faces of the opposite exterior walls of the building/structure; provided, that the applicable stipulations of the Fire Code are strictly followed; iii. Absolutely no firewalls are allowed for a low density residential (R-1) uses or occupancies; an abutment of up to 3.20 meters from established grade level may however be permitted but solely for the purpose of supporting a carport roof; provided further that such abutment shall be constructed of perforated or decorative concrete blocks above 1.50 meters measured vertically from the established grade level; such an abutment shall not be longer than 7.00 meters or 50% of the side property line in total length, whichever is shorter. iv. For medium density residential (R-2) uses or occupancies, a firewall can be erected on a maximum of 80% of the total length of a side property line; provided that only one (1) side property line is used for a firewall in the case of a R-2 structure; and provided further that the applicable stipulations of the Fire Code are strictly followed; v. For high-density residential (R-3) uses or occupancies, two (2) types of firewall construction may be permitted: (a) For a R-3 use or occupancy with a firewall on two (2) sides, a firewall can be erected on a maximum of 85% of the total length of each side property line; provided that all firewall construction shall not exceed 65% of the total perimeter of the R-3 property, i.e., total length of all property lines; provided that firewalls in R-3 lots shall only be allowed for a maximum two (2) Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

88

storey component structure; and provided further that all the applicable stipulations of the Fire Code are strictly followed; and aTSEcA

(b) For a R-3 use or occupancy with a firewall on one (1) side property line and at the rear property line, a firewall can be erected on a maximum of 90% of the total length of the side and rear property lines and up to 100% in case the rear property line is only 4.00 meters wide; provided that all firewall construction at the side property lines shall not exceed 50% of the total perimeter of the R-3 property, i.e., total length of all property lines; provided that firewalls in R-3 lots shall only be allowed for a maximum two (2) storey structure but not at the rear property line where the maximum allowed firewall height shall only be 3.20 meters measured vertically from established grade; and provided further that all the applicable stipulations of the Fire Code are strictly followed. llcd

vi. For townhouse residential (R-4) uses or occupancies, firewalls on the two (2) sides of each townhouse unit may be permitted; the R-4 firewall can be erected on a maximum of 85% of the total length of each side property line; provided that all firewall construction shall not exceed 50% of the total perimeter of each R-4 property, i.e., total length of all property lines; provided that firewalls in each R-4 use or occupancy shall be allowed for a maximum three (3) storey structure; and provided further that all the applicable stipulations of the Fire Code are strictly followed; vii. For residential condominium (R-5) uses or occupancies, two (2) types of firewall construction may be permitted: (a) For a R-5 use or occupancy with a firewall on two (2) sides, a firewall can be erected on a maximum of 75% of the total length of each side Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

89

property line; provided that all firewall construction at the side property lines shall not exceed 50% of the total perimeter of the R-5 property, i.e., total length of all property lines; provided that side firewalls in R5 uses or occupancies shall only be allowed for a maximum eight (8) storey component structure, i.e., the podium; and provided further that all the applicable stipulations of the Fire Code are strictly followed; and TCAHES

(b) For a R-5 use or occupancy with a firewall on one (1) side and at the rear property line, a firewall can be erected on a maximum of 65% of the total length of the side property line and on a maximum of 50% of the total length of the rear property line; provided that all firewall construction shall not exceed 60% of the total perimeter of the R-5 property, i.e., total length of all property lines; provided that the side firewalls in R-5 uses or occupancies shall only be allowed for a maximum eight (8) storey component structure and that at the rear property line, the maximum allowed firewall height shall only be 14.00 meters measured vertically from established grade; and provided further that all the applicable stipulations of the Fire Code are strictly followed. cHEATI

viii. All existing openings on all firewalls shall be sealed completely to maintain the fire integrity of adjoining buildings/structures. ix. The provision of a fully functional sprinkler system and the installation of other fire-retardant or fire suppression devices in the case of commercial, institutional and industrial buildings/structures may allow firewall construction for up to 70% of the total perimeter of the property lines provided that the prescribed setbacks, yards and courts fronting the Road Right-Of-Way (RROW) are first fully complied with; and provided further that all the applicable stipulations Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

90

of the Fire Code, particularly on the number, type and locations of fire exits are strictly followed. SECTION 705.

Allowable Floor Areas. —

1.

General. The Allowable Maximum Total Gross Floor Area (TGFA) of any proposed building/structure shall only be as allowed under this Rule.

2.

TGFA Limitation. In Table VII.1. hereafter, the percentages (%) indicated in the third (3rd) through eighth (8th) columns, but excluding the multiplier numbers 3, 5, 12, 18, and 30 (which represent the number of storeys/floors), are the percentages of the Total Lot Area (TLA) that may be used to initially determine the Allowable Maximum TGFA for a proposed building/structure.

3.

Cross-check of TGFA with Allowable Maximum Volume Building (AMVB). The Allowable Maximum TGFA once established must be thoroughly cross-checked with the AMVB to find out if the AMVB is not exceeded. If exceeded, the necessary adjustments on the Maximum Allowable TGFA must be made since the AMVB must always prevail.

Table VII.1. Allowable Maximum Total Gross Floor Area (TGFA) Based on the Allowed Percentage of Site Occupancy (PSO) of the Total Lot Area (TLA) Allowable Maximum Total Gross Floor Area (TGFA)* by Type/Location of Lot Character of Use/ Occupancy

Type of Building

* Note Building Height Limit (BHL) multiplied by the Allowable Maximum Building Footprint (AMBF) expressed as a percentage (%) of the Total Lot Structure Area or TLA (with or without firewall). Figure subject to reduction to comply with the floor area component of the Allowable Maximum Volume of Building (AMVB). Refer to Table VII.1. to arrive at the percentage (%) of TLA. Interior (or Rear) Lot and End Lot (see Fig. VIII.8. and VIII.5.14. of Rule VIII)

Inside (or Regular) Lot (see Fig. VIII.9. of Rule VIII)

Corner Lot

Through Lot

(see Fig. VIII.10. of Rule VIII)

(see Fig. VIII.11. of Rule VIII)

CornerThrough Lot

Corner Lot Abutting 3 or More Streets, etc. Rivers, Etc. (see Fig. VIII.13. of

(see Fig. VIII.12. of Rule VIII)

Rule VIII)

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

91

Residential GROUP A-I

Residential TLA

3 x 70% TLA

3 x 70% of TLA

3 x 70% TLA

3 x 70% TLA

3 x 60%

3 x 70%

3 x 70%

3 x 70%

3 X 70%

5 x 70%

5 X 60%

5 X 70%

5 X 70%

5 x 70%

5 x 70%

3 x 70%

3 x 70%

3 x 70%

3 x 70%

3 x70%

3 x70%

12 x 80%

12 x 80%

12 x 80%

12 X 80%

12 x 80%

12 x 80%

3 x 80%

3 x 80%

3 x 80%

3 x 80%

3 x 80%

3 x 80%

3 x 80%

3 x 80%

3 x 80%

3 x 80%

3 x 80%

3 x 80%

18 x 80%

18 x 80%

18 x 80%

18 x 80%

18 x 80%

18 x 80%

Residential (R-1)

Not applicable (NA)

NA

NA

NA

NA

NA

Basic Residential

3 x 75%

3 x 70%

3 x 75%

3 x 75%

3 x 75%

3 x 75%

5 x 75%

5 x 70%

5 x 75%

5 x 75%

5 x 75%

5 x 75%

3 x 80%

3 x 80%

3 x 80%

3 x 80%

3 x 80%

3 x 80%

12 x 80%

12 x 80%

12 x 80%

12 x 80%

12 x 80%

12 x 80%

3 x 80%

3 x 80%

3 x 80%

3 x 80%

3x80%

3 x 80%

firewalls) Basic Residential

3 (floors/ 1 storeys) (R-1)

3 x 50% of TLA x 60% of

(without

TLA

3 x 70%

2(R-2) Maximum Residential 2(R-2) Basic Residential 3(R-3) Maximum Residential 3(R-3) Residential 4(R-4)/Individual Townhouse Lots/Units Residential 4(R-4)//Individual Townhouse Lots/Units Residential 5(R-5)/ Condominiums Residential GROUP A-I (with firewalls)

2(R-2) Maximum Residential 2 (R-2) Basic Residential 3(R-3) Maximum Residential 3(R-3) Residential Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

92

4(R-4)/Individual Townhouse Lots/Units Residential 5(R-5)/

18 x 80%

18 x 80%

18 x 80%

18 x 80%

18 x 80%

18 x 80%

Commercial 1 (Com-1)

5 x 80%

5 x 75%

5 x 80%

5 x 80%

5 x 90%

5 x 90%

Commercial 2

12 x 80%

12 x 75%

12 x 80%

12 x 80%

12 x 90%

12 x 90%

30 x 80%

30 x 75%

30 x 80%

30 x 80%

30 x 90%

30 x 90%

5 x 85%

5 x 85%

5 x 90%

5 x 90%

5 x 95%

5 x 95%

12 x 85%

12 x 85%

12 x 90%

12 x 90%

12 x 95%

12 x 95%

30 x 85%

30 x 85%

30 x 90%

30 x 90%

30 x 95%

30 x 95%

Duly-approved Building Height Limit (BHL) x 80% of

BHL x 75% of TLA

BHL x 80% of TLA

BHL x 80% of TLA

BHL x 90% of TLA

BHL x 90% of TLA

Condominiums Commercial GROUPS B, C, E, H, I

(Com-2) Commercial 3 (Com-3) Commercial 1 (Com-1) with Sprinkler System & Firewalls Commercial 2 (Com-2) with Sprinkler System & Firewalls Commercial 3 (Com-3) with Sprinkler System & Firewalls Industrial GROUPS F, G

Industrial 1 (Ind.1)

TLA Industrial 2

BHL

BHL

BHL

BHL

BHL

BHL

(Ind-2)

x 80%

x 75%

X 80%

x 80%

X 90%

X 90%

Industrial 3

BHL

BHL

BHL

BHL

BHL

BHL

(Ind-3)

x 80%

x 75%

x 80%

x 80%

x 90%

x 90%

Industrial 1 (Ind-1) with Sprinkler System &

BHL x 85%

BHL x 85%

BHL x 90%

BHL x 90%

BHL x 95%

BHL x 95%

BHL x 85%

BHL x 85%

BHL x 90%

BHL x 90%

BHL x 95%

BHL x 95%

Firewalls Industrial 2 (l-2) with Sprinkler Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

93

System & Firewalls Industrial 3 (Ind-3) with Sprinkler

BHL x 85%

BHL x 85%

BHL x 90%

BHL x 90%

BHL x 95%

BHL x 95%

Without Sprinkler System &

BHL x 50%

BHL x 50%

BHL x 60%

BHL x 60%

BHL x 60%

BHL x 60%

Firewalls

of TLA

of TLA

of TLA

of TLA

of TLA

of TLA

With Sprinkler System &

BHL x 60%

BHL x 60%

BHL x 70%

BHL x 70%

BHL x 70%

BHL x 70%

Firewalls

of TLA

of TLA

of TLA

of TLA

of TLA

of TLA

Without Sprinkler System &

BHL x 60%

BHL x 60%

BHL x 65%

BHL x 65%

BHL x 65%

BHL x 65%

Firewalls

of TLA

of TLA

of TLA

of TLA

of TLA

of TLA

With Sprinkler System &

BHL x 70%

BHL x 70%

BHL x 70%

BHL x 70%

BHL x 70%

BHL x 70%

Firewalls

of TLA

of TLA

of TLA

of TLA

of TLA

of TLA

Without Sprinkler System &

BHL x 50%

BHL x 50%

BHL x 60%

BHL x 60%

BHL x 60%

BHL x 60%

Firewalls

of TLA

of TLA

of TLA

of TLA

of TLA

of TLA

With Sprinkler System &

BHL x 60%

BHL x 60%

BHL x 70%

BHL x 70%

BHL x 70%

BHL x 70%

Firewalls Institutional GROUP D

Cultural

Transportation

Firewalls Note: Maximum of sixty (60) storeys (180.00 meters) BHL for inland areas not close to airports.

SECTION 706.

Allowable Floor Area Increases. —

The floor areas hereinabove provided may be increased in certain specific instances and under appropriate conditions, based on the existence of public space, streets or yards extending along and adjoining two or more sides of the building or structure subject to the approval of the Building Official. (Refer to Guidelines on Determining Gross Floor Area and Total Gross Floor Area of a Building/Structure at the end of this Rule) SECTION 707. 1.

Copyright 2010

Maximum Height of Buildings. —

The maximum height and number of storeys of proposed building shall be dependent upon the character of use or occupancy and the type of construction, considering end-user

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

94

population density, light and ventilation, width of RROW/streets particularly of its roadway/carriageway component, building bulk, off-street cum off-site parking requirements, etc. and in relation to local land use plan and zoning regulations as well as other environmental considerations, e.g., geological, hydrological, meteorological, topographical, prevailing traffic conditions, the availability and capacity of public utility/service systems, etc. (Refer to Guidelines on Building Bulk at the end of this Rule) aDcHIS

2.

Determination of Building Height: a.

BUILDING HEIGHT LIMIT (BHL) — the maximum height to be allowed for buildings/structures based on their proposed use or occupancy; the BHL is generally determined after the application of other development controls (DC) and certain other parameters, i.e., considerations of site conditions, view, etc. (Table VII.2. of this Rule). The BHL shall be generally measured from the established grade line to the topmost portion of the proposed building/structure. If applicable, the BHL may be subject to clearance requirements of the Air Transportation Office (ATO) or of the concerned military/security authorities. (Refer to Guidelines on Development Controls at the end this Rule) BHL excludes the height of permitted/allowed projections above the roof of the building/structure, e.g., signage, mast, antenna, telecom tower, beacons and the like.

b.

The Building Height Limit (BHL) of any proposed building/structure shall only be as allowed under this Rule (as shown in table below) or under the duly approved city/municipal (local) zoning ordinance, whichever is more restrictive.

Table VII.2. Building Height Limit (BHL) by Type of Use or Occupancy Building Height Limit (BHL) Character of Use or Occupancy

1.

Residential

Copyright 2010

CD Technologies Asia, Inc.

Type of Building/Structure

Residential 1 (R-1) Philippine Laws Premium Edition 2009

Number of Allowable storeys/floors above

Meters above highest

established grade

grade

3

10.00 95

Residential 2 (R-2) a. Basic b. Maximum Residential 3 (R-3) a. Basic b. Maximum Residential 4 (R-4)/

3 5

10.00 15.00

3 12

10.00 36.00

3

10.00

Commercial 1 (C-1) Commercial 2 (C-2)

3-5 6

10.00-15.00 18.00

Commercial 3 (C-3)

16-60

48.00-180.00

Townhouses

(Individual lots/units) Residential 5 (R-5)/ 12-18

36.00-54.00

Condominiums 2.

3.

Commercial

Industrial

Industrial 1 (I-1) Industrial 2 (1-2) Industrial 3 (1-3)

4.

Institutional

-

5.

Cultural

-

6.

Utility/Transportation/ RROW/Services Parks and Open Recreational and Entertainment Spaces Agricultural/Agro-Industrial/Tourism

-

7.

8.

-

-

15.00 meters but not exceed the duly-approved BHL in the major zone it is part of 21.00 meters but not exceed the duly-approved BHL in the major zone it is part of 27.00 meters but not exceed the duly-approved BHL in the major zone it is part of) 15.00 meters (or must follow the duly-approved BHL in the major zone it is part of) 30.00 meters (or must follow the duly-approved BHL in the major zone it is part of) 15.00 meters (or must complement the duly-approved BHL in the major zone it is part of) 15.00 meters (or must complement the duly-approved BHL in the major zone it is part of) 15.00 meters (or must complement the duly-approved BHL in the major zone it is part of)

9.

Planned Unit Development (PUD)

PUD at a reclamation area close to an operating airport PUD at a reclamation area PUD at a coastal area PUD at an inland area close to an operating airport PUD at an inland area

3-15

10.00-45.00 (with ATO-prescribed BHL as needed)

3-30 16-45 3-25

10.00-30.00 48.00-135.00 10.00.75.00 (with ATO-prescribed BHL as needed)

12-60

36.00-180.00

Notes: a.

Establishing Grade -

Copyright 2010

In case of sloping grade where the edges of the building footprint (AMBF) running perpendicular to the RROW has a difference in elevation of less than 3.00 meters, the highest adjoining natural grade (ground surface) or finished grade (sidewalk surface) shall be considered the

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

96

established grade elevation (Figure VII.1.); -

In case of sloping grade where the edges of the building footprint (AMBF) running perpendicular to the RROW has a difference in elevation of more than 3.00 meters, the average grade level of the building footprint (AMBF) shall be considered the established grade elevation (see Figure VII.3.); and

-

The building/structure height shall be measured from the highest adjoining public sidewalk (finished grade) or ground surface (natural grade); Provided, that the height measured from the lowest adjoining surface shall not exceed such maximum height by more than 3.00 meters; Except, that towers, spires and steeples, erected as parts of the building and not used for habitation or storage are limited as to the height only by structural design, if completely of incombustible materials, or may extend but not exceed 6.00 meters above the prescribed building height limit (BHL) for each occupancy group, if of combustible materials (Figures VII.2.). cSTHaE

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

97

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

98

3.

Other Considerations in Height Determination a.

In any given locality, the height of proposed buildings/structures shall be governed by the following factors: i. The designer/space planner must consider both the present and projected population density within the project site and in the project's location/area at full completion/operation of the project;

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

99

ii. For a given volume of building/structure (the building bulk), that which has a lesser Percentage of Site Occupancy (PSO) or area of ground coverage Allowable Maximum Building Footprint (AMBF) or Maximum Allowable Construction Area (MACA) may be built higher than that with a greater PSO, AMBF or MACA; iii. A proposed building/structure which has a greater TGFA requirement shall be built higher than that with a lower TGFA requirement; iv. A proposed building/structure on a lot with a higher FLAR designation/rights may be built higher than that on a lot with a lower FLAR designation/rights; and v. Lots that face a wider RROW and therefore with more RROW features/elements may become the site of a taller building/structure as compared to a lot facing a narrow RROW. DHATcE

b.

The height of proposed buildings/structures shall also be governed by the following RROW-based limitations: i. If only one (1) RROW services a lot and such is only 6.00 to 7.00 meters wide, a BHL of three (3) storeys (or 9.00 meters maximum) shall be observed regardless of use or occupancy, lot size, lot dimensions, lot frontage and like considerations. ii. If only one (1) RROW services a lot and such is only 4.00 to 5.00 meters wide, a BHL equivalent to 2 1/2 storeys (or 7.50 meters maximum) shall be observed regardless of use or occupancy, lot size, lot dimensions, lot frontage and like considerations. If only one (1) RROW services a lot and such is only 3.00 meters wide or less, a BHL equivalent to two (2) storeys (or 6.00 meters maximum) shall be observed regardless of use or occupancy, lot size, lot dimensions, lot frontage and like considerations. iii. Taller buildings are allowed for duly approved high-density developments such as Planned Unit Development (PUD) areas. Taller and bulkier buildings

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

100

are better suited in such areas due to higher end-user targets, more advanced and coordinated planning efforts and the application of more stringent development controls (DC) by the project proponents themselves. c.

The following factors shall also be considered in the determination of the building height: i. Soil characteristics, lot location in relation to fault lines and earthquake belts or proximity to volcanoes and other geological conditions. ii. Hydrological conditions such as the water table at the site and distance to waterways and shorelines. iii. Meteorological conditions such as the frequency and intensity of destructive typhoons/monsoon winds/rains, prevailing wind speed and direction, relative humidity, amount of precipitation and the prevailing ambient conditions. iv. Effect/s of environmental conditions on the building/structure and vice versa coupled with the effective control of air, noise and thermal pollution, radiant heat, lights and shadows, etc., and the optimization of natural light and ventilation. DEIHAa

v. Effect/s of traffic conditions on the building/structure and vice versa and the satisfaction of parking/loading requirements in accordance with this Rule. vi. Availability and capacity of public utility/service system considering the availability and adequacy of electric power, potable and non-potable water supply, drainage and sewerage, transportation and communications facilities, solid waste management system, etc. vii. Need for applicable building safety and maintenance systems, e.g., lightning arresters, beacons, protective railings and barriers, gondolas, window washing systems, etc. Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

101

d.

In accordance with the Standards and Recommended Practices (SARP) of the International Civil Aviation Organization (ICAO) where the Philippines is a member state and of Administrative Order No. 5 (Civil Air Regulation) of the Air Transportation Office (ATO), the following rules and regulations shall govern the construction of buildings/structures within the 24.00 kilometer radius of aerodromes where turbo-jet aircraft operate and within the 10.00 kilometer radius of aerodromes where no turbo-jet aircraft operate. (Figs. VII.4. through VII.8.) i. The height of buildings/structures within this area shall be limited by an imaginary line with slope of 2% or 1:50 for aerodromes where turbo-jet aircraft operate and 2.5% or 1:40 for aerodromes where no turbo-jet aircraft operate from the inner edge reckoned from the surface of the runway. The dimensions of the isosceles trapezoidal are as shown on Table VII.3. hereafter. Table VII.3. Dimensions of Isosceles Trapezoid

Type of Aerodrome

Inner Edge (Start Base)

Long Base (meters)

(meters)

Distance Between Bases (meters)

Aerodromes where turbo-jet aircraft

300

4,800

15,000

operates

150

4,650

15,000

Aerodromes where no turbo-jet aircraft

150

2,150

10,000

operates

100

2,100

10,000

ii. No new buildings/structures shall be allowed within the runway strip. iii. A height clearance certificate shall be first secured from the Air Transportation Office (ATO) before a building permit may be issued for the construction of buildings/structures located: (a) Within 4.00 kilometer radius of the runway ends of an aerodrome regardless of height; (b) From 4.00 kilometer to 24.00 kilometer Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

102

radius of the runway ends of an aerodrome where turbo-jet aircraft operate and exceeding 45.00 meters in height above the elevation of the runway; and ITESAc

(c) From 4.00 kilometer to 10.00 kilometer radius of the runway ends of an aerodrome where no turbo-jet aircraft operate and exceeding 45.00 meters in height above the elevation of the runway. AHcDEI

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

103

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

104

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

105

4.

Parking Slot, Parking Area and Loading/Unloading Space Requirements a.

The parking slot, parking area and loading/unloading space requirements listed hereafter are generally the minimum off-street cum on-site requirements for specific uses/occupancies for buildings/structures, i.e., all to be located outside of the road right-of-way (RROW).

b.

The size of an average automobile (car) parking slot must be computed at 2.50 meters by 5.00 meters for perpendicular or diagonal parking and at 2.15 meters by 6.00 meters for parallel parking. A standard truck or bus parking/loading slot must be computed at a minimum of 3.60 meters by 12.00 meters. An articulated truck slot must be computed at a minimum of 3.60 meters by 18.00 meters which should be sufficient to accommodate a 12.00 meters container van or bulk carrier and a long/hooded prime mover. A jeepney or shuttle parking/loading/unloading slot must be computed at a minimum of 3.00 meters by 9.00 meters. The parking slots shall be drawn to scale and the total number of which shall be indicated on the plans and specified whether or not parking accommodations are attendant-managed.

c.

The parking space ratings listed below are minimum off-street/off-RROW cum on-site requirements for specific uses/occupancies for buildings/structures, i.e., all to be located outside of the road right-of-way (RROW):

Table VII.4. Minimum Required Off-Street (Off-RROW) cum On-Site Parking Slot, Parking Area and Loading/Unloading Space Requirements by Allowed Use or Occupancy Specific Uses or of Occupancy (refer to Section 701 of this Rule)

Reference Uses or Character of Occupancies or Type of Buildings/Structures

Minimum Required Parking Slot, Parking Area and Loading Space Requirements

1.

GROUP A 1.1

Copyright 2010

Division A-1

CD Technologies Asia, Inc.

Single family and multi-family dwelling units [whether singledetached (R-1), single-attached or Philippine Laws Premium Edition 2009

Units with a lot measuring 32.00 to 72.00 sq. meters and/or with a dwelling unit having a gross 106

duplex (R-2) or rowhouse (R-3)], each privately owned or lots with dwelling units located in residential subdivisions/developments regardless of number of

floor area of from 18.00 to 22.00 sq. meters - a minimum of one (1) pooled off-street cum on-site parking slot* for every six (6) lots or lots with dwelling units;

hectares/dwelling units Units with a lot measuring 50.00 to 96.00 sq. meters and/or with a dwelling unit having a gross floor area of from 30.00 to 42.00 sq. meters - a minimum of one (1) pooled off-street cum on-site parking slot* for every four (4) lots or lots with dwelling units; Unit with a lot measuring 100.00 to 120.00 sq. meters and/or with a dwelling unit having a minimum gross floor area of from 30.00 to 42.00 sq. meters - a minimum of one (1) off-street cum on-site parking slot* for each lot or lot with dwelling unit; Unit with a lot measuring more than 120.00 sq. meters and/or with a dwelling unit having a minimum gross floor area of more than 42.00 s q. meters minimum of one (1) off-street cum on-site parking slot* for each lot or lot with dwelling unit; Units located In town house (R-4) buildings/structures regardless of number of storeys

Units with a gross floor area of 50.00 sq. meters - provide one (1) pooled parking slot* for every two (2) units or fraction thereof, i.e., with more than two (2) but not less than four (4) units; Unit with a gross floor area above 50.00 up to 150.00 sq. meters - provide one (1) parking slot* for each unit; Unit with a gross floor area above 150.00 sq. meters provide two (2) parking slots* for each unit.

Indigenous family dwelling units; each privately owned

At least one (1) car parking slot* for every six (6) dwelling units and which shall be provided outside of the RROW (within property or lot lines only)

1.2

Copyright 2010

Division A-2

CD Technologies Asia, Inc.

Multi-family dwelling units located in residential condominium (R-5) buildings/structures regardless of number of storeys

Philippine Laws Premium Edition 2009

Units with a gross floor area of from 18.00 to 22.00 sq. meters provide one (1) pooled parking slot* for every eight (8) units or for a fraction thereof, e.g., another slot* shall be provided 107

if there are more than eight, (8) units but less than sixteen 16 units, etc.; Units with a gross floor area up to 50.00 sq. meters - provide one (1) pooled parking slot* for every six (6) medium cost units or for a fraction thereof, e.g., another slot* shall be provided if there are more than six (6) but less than twelve (12) medium cost units, etc., or provide one (1) parking slot* for each open market unit (as defined under the revised IRR of PD 957); Units with a gross floor area above 50.00 sq. meters up to 100.00 sq. meters - provide one (1) pooled parking slot* for every four (4) medium cost units, or provide one (1) parking slot* for each open market unit (as defined under the revised IRR of PD 957); and Units with a gross floor area of more than 100.00 sq. meters one (1) parking slot* for each unit. 2.

GROUP B 2.1

Division B-1

Hotels

One (1) car parking slot for every three (3) rooms or a fraction thereof for highly urbanized areas and one (1) car parking slot for every seven (7) rooms or a fraction thereof for all other areas; and two (2) tourist bus parking slots for each hotel; provide at least one (1) loading slot for articulated truck or vehicle A 12.00 meters long container van plus 4.00 meter length for the prime mover and one (1) loading slot for a standard truck for every 5,000.00 sq. meters of gross floor area (GFA); and provide truck maneuvering area outside of the RROW (within property or lot lines only)

Residential hotels and apartels

One (1) car slot for every five (5) units or a fraction thereof; and one (1) bus parking slot for every sixty (60) rooms/units or a fraction thereof

Motels Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

One (1) car slot for every unit 108

Pension/boarding/lodging houses

One (1) car slot for every twenty (20) beds

3.

GROUP C 3.1

Division C-1

Bowling alleys

One (1) car slot for every four (4) alleys

3.2

Division C-2

Churches and similar places of worship

One (1) car slot and one (1) jeepney/shuttle slot for every 50.00 sq. meters of congregation area

Public elementary, secondary, vocational and trade school (GI)

One (1) off-street cum on-site parking slot for every ten (10) classrooms; and one (1) off RROW (or off-street) passenger loading space that can accommodate two (2) queued jeepney/shuttle slots

Private elementary, secondary, vocational and trade school (GI)

One (1) car slot for every five (5) classrooms; one (1) off-RROW (or off-street) passenger loading space that can accommodate two (2) queued jeepney/shuttle slots; and one (1) school bus slot for every one hundred (100) students

Public colleges and universities (GI)

One (1) car slot for every five (5) classrooms; one (1) off-RROW (or off-street) passenger loading space that can accommodate two (2) queued jeepney/shuttle slots; and one (1) school bus slot for every two hundred (200) students

Private colleges and universities (GI)

One (1) car slot for every three (3) classrooms; one (1) off-RROW (or off-street) passenger loading space that can accommodate two (2) queued jeepney/shuttle slots; and one (1) school bus slot for every one hundred (100) students

4.

GROUP D 4.1.

Division D-1

Mental hospitals, sanitaria and mental asylums and like uses

One (1) off-street cum on-site care parking slot for every twenty five (25) beds; and one (1) off-RROW (or off-street) passenger loading space that can accommodate two (2) queued jeepney/shuttle slots

4.2.

Copyright 2010

Division D-2

CD Technologies Asia, Inc.

Public hospital

Philippine Laws Premium Edition 2009

One (1) off-street cum on-site car parking slot for every twenty five (25) beds; and one (1) off-RROW (or off-street) passenger loading 109

space that can accommodate two (2) queued jeepney/shuttle slots; provide at least one (1) loading slot for articulated truck or vehicle (a 12.00 meter long container van plus 6.00 meter length for a long/hooded prime mover) and one (1) loading slot for a standard truck for every 5,000.00 sq. meters of gross floor area (GFA); and provide truck maneuvering area outside of the RROW (within property or lot lines only) Private hospital

One (1) off-street cum on-site car parking slot for every twelve (12) beds; and one (1) off-RROW (or off-street) passenger loading space that can accommodate two (2) queued jeepney/shuttle slots; provide at least one (1) loading slot for articulated truck or vehicle (a 12.00 meters long container van plus 6.00 meters length for a long/hooded prime mover) and one (1) loading slot for a standard truck for every 5,000.00 sq. meters of GFA; and provide truck maneuvering area outside of the RROW (within property or lot lines only)

4.3

Division D-3

Nursing homes for ambulatory patients, school and home, for children over kindergarten age, orphanages and the like

One (1) off-street cum on-site car parking slot for every twelve (12) beds; and one (1) off-BROW (or off-street) passenger loading space that can accommodate two (2) queued jeepney/shuttle slots

5.

GROUP E 5.1

Division E-1

Terminals, inter-modals or Multi-models, Depots and the like (UTS)

One (1) car slot for every 500.00 sq. meters of gross floor area or for a fraction thereof; and one (1) off-RROW (or off-street) passenger loading space that can accommodate two (2) queued jeepney/shuttle slots or two (2) queued bus slots whichever is applicable; maneuvering area of buses, trucks and like vehicles shall be outside of the RROW (within property or lot lines only)

Transit Stations and the like (UTS)

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

Provide on each side of the RROW one (1) off-RROW (or off-street) passenger loading space that can accommodate four (4) queued jeepney/shuttle slots or three (3) queued bus slots whichever is applicable; in case of elevated mass transit stations, on-roadway terminals or on-RROW terminals on both sides of the RROW may

110

be considered One (1) car slot for every 100.00 sq. meters of shopping floor area 5.2 Division E-2 jeepney/shuttle

Neighborhood shopping

One (1) customer (buyer)

center/supermarket (C-1)

parking slot for every 150.00 sq. meters of wet and dry market floor area and one (1) vendor (seller) jeepney/shuttle parking slot or loading space for every 300.00 sq. meters of wet and dry market floor area; and one (1) off-RROW (off-street) terminal that can accommodate at least two (2) jeepneys and six (6) tricycles for every 1,000.00 sq. meters of wet and dry market floor area

Public Markets (C)

One (1) car slot for every 30.00 sq. meters of customer area

Restaurants, fast-food centers, bars and beerhouses (C)

One (1) car slot for every 20 sq. meters of customer area: and two (2) tourist parking slots for tourist bus parking slots for each theater-restaurant

Nightclubs, super clubs and

One (1) car slot for every 30.00 sq.

theater-restaurants (C)

meters of customer area

Nightclubs, super clubs and theater-restaurants (C)

Units with a gross floor area of from 18.00 to 40.00 sq. meters - provide one (1) pooled parking slot* for every two (2) units or for a fraction

Units located in office, commercial or mixed-use condominium buildings/structures

Unit with a gross floor area of from 41.00 to 70.00 sq. meters - provide one (1) parking slot* for each unit;

thereof;

regardless of and number of storeys Unit with a gross floor area of more than 70.00 sq. meters provide one (1) parking slot* for every 70.00 sq. meters and for a fraction thereof; Columbarium

One (1) car slot for every compartment

Aircraft hangars, open parking carports and garages etc.

One (1) car slot for every 1,000.00 sq. meters of gross floor area and one (1) bus slot for every one hundred (100) workers; if number of workers exceed two hundred (200), provide one (1) off-RROW (or off-street) passenger loading space that can accommodate two

niche 5.3

Division E3

(2) queued jeepney/shuttle slots

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

111

6.

GROUP F 6.1.

Division F-1

Industrial buildings, mills, breweries, etc. (I)

One (1) car slot for every 1,000.00 sq. meters of gross floor area and one (1) bus slot for every one hundred (100) workers; if number of workers exceed two hundred (200), provide one (1) off-RROW (or off-street) passenger loading space that can accommodate two (2) queued jeepney/shuttle slots; provide at least one (1) loading slot for truck or vehicle (a 12.00 meter long container van plus 6.00 meters length for a long/hooded prime mover) and one (1) loading slot for a standard truck for every 5,000.00 sq. meters of GFA; and provide truck maneuvering area outside of the RROW (within property or lot lines only)

7.

GROUP G 7.1

Division G-1

Industrial buildings, factories, manufacturing establishments, mercantile buildings, warehouses, storage bins, power and water generation/distribution facilities

One (1) car slot for every 1,000.00 sq. meters of gross floor area and one (1) bus slot for every one hundred (100) workers; if number of workers exceed two hundred (200), provide one (1) off-RROW (or off-street) passenger loading space that can accommodate two (2) queued jeepney/shuttle slots; provide at least one (1) loading slot for articulated truck or vehicle (a 12.00 meter long container van plus 6.00 meters length for a

long/hooded prime mover) and one (1) loading slot for a standard truck for every 5,000.00 sq. meters of GFA; and provide truck maneuvering area outside of the RROW (within property or lot lines only)

8.

7.2.

Division G-2

-do-

-do

7.3.

Division G-3

- do-

-do

7.4.

Division G-4

-do-

-do

7.5.

Division G-5

- do -

-do

Public recreational assembly buildings such as theaters/cinemas, auditoria, etc.

One (1) car slot and one (1) jeepney/shuttle slot for every 50.00 sq. meters of spectator area; and one (1) bus parking slot for every two hundred (200)

GROUP H 8.1

Copyright 2010

Division H-1

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

112

spectators 8.2

Division H-2

Dance halls, cabarets, ballrooms, skating rinks and

-do

cockfighting arenas, etc. 8.3

8.4

Division H-3

Division H-4

Dance halls, ballrooms, skating rinks, etc.

do

Covered amusement parks, amusement and entertainment complexes,

one (1) car slot for every 50.00 sq. meters of gross floor area

etc.

9.

Clubhouses, beach houses

one (1) slot for every 100.00

and the like

sq. meters of gross floor area

Recreational or similar public assembly buildings such as stadia, sports complexes, convention centers, etc.

One (1) car slot and one (1) jeepney/shuttle slot for every 50.00 sq. meters of spectator area; and one (1) bus parking slot for every two hundred (200)

GROUP I 9.1.

Division I-1

spectators. 10. GROUP J

Agriculture-related uses or occupancies (A)

10.1

Division J-1

Not required if located outside urbanized area; if located within urbanized area, provide one (1) car slot for every 1,000.00 sq. meters of gross floor area and one (1) bus slot for every one hundred (100) workers; if number of workers exceed two hundred (200), provide one (1) off-RROW (or off-street) passenger loading space that can accommodate two (2) queued jeepney/shuttle slots; provide at least one (1) loading slot for articulated truck or vehicle (a 12.00 meter long container van plus 6.00 meters length for a long/hooded prime mover) and one (1) loading slot for a standard truck for every 5,000.00 sq. meters of GFA; and provide truck maneuvering area outside of the RROW (within property or lot lines only)

10.2. Division J-2

Other uses not classified in previous sections

Provide parking requirements stipulated for most similar or

(PUD, etc.)

most related uses/occupancies

Note:

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

113

* The parking slot requirements shall be an integral part of buildings/structures and any parking slot provided outside the building/structure will be quantified only as buffer parking. ** The following prohibitions on parking slots: 1. Conversion/change of use/occupancy. 2. Reduction of parking spaces. 3. Encroachment on RROW. 4. Public utility and bulky vehicles.

d.

In computing for parking slots, a fraction of 50% and above shall be considered as one (1) car parking slot to be provided. In all cases however, a minimum of one (1) car parking slot shall be provided unless otherwise allowed under this Rule. i. Multi-floor parking garages may serve the 20% parking requirements of the building/structure within 200.00 meter radius, provided at least 80% of the parking requirements are complied with and integrated in the building design. ii. Special Provision on the Handicapped: For buildings/structures to be provided with features intended for the use or occupancy of the handicapped, the minimum provisions of Batas Pambansa (BP) Bilang 344 and its Implementing Rules and Regulations (IRR) with respect to parking shall be strictly observed.

e.

Allowed Off-RROW/Off-Street cum Off-Site Parking Provision: i. In addition to on-site cum off-RROW (off-street) parking provisions mandated under this Rule, off-site cum off-street parking facilities may be allowed and considered part of a project provided that such facilities specifically consist of reserved or leased parking slots within a permanent parking building/structure and not in a vacant parking lot or parking structure/space for a commercial development and provided further that such parking slots are located no more than 100.00 meters away from a residential building project or are located no more than 200.00 meters away from an office or commercial building project.

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

114

ii. Direct access of parking/loading/utility slots and terminals to the RROW shall be generally disallowed to prevent the usage of the BROW as a maneuvering area. iii. Traffic generating buildings such as shopping malls or similar facilities that have very high volumes of pedestrian and vehicular traffic may be located at major intersections or within 100.00 meters of such intersections, provided that the distance between the street curb of the ingress/egress of such a commercial lot/property (nearest the intersection) and the straight curb of the intersection shall not be less than 50.00 meters. (Fig. VII.9.)

iv. For R-2, R-3, GI, C, C-2 and C-3 uses or occupancies, front yards abutting RROW are not to be used for long-term off-street parking. Due to the very public nature of these uses (high vehicular and pedestrian concentrations), the front yard (a transition Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

115

space between the RROW and the building/structure) shall be used exclusively for driveways, off-RROW loading spaces, short-term off-RROW parking and landscaping (hardscape and softscape) treatment. Temporary or short-term off-street parking, particularly on driveways, shall preferably be only for visitors to these buildings/structures. v. For Basic R-2 and Basic R-3 uses or occupancies (for single family dwelling units only), up to 50% of the front yard abutting the RROW may be paved/hardscaped, i.e., converted into a courtyard for carport use. Such use shall not be permitted in all other uses or occupancies. SECTION 708. 1.

Minimum Requirements for Group A Dwellings. —

Dwelling Location and Lot Occupancy The dwelling shall occupy not more than 90% of a corner lot and 80% of an inside lot, and subject to the provisions on Easements of Light and View of the Civil Code of Philippines, shall be at least 2.00 meters from the property line.

2.

Light and Ventilation Every dwelling shall be so constructed and arranged as to provide adequate light and ventilation as provided under Section 805 to Section 811 of the Code.

3.

Sanitation Every dwelling shall be provided with at least one sanitary toilet and adequate washing and drainage facilities.

4.

Foundation Footings shall be of sufficient size and strength to support the load of the dwelling and shall be at least 250 millimeters thick and 600 millimeters below the surface of the ground.

5.

Post The dimensions of wooden posts shall be those found in Table VII.5.: Dimensions of Wooden Posts. Each post shall be anchored to such

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

116

footing by straps and bolts of adequate size. Table VII.5.: Dimensions of Wooden Posts or Suportales Maximum Type Building

Maximum Height of 1st Floor (meters)

MaximumRequired Maximum Height Spacing of Finished Size of Total Post Suportales (meters) (meters) (millimeters)

1-Storey Shed 1-Storey Shed 1-Storey Shed 1-Storey House or Chalet 1.00-3.00 2-Storey House 3.00 2-Storey House 4.50 2-Storey House 5.00 2-Storey House -

4.00 3.00 5.00

3.50 4.00 4.00

100 x 100 100 x 100 125 x 125

5.50 6.00 7.00 8.00 9.00

3.60 3.00 4.00 4.50 4.50

125 x 125 125 x 125 120 x 120 175 x175 200 x 200

Logs or tree trunk suportales may be used as post in indigenous traditional type of construction, provided that these are of such sizes and spacing as to sustain vertical loading equivalent at least to the loading capacities of the posts and spacing in this Table. TCIDSa

6.

Floor The live load of the first floor shall be at least 200 kilograms per sq. meter and for the second floor, at least 150 kilograms per sq. meter.

7.

Roof The wind load for roofs shall be at least 120 kilograms per sq. meter for vertical projection.

8.

Stairs Stairs shall be at least 750 millimeters in clear width, with a rise of 200 millimeters and a minimum run of 200 millimeters.

9.

Entrance and Exit There shall be at least one entrance and another one for exit.

10.

Electrical Requirements All electrical Installations shall conform to the requirements of the

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

117

Philippine Electrical Code. 11.

Mechanical Requirements Mechanical systems and/or equipment installations shall be subject to the requirements of the Philippine Mechanical Code.

SECTION 709.

Requirements for Other Group Occupancies. —

Subject to the provisions of the Code, the Secretary shall promulgate rules and regulations for each of the other Group Occupancies covering: allowable construction, height, and area; location on property, exit facilities, light and ventilation, sanitation; enclosures of vertical openings; fire extinguishing systems; and special hazards. Guidelines on Building Bulk, Development Controls, Buildings and Other Accessory Structures Within Cemeteries and Memorial Parks A.

Determining Building Bulk

1.

General. Building bulk (a volume quantity) shall be generally determined by the application of the Floor-Lot Area Ratio (FLAR), vertically projecting the Allowable Maximum Building Footprint (AMBF), establishing the Outermost Faces of Building (OFB) and quantifying the Allowable Maximum Volume of Building (AMVB). The building bulk may be ultimately governed by the width of the RROW and other applicable provisions for light and ventilation (including incremental setbacks as a result of satisfying natural light and ventilation requirements for RROW and front yards as partly shown in Table VII.G.1. hereafter).

2.

Application of the FLAR. The FLAR (Table VII.G.1.) shall be the primary or initial determinant of the building bulk.

Table VII.G.1. Reference Table of Floor to Lot Area Ratio (FLAR) Designations/Rights Type of Use or Occupancy Residential

Type of Building/Structure Residential 1 (R-1)

FLAR Designation/Rights 1.50 (at a 3-storey or 10.00 m BHL)

Residential 2 (R-2) Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

118

Residential 2 (R-2) a. Basic R-2

1.30 up to 1.50 (at a 3-storey or 10.00 m BHL)

b. Maximum R-2

2.10 up to 3.00 (at a 5-storey or 15.00 m BHL)

Residential 3 (R-3) a. Basic R-3

1.80 up to 2.10 (at a 3-storey or 10.00 m BHL)

b. Maximum R-3

7.10 up to 8.10 (at a 12-storey or 36.00 m BHL)

Individual Lot for Residential 4 1.60 up to 1.80 (R-4)/Townhouses (at a 3-storey or 10.00 m BHL) Residential 5(R-5)/ Condominiums Commercial

Industrial

6.00 up to 9.00 (at an 18-storey or 54.00 m BHL)

Commercial 1 (Com-1)

1.70 up to 3.00 (at a 5-storey or 15.00 m BHL)

Commercial 2 (Com-2)

3.60 up to 9.00 (at a 15-storey or 45.00 m BHL)

Commercial 3 (Com-3)

9.00 up to 34.00 (at a 60-storey or 180.00 m BHL)

Industrial 1 (Ind-1)

1.50 up to 2.50

Industrial 2 (Ind-2)

2.50 up to 3.00

Industrial 3 (Ind-3)

3.00 up to 5.00

Institutional

-

2.50

Cultural

-

3.50

Utility/Transportation/Road Rights-of Way (RROW)/ Services -

2.00 up to 3.00

Parks and Open Recreational Spaces -

0.50 up to 1.00

Agricultural/AgroIndustrial/Tourism

1.80 up to 2.20

-

Planned Unit PUD at a reclamation area close Development (PUD) to an operating airport PUD at a reclamation area Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

6.00 6.00 up to 12.00 119

PUD at a coastal area

12.00 up to 18.00

PUD at an inland area very close to an operating airport

6.00 up to 18.00

PUD at an inland area Cemetery

9.00 up to 34.00 (at a 60-storey or 180.00 m BHL)

-

0.80

Table VII.G.2. Conversion Table of Gross Floor Area (GFA) to Total Gross Floor Area (TGFA) Type of Building/Structure Excluded Floor Areas (nonbased on Use/Occupancy GFA) as a Percentage (%) of the TGFA Residential 1 33% Residential 2 (Basic), Residential 3 (Basic) 20% and Residential 4 Residential 2 (Maximum), Residential 3 (Maximum) and Residential 5 16% Commercial 1 20% Commercial 2 25% Commercial 3 33% Industrial 1 25% Industrial 2 and 3 33% Transportation, Utility and Service Areas 33% Agricultural and Agro-Industrial 2%-5%

3.

Multiplier to Convert the GFA to TGFA 1.50 1.25

1.20 1.25 1.33 1.50 1.33 1.50 1.50 1.03-1.06

Establishing the OFB. The OFB shall be primarily determined by the vertical projections of the outermost faces of the AMBF up to a height prescribed by the applicable BHL. Figure VII.G.1. shows the determination of the angular planes needed to establish the outer limits for walls and projections of the proposed building/structure facing RROW and for their corresponding roof configurations. Table VII.G.3. also shows the recommended angles or slopes for the angular planes originating from the centerline of the RROW for R-1 and C-3 properties only. Angles or slopes for other permitted uses/occupancies can be extrapolated from the two (2) examples. (Figs. VIII.G.1. and VIII.G.2.) CDHAcI

Table VII.G.3. Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

120

Reference Table of Angles/Slopes* To Satisfy Natural Light and Ventilation Requirements Along RROW and Front Yards

Type of Use or Occupancy

Width or Road Rightof-Way (RROW)

Angle or Slope of Angular

Angle or Slope of Angular

Plane for Buildings/Structures

Plane for Buildings/Structures

Without Projections**

With Projections*

Angle from Centerline of RROW

Ratio (Slope)

(Degrees) Residential 1

8.00 meters

46.5

Angle from Centerline of RROW (Degrees)

9m:8.5m

(R-1)

50.0

(1.06) 10.00 meters

43.0

9m:9.5m

40.0

9m:10.5m

46.0

38.0

9m:11.5m

43.0

35.0

9m:12.5m

39.0

33.5

9m:13.5m

36.0

31.0

9m:14.5m

33.0

8.00 meters

71.0

48m:16.5m

(C-3)

7.5m:11.25m (0.67)

32.0

(0.62) Commercial 3

7.5m:10.25m (0.73)

(0.67) 20.00 meters

7.5m:9.25m (0.81)

(0.72) 18.00 meters

7.5m:8.25m (0.91)

(0.78) 16.00 meters

7.5m:7.25m (1.03)

(0.86) 14.00 meters

7.5m:625m (1.20)(1.20)

(0.95) 12.00 meters

Ratio (Slope)

7.5m:12.25m (0.61)

-

-

-

-

-

-

-

-

-

-

-

-

-

-

(2.90) 10.00 meters

69.5

48m:17.5m (2.74)

12.00 meters

68.0

48m:18.5m (2.59)

14.00 meters

65.5

48m:19.5m (2.46)

16.00 meters

63.6

48m:20.5m (2.34)

18.00 meters

61.7

48m:21.5m (2.23)

20.00 meters

60.00

48m:22.5m (2.13)

NOTE: *

Copyright 2010

To be used for plotting the angular plane from the grade level centerline of the RROW. The angular plane can also help determine the Allowable Maximum Volume of Building (AMVB) as well as the alternative incremental setback lines. Only the uses/occupancies with the least and heaviest developments (R-1 and C-3 respectively are shown). The angles/slopes of angular planes for all CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

121

other uses/occupancies in between can be extrapolated. **

Considered projections from the outermost face of the building/structure are eaves, medias aguas (canopy for windows), cantilevers, heavy sign supports (only for applications permitted or consistent with the Code) and the like.

4.

B.

Quantifying the AMVB. The AMVB shall be primarily determined by the following: a.

Multiply the AMBF (in square meters) for the lot by the applicable BHL (in meters) for the lot to arrive at the initial AMVB (in cubic meters); the result of this step is the imaginary footprint prism;

b.

Superimpose the angular plane originating from the center of the RROW on the footprint prism; this shall result in the reduction of the initially computed building volume due to the application of incremental setbacks and of roof configuration dictated by the angular plane; the result of this step is the AMVB;

c.

To cross-check the AMVB against the Allowable Maximum TGFA (separately determined), convert the AMVB into its approximate area equivalent (in sq. meters) by dividing it with the BHL. Before converting the AMVB to its area component, check for the effects of the incremental setbacks on the TGFA for each floor of the proposed building/structure.

Application of Development Controls (DC) (To Determine the Maximum Development Potential of a Lot) 1. Sizing the Building/Structure. To determine the allowed/appropriate building bulk (volume), the following series of steps using the DC under this Guideline and other Rules in the Code shall be followed: a. Refer to Rule VIII for prescribed setbacks, yards, courts (at grade level), etc. applicable to the lot/project site; determine the extent of firewall construction if required and/or if permitted; refer to Rule VIII for the Percentage of Site Occupancy (PSO); compute for the Allowable Maximum Building Footprint (AMBF) under

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

122

this Rule by using the formula: Allowable Maximum Building/Footprint or AMBF (in sq. meters)

Total Lot Area (TLA)

=

-

Land area required for yards/courts

Additional buildable lot area due to Firewall construction (if permitted under this Rule)

+

(prescribed under Rule VIII)

b. Check resultant building footprint against applicable PSO under Reference Table VIII.1. of Rule VIII and consult existing/applicable and/or duly approved zoning ordinances; to check, use the formula: Percentage of Site Occupancy (PSO)

=

Allowable Maximum Building Footprint or AMBF (in square meters)

Total Lot Area (TLA)

÷

c. Compute for the resultant height of the building/structure by referring to Table VII.2. of this Rule and by using the formula: Resultant Height of the building/structure (in meters)

=

Building Height Limit or the BHL (as expressed in number of floors/storeys)

x

Desired Floor to Floor Height (in meters)

d. Check the resultant height against the BHL (refer to Table VII.2. of this Rule); if a greater building/structure height is desired, consult existing zoning ordinances or other applicable laws for possible relief; if relief cannot be sought, explore sub-grade (basement level) solutions or reduce the desired floor to floor heights in case it is greater than 3.00 meters; e. Establish the Outermost Faces of Building (OFB) to help determine the Allowable Maximum Volume of Building (AMVB) and to satisfy natural light and ventilation requirements for RROW and front yards abutting RROW; an imaginary prism within which the proposed building/structure must fit shall result, unless specifically allowed under the Code; thereafter, establish the Outermost Limits of Building Projections (OLBP) to fully comply with other applicable light and ventilation provisions; f. Initially determine building bulk by computing for the maximum allowable Gross Floor Area (GFA) for the Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

123

building/structure using the formula: Gross Floor Area (GFA) of the building/structure = (in square meters)

Total Lot Area (TLA)

x

Recommended Floor to Lot Area Ratio (FLAR)*

NOTE: *Refer to Table VII.G.1. of this Guideline (Recommended FLAR Designations/Rights) and/or consult existing/applicable and duly-approved zoning ordinances.

i. GROSS FLOOR AREA (GFA) — the total floor space within the perimeter of the permanent external building walls (inclusive of main and auxiliary buildings) such as office areas, residential areas, corridors, lobbies and mezzanine level/s. The GFA shall also include building projections which may serve as floors or platforms that are directly connected to/integrated with areas within the building/structure, e.g., balconies (Refer to Section 1004 of Rule X of this IRR) and the GFA excludes the following: cAaDCE

(a) Covered areas used for parking and driveways, services and utilities; (b) Vertical penetrations in parking floors where no residential or office units are present; and (c) Uncovered areas for helipads, air-conditioning cooling towers or air-conditioning condensing unit (ACCU) balconies, overhead water tanks, roof decks, laundry areas and cages, wading or swimming pools, whirlpools or jacuzzis, terraces, gardens, courts or plazas, balconies exceeding 10.00 sq. meters, fire escape structures and the like. g. Determine the Allowable Maximum Total Gross Floor Area (TGFA) to approximate building volume using the formula hereafter. In particular, determine the minimum required off-street cum on-site parking provisions, driveways and related access systems, particularly for new developments and/or re-developments whereby provisions of this Guideline Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

124

shall apply. Total Gross Floor Area (TGFA) of the building/structure = (in sq. meters)

Gross Floor Area (GFA) of the building/structure (in square meters)

+

Non-GFA areas*

-

All requirements for courts at all floors (above grade) under Rule VIII (in square meters)

NOTE: "Compute for all other areas not covered by the FLAR or by the GFA using Table VII.G.2.

i. TOTAL GROSS FLOOR AREA (TGFA) — the total floor space within the main and auxiliary buildings primarily consisting of the GFA and all other enclosed support areas together with all other usable horizontal areas/surfaces above and below established grade level that are all physically attached to the building/s which shall consists of the following: (a) Covered areas used for parking and driveways, services and utilities. The TGFA specifically excludes provisions for courts above grade level; (b) Vertical penetrations in parking floors where no residential or office units are present; (c) Uncovered areas for helipads, air-conditioning cooling towers or ACCU balconies, overhead water tanks, roof decks, laundry areas and cages, wading or swimming pools, whirlpool or jacuzzis, terraces, gardens, courts or plazas, balconies exceeding 10.00 sq. meters, fire escape structures and the like; and (d) Other building projections which may additionally function as floors or platforms if properly reinforced, e.g., the top surfaces of roof extensions/eaves, sun-breakers, large roofed or cantilevered areas such as porte cocheres, canopies and the like. Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

125

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

126

Establishing the Outmost Faces of Building (OFB) for a Typical R-1 Use/Occupancy Through the Use of the AMBF, The BHL, the AMVB and The Angular Plane Along the RROW (14.00 M Wide RROW) C. Buildings and Other Accessory Structures Within Cemeteries and Memorial Parks 1.

Location of Cemeteries/Memorial Parks a.

2.

3.

Copyright 2010

Cemeteries and Memorial Parks shall be located in accordance with the approved land use plan of the city/municipality concerned. Prior clearance shall be obtained from the Department of Health, the National Water Resources Council, the Department of Environment and Natural Resources and the Housing and Land Use Regulatory Board.

Protective Enclosures a.

The cemetery shall be totally enclosed by a perimeter fence/wall of strong material, and all gates shall be provided with a strong door and lock. Perimeter wall shall not exceed 3.00 meters in height.

b.

Where a cemetery is enclosed by a solid reinforced concrete wall at least 2.00 meters high, it is allowed to construct tombs, vaults, mausoleums or other types of sepulchres for the dead up to the walls. Otherwise, a clearance of 5.00 meters shall be maintained between the perimeter fence and the nearest interment plot.

Interments, Burials and Entombments a.

For ground interments, there shall be a minimum depth of excavation of 1.50 meters from ground level to base of excavation. However, if concrete vaults are used, the minimum depth of excavation from base of vault to ground level shall be 1.00 meter, depending on the depth of ground water table.

b.

Ground interments shall be allowed only in designated

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

127

graveyard areas of the cemetery and may be provided with suitable markers, headstones or memorials. c.

Vaults for tombs and mausoleums for aboveground interments shall be of solid reinforced concrete. Concrete hollow blocks or any unit masonry construction of ceramics, adobe or the like shall not be allowed for the construction of above-ground vaults; tombs or mausoleums. Mausoleums may be provided with ossuaries and/or cineraria along the interior walls.

d.

Multi-level interment niches shall only be of solid reinforced concrete construction, of not less than 150 millimeters thickness in which case they may be allowed to abut walls of the cemetery, provided, the walls are of solid reinforced concrete construction. Concrete hollow blocks, or any unit masonry construction of ceramics, adobe or the like shall not be allowed.

e.

Before construction is started on any mausoleum, canopy over a tomb, or multi-level niches, a building permit shall be secured therefor from the OBO.

f.

Horizontal divisions of columbaria shall be of reinforced concrete of at least 50 millimeters thickness. Vertical divisions may be of concrete hollow blocks of at least 100 millimeters thickness, in which case, cement mortar shall be applied evenly to present a non-porous surface. Minimum dimensions of individual cinerarium shall be 300 millimeters by 300 millimeters by 460 millimeters. Cinerary remains shall be placed inside tightly sealed urns. CTAIDE

4.

Copyright 2010

Accessory Structures a.

A chapel with a floor area of at least 50.00 sq. meters shall be constructed at a convenient location within the cemetery where funeral ceremonies may be held, and incidentally serve as haven for funeral participants against sun and rain.

b.

Wake chaplets with a minimum area of 50.00 sq. meters for thirty (30) persons and at least 1.60 sq. meters for

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

128

each additional person may be provided. c.

Administrative Office — a 64.00 sq. meters lot shall be allocated for an administration building office for memorial parks with an area of above one (1) hectare.

d.

Electrical Power Supply — Distances of lampposts for street lighting shall be placed at a maximum of 100.00 meters or as prescribed by the power firm servicing the area. Utility poles shall be installed along sides of streets and pathways.

e.

Parking Area — Parking area equivalent to a minimum of five 5% of the gross area of memorial park/cemetery shall be provided over and above the required parking area/facility for any structures to be constructed within the premises of the memorial park/cemetery.

f.

Comfort Rooms — Adequate and clean comfort rooms with facilities for disabled persons shall be provided in properly located areas.

NOTE: Refer also to the latest applicable HLURB Guidelines regarding Cemeteries and Memorial Parks. RULE VIII Light And Ventilation SECTION 801.

Copyright 2010

General Requirements of Light and Ventilation. —

1.

Subject to the provisions of the Civil Code of the Philippines on Easements of Light and View, and to the specific provisions of the Code, every building shall be designed, constructed, and equipped to provide adequate light and ventilation. (Refer to Guidelines on Easements, View Corridors/Sight Lines and Basements at the end of this Rule)

2.

All buildings shall face a street or public alley or a private street which has been duly approved. (Refer to Guidelines on Streets/RROW and Sidewalks at the end of this Rule)

3.

No building shall be altered nor arranged so as to reduce the size of any room or the relative area of windows to less than

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

129

that provided for buildings under this Rule, or to create an additional room, unless such additional room conforms to the requirements of this Rule. 4.

No building shall be enlarged so that the dimensions of the required court or yard would be less than what is prescribed for such building lot.

SECTION 802. 1.

The measurement of site occupancy or lot occupancy shall be taken at the ground level and shall be exclusive of courts, yards, and light wells.

2.

Courts, yards, and light wells shall be measured clear of all projections from the walls enclosing such wells or yards with the exception of roof leaders, wall copings, sills, or steel fire escapes not exceeding 1.20 meters in width.

SECTION 803.

Copyright 2010

Measurement of Site Occupancy. —

Percentage of Site Occupancy. —

1.

The measurement of the percentage (%) of site occupancy (or lot occupancy) shall be taken at the ground level and shall be exclusive of courts, yards and light wells. Courts, yards, and light wells shall be measured clear of all projections from the walls enclosing such wells or yards with the exception of roof leaders, wall copings, sills, or steel fire escapes not exceeding 1.20 meters in width.

2.

In case of proposed additional construction on a lot on which another building/structure already stands, the Percentage of Site Occupancy (PSO) arising out of such existing buildings/structures must be included in the computation of the PSO for the Total Lot Area (TLA). In case of discrepancy between the specified Maximum Allowable PSO and the other light and ventilation provisions under this Rule, the resulting lesser building/structure footprint or gross floor area at the ground floor (or at grade level) must prevail.

3.

Maximum site occupancy shall be governed by use, type of construction, and height of the building and the use, area, nature and location of the site; and subject to the provisions of the local zoning requirements and in accordance with the following

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

130

types of open spaces: a.

Public open spaces — streets, alleys, easements of sea/lakeshores, rivers, creeks, esteros, railroad tracks, parks/plazas, playgrounds, and the like.

b.

Total Open Spaces within Lot (TOSL) — courts, yards, gardens, light wells, uncovered driveways, access roads and parking spaces consisting of two (2) types: i. Paved or tiled (hardscaped areas); sub-classification of open space shall fall under Maximum Allowable Impervious Surface Areas (ISA) within the Total Lot Area (TLA); and ii. Unpaved areas within the lot that are with exposed soil and planted (softscaped), i.e., the Unpaved Surface Areas (USA); this sub-classification is the true open space.

4.

The following Table illustrates the manner in determining the Maximum Allowable Percentage of Site Occupancy (PSO), Maximum Allowable Impervious Surface Area (ISA), Maximum Allowable Construction Area (MACA), Minimum Unpaved Surface Area (USA), and the Total Open Space within Lot (TOSL) with reference to Type of Land Use Zoning per Lot.

Table VIII.1. Reference Table of Maximum Allowable PSO, Maximum Allowable ISA, the MACA, the Minimum USA and the TOSL by Type of Land Use Zoning per Lot % of Total Lot Area (TLA) Building/Structure Duly-Approved Maximum Use or Occupancy Zoningb Allowable (or Land Use)a PSOGcd

Residential

Copyright 2010

Basic Residential 2 (R-2)/Medium Density Housing [single family dwelling unit with a Building

CD Technologies Asia, Inc.

Maximum Allowable ISAc (Paved Open Spaces)

Minimum USA (Unpaved Open Spaces)

TOSLd (ISA+ USA

55e

30

15

45

60f

30%

10

40

Philippine Laws Premium Edition 2009

131

Height Limit (BHL) of 10.00 meters] Maximum R-2/ Medium Density Housing (multiple family dwelling units within one building/structure with a BHL of 15.00 meters) Basic Residential 3 (R-3)/High Density Housing (single family dwelling unit with a BHL

60e

30

10

40

70f

20

10

30

65e

20

15

35

70f

20

10

30

70e

20

10

30

80f

10

10

20

70e

20

10

30

80f

10

10

20

70e

20

10

30

80f 70e

10 20

10 10

20 30

(Com-1)

80f

10

10

20

Commercial 2

75e

20

5

25

(Com-2)

85f

10

5

15

Commercial 3

80e

15

5

20

(Com-3)

90f

5

5

10

Industrial 1

70e

2

10

30

(Ind-1)

80f

10

10

20

Industrial 2

70e

5

15

30

(Ind-2)

80f

5

15

20

Industrial 3

70e

15

15

30

(Ind-3)

80f

5

15

20

of 10.00 meters) Maximum R3/ High Density Housing (multiple family dwelling units within one building/structure with a BHL of 36.00 meters) Residential 4 (R-4)/Individual Townhouse Units Residential 5 (R-5)/ Condominiums Commercial Commercial 1

Industrial

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

132

Institutional

-

Cultural

50e

20

30

50

60f

20

20

40

60e

20

20

40

70f

20

10

30

50e

40

10

50

60f

30

10

40

-

22.72 (of total width of RROW as Paved portion of sidewalk)

PUD at a reclamation area close to an operating airport

20

30

50

80

70

15

15

30

PUD at a reclamation area

70

15

15

30

PUD at a

70

15

15

30

coastal area PUD at an Inland area close to an

70

10

20

30

operating airport PUD at inland area

70

10

20

30

-

85

10

5

15

-

Utility/

-

Transportation/ Services Sidewalks/ Arcades at RROW

-

Parks and Open Recreational Spaces Planned Unit Development (PUD)

Cemetery

11.11 33.33 (of total width (of total width of RROW as of RROW) Unpaved portion of sidewalk)

Notes: a)

per duly-approved City/Municipal Comprehensive Land Use Plan (CLUP)

b)

per duly-approved City/Municipal Zoning Ordinance (ZO) and its IRR

c)

PSO + ISA = MACA (Maximum Allowable Construction Area)

d)

PSO + TOSL = TLA (Total Lot Area).

e)

without firewall

f)

with firewall

4.

Minimum Requirements for Total Open Spaces within Lot (TOSL) a.

Copyright 2010

Total Open Spaces within Lot (TOSL) are portions of the Total Lot Area (TLA) not occupied by the Maximum

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

133

Allowable PSO. The TOSL may consist of either the Maximum Allowable ISA (hardscaped areas) or the USA (exposed and planted/softscaped soil) or may also be the combination of both types of open spaces. (Figure VIII.1.) b.

Group A buildings or Residential 1 (R-1) uses/occupancies shall follow the minimum yard standards in Table VIII.2. to comply with the TOSL requirement. EDHTAI

c.

Abutments for Basic Uses/Occupancies forming part of new developments shall be basically similar to the restrictions prescribed for firewalls under Rule VII, to wit: i. Absolutely no abutments are allowed at any property line for any R-1 lot type/location. ii. Abutments shall be allowed on only one (1) side for any R-2 lot type/location. There shall be no firewalls/abutments on the front and rear property lines for any R-2 lot type/location. iii. Abutments shall be allowed on two (2) sides only or on one (1) side and the rear property line/boundary for any R-3 lot type/location. There shall be no abutments on the front property line for any R-3 lot type/location. iv. Abutments shall be allowed on two (2) sides only for any R-4 lot type/location. There shall be no firewalls/abutments on the front and rear property line for any R-4 lot type/location. v. Abutments shall be allowed on two (2) sides only or on one (1) side and the rear property line/boundary for any R-5 lot type/location. There shall be no abutments on the front property line for any R-5 lot type/location. vi. Abutments shall be allowed on two (2) sides only or on one (1) side and the rear property line/boundary for any C-3 lot type/location. There shall be no abutments on the front property line for any C-3 lot type/location.

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

134

d.

Lot Type/Location Only seven (7) types of lots and their respective locations are described under this Rule. (Figures VIII.2. through VIII.8.)

e.

Variance When the lots as described In Figures VIII.2. through VIII.8. are too narrow or too shallow such that the public open space, e.g., RROW, alley or the like on which they abut can adequately supply light and ventilation to every room therein subject to the requirements on window opening, the requirements on the minimum Total Open Space within Lot (TOSL) above may be waived (Figures VIII.9. through VIII.11.), provided however, that for lots abutting on only one (1) public open space, the depth of the open space to be provided shall not be more than 8.00 meters; and for those lots abutting two (2) or more public open spaces, the depth of the open space to be provided shall not be more than 12.00 meters.

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

135

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

136

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

137

Lot Types SECTION 804.

Sizes and Dimensions of Courts. —

1.

Minimum sizes of courts and yards and their least dimensions shall be governed by the use, type of construction, and height of the building as provided hereunder, provided that the minimum horizontal dimension of said courts and yards shall be not less than 2.00 meters. All inner courts shall be connected to a street or yard, either by a passageway with a minimum width of 1.20 meters or by a door through a room or rooms.

2.

The required open space shall be located totally or distributed anywhere within the lot in such a manner as to provide maximum light and ventilation into the building. (Figures VIII.12. through VIII.15.)

3.

YARD — the required open space left between the outermost face of the building/structure and the property lines, e.g., front, rear, right and left side yards. The width of the yard is the setback. Yards prescribed for Commercial, Industrial, Institutional and Recreational Buildings are shown in Table VIII.3. hereafter. Table VIII.2. Minimum Setbacks for Residential Buildings/Structures Type of Residential Use/Occupancy R-2 R-1

Basic

Maximum

Basic

Maximum

R-4 (individual lot/unit

(meters)

(meters)

(meters)

(meters)

(meters)

(meters)

(meters)

Front

4.50

3.00

8.00 *

3.00

8.00 *

4.50

6.00

Side

2.00

2.00 **

2.00 **

***

2.00

2.00

3.00

(optional)

(optional)

2.00

2.00

YARD

Rear

2.00

2.00

R-3

2.00

***

R-5 ****

3.00

Notes: a)

The setback requirements in Table VIII.2. above are for newly-developed subdivisions.

b) *

Total setback only at grade (or natural ground) level, i.e., 3.00 meters + 5.00 meters = 8.00 meters (to accommodate part of the minimum parking requirement outside the designated area for the front yard). The second and upper floors and mezzanine level shall thereafter comply with the minimum

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

138

3.00 meters setback unless otherwise provided under the Code. c) **

Setback required for only one (1) side. Setbacks on two sides shall be optional.

d) ***

Abutments on two sides and rear property lines may be allowed with conditions as enumerated under Section 804, Subsection 10 of this Rule.

e) ****

Mixed-Use Buildings/Structures in R-5 lots shall be considered a commercial use or occupancy if a substantial percentage, i.e., 55% of the Gross Floor Area (GFA) is commercial.

f)

In cases where yards/setbacks are impossible to attain or where frontage and depth of lots are similar to that of Open Market or Medium Cost Housing Projects, abutments on the sides and rear property lines may be allowed and 1.50 meters front yard is left open as transition area.

Table VIII.3. Setbacks for Commercial*, Industrial, Institutional and Recreational Buildings Road Right-of-Way (RROW) WidthFront (meters) (meters) 30.00 & above 25.00 to 29.00 6.00 20.00 to 24.00 5.00 10.00 to 19.00 5.00 Below 10.00 5.00

Side (meters)

Rear (meters)

8.00 3.00 3.00 2.00 2.00

5.00 3.00 3.00 2.00 2.00

5.00

Note: *

Copyright 2010

Mixed-Use Buildings/Structures in R-5 lots may be considered a commercial development if a substantial percentage of the GFA is commercial.

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

139

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

140

STREET/RROW

STREET/RROW

Figure VIII.14.

Figure VIII.15.

Required Open Space Locations 4.

The setback requirements in Table VIII.3. above are for newly-developed thoroughfares. For highly built-up urban areas with duly established lines and grades reflecting therein proposed road widening and elevation, the requirements in Table VIII.3. above may not be imposed and the face of the building may abut on the side and/or rear property lines provided that all the requirements on open space, window opening, artificial ventilation, if any, and firewalls (Rule VII) are first fully complied with.

5.

Every court shall have a width of not less than 2.00 meters for one (1) or two (2) storey buildings. However, if the court is treated as a yard or vice versa, this may be reduced to not less than 1.50 meters in cluster living units such as quadruplexes, rowhouses and the like, with adjacent courts with an area of not less than 3.00 sq. meters. Provided further, that the separation walls or fences, if any, shall not be higher than 2.00 meters. Irregularly-shaped lots such as triangular lots and the like, whose courts may be also triangular in shape may be exempted from having a minimum width of not less than what is required in Table VIII.3. and as shown in Figures VIII.16., VIII.17., VIII.18. and VIII.19. IcDHaT

Copyright 2010

6.

For buildings of more than two (2) storeys in height, the minimum width of the rear or side court shall be increased at the rate of 300 millimeters for each additional storey up to the fourteenth (14th) storey (Figure VIII.20. showing incremental setbacks). For buildings exceeding fourteen (14) storeys in height, the required width of the court shall be computed on the basis of fourteen (14) storeys.

7.

Uncovered Driveways, Access Roads and Parking Spaces may be considered part of the open space provided that they are open and unobstructed from the ground upward as in courts and yards.

8.

A carport shall not be considered part of the Total Open Space

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

141

within Lot (TOSL) particularly if it is entirely roofed or roofed with overhangs. In such a case, it must be counted as an integral component of the Allowable Maximum Building Footprint (AMBF). 9.

A front yard may be partly paved/hardscaped (converted into a courtyard) to serve as a carport but only for a basic R-2 or basic R-3 or R-4 (individual lot) use or occupancy, i.e., all for single-family dwelling units only. All other uses/occupancies shall not be allowed to use the front yard for a carport nor for parking.

10.

For Basic R-3, abutments on two sides and rear property lines may be allowed provided the following requirements are first complied with: a. Open space as prescribed in Reference Table for Maximum PSO, TOSL, and Table VIII.2. of this Rule are satisfied. b. Window opening as prescribed in Section 808 of this Rule are satisfied. c. Firewall with a minimum of two-hour fire-resistive rating constructed with a minimum height clearance of 400 millimeters above the roof. (Figure VIII.21)

11.

Copyright 2010

In case of conflict in the provisions on lighting and ventilation under this Rule or under the Code, the more stringent restrictions must prevail.

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

142

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

143

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

144

SECTION 805. 1.

Habitable rooms provided with artificial ventilation shall have ceiling heights not less than 2.40 meters measured from the floor to the ceiling; provided that for buildings of more than one (1) storey, the minimum ceiling height of the first storey shall be 2.70 meters and that for the second storey 2.40 meters and the succeeding stories shall have an unobstructed typical head-room clearance of not less than 2.10 meters above the finished floor. Above-stated rooms with natural ventilation shall have ceiling heights of not less than 2.70 meters.

2.

Mezzanine floors shall have a clear ceiling height not less than 1.80 meters above and below it.

SECTION 806. 1. Copyright 2010

Ceiling Heights. —

Sizes and Dimensions of Rooms. —

Minimum sizes of rooms and their least horizontal dimensions

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

145

shall be as follows: a.

Rooms for Human Habitations – 6.00 sq. meters with a least dimension of 2.00 meters;

b.

Kitchen — 3.00 sq. meters with a least dimension of 1.50 meters; and

c.

Bath and toilet — 1.20 sq. meters with a least dimension of 900 millimeters.

SECTION 807. Rooms. — 1.

Minimum air space shall be provided as follows: a.

School Rooms — 3.00 cu. meters with 1.00 sq. meter of floor area per person;

b.

Workshop, Factories, and Offices — 12.00 cu. meters of air space per person; and

c.

Habitable Rooms — 14.00 cu. meters of air space per person.

SECTION 808.

Window Openings

1.

Rooms intended for any use, not provided with artificial ventilation system, shall be provided with a window or windows with a total free area of openings equal to at least 10% of the floor area of the room, provided that such opening shall be not less than 1.00 sq. meter. However, toilet and bath rooms, laundry rooms and similar rooms shall be provided with window or windows with an area not less than 1/20 of the floor area of such rooms, provided that such opening shall not be less than 240 sq. millimeters. Such window or windows shall open directly to a court, yard, public street or alley, or open watercourse.

2.

Required windows may open into a roofed porch where the porch: a.

Copyright 2010

Air Space Requirements in Determining the Size of

Abuts a court, yard, public street or alley, or open watercourse and other public open spaces;

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

146

b.

Has a ceiling height of not less than 2.70 meters;

c.

Has one of the longer sides at least 65% open and unobstructed.

3.

Eaves, canopies, awnings (or media ague) over required windows shall not be less than 750 millimeters from the side and rear property lines.

4.

There shall absolutely be no openings on/at/within/through all types of abutments (such as firewalls) erected along property lines except for permitted vent wells. This Rule strictly applies to all new and existing developments.

5.

In locating window openings it should be borne in mind that in cases of extreme emergencies windows must serve as emergency egress to vacate the premises or access for rescue operations. Such windows shall meet the following requirements: a.

They can be opened from the inside without the use of any tools;

b.

The minimum clear opening shall have a width not less than 820 millimeters and a height of 1 meter;

c.

The bottom of the opening should not be more than 820 millimeters from the floor;

d.

Where storm shutters, screens or iron grilles are used, these shall be provided with quick opening mechanism so that they can be readily opened from the inside for emergency egress and shall be so designed that when opened they will not drop to the ground;

e.

All areas immediately outside a fire exit window/grille must be free of obstacles and must lead to a direct access down into the ground or street level.

SECTION 809. 1.

Copyright 2010

Vent Shafts. —

Ventilation or vent shafts shall have a horizontal cross-sectional area of not less than 1.00 sq. meter for every meter of height of shaft but in no case shall the area be less than 1.00 sq. meter.

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

147

No vent shaft shall have its least dimension less than 600 millimeters. 2.

Unless open to the outer air at the top for its full area, vent shafts shall be covered by a skylight having a net free area or fixed louver openings equal to the maximum required shaft area.

3.

Air ducts shall open to a street or court by a horizontal duct or intake. Such duct or intake shall have a minimum unobstructed cross-sectional area of not less than 0.30 sq. meter with a minimum dimension of 300 millimeters. The openings to the duct or intake shall be not less than 300 millimeters above the street surface or level of court. CTAIDE

SECTION 810. 1.

Ventilation Skylights. —

Ventilation skylights shall have a glass area not less than that required for the windows that are replaced. They shall be equipped with movable sashes or louvers with an aggregate net free area not less than the parts in the replaced window that can be opened, or else provide artificial ventilation of equivalent effectiveness.

SECTION 811.

Artificial Ventilation. —

1.

Rooms or spaces housing industrial or heating equipment shall be provided with artificial means of ventilation to prevent excessive accumulation of hot and/or polluted air.

2.

Whenever artificial ventilation is required, the equipment shall be designed to meet the following minimum requirements in air changes as shown in Table VIII.4. hereafter. Table VIII.4. Minimum Requirements for Air Changes

Cubic Meter Per Minute Per Person

Air Changes Per Hour Ceiling Height (meters)

Apartment Banking Space Barber Shop Copyright 2010

CD Technologies Asia, Inc.

Min. 0.29 0.22 0.22

Max. 0.43 0.29 0.29

2.40 3 3 3

Philippine Laws Premium Edition 2009

3.00 2 2 2

3.70 1-1/2 1-1/2 1-1/2

4.90 1 1 1

6.10 3/4 3/4 3/4 148

Beauty Parlor Broker's Board Room Cafeteria Cocktail Bar Churches Department Stores Director's Room Drugstore (no counter) Drugstore (w/counter) Funeral Parlor Gambling Rooms Hospital Room Hotel Room Laboratories Office Restaurant Kitchen Shop, Retail Theaters

3.

0.22 0.57 0.43 0.57 0.14 0.22 0.85 0.22 0.29 0.14 0.57 0.29 0.29 0.43 0.29 0.34 0.22 0.14

0.29 0.85 0.57 0.85 0.22 0.43 0.14 0.29 0.43 0.22 0.85 0.43 0.43 0.57 0.43 0.43 0.29 0.22

3 8 6 8 3 3 8 3 5 3 6 3 3 6 4 5 3 -

6 4-1/2 6 2 2 6 2 3-3/4 2 6 2 2 4-1/2 3 3-3/4 2 -

1-1/2 4-1/2 3-1/2 4-1/2 1-1/2 1-1/2 4-1/2 1-1/2 3 1-1/2 4-1/2 1-1/2 1-1/2 3-1/2 2-1/4 3 1-1/2 -

1 3 2-1/2 3 1 1 3 1 2 1 3 1 1 2-1/2 1-1/2 2 1 -

3/4 2-1/2 1-3/4 2-1/4 3/4 3/4 2-1/4 3/4 1-1/2 3/4 2-1/4 3/4 3/4 1-3/4 1 1-1/2 3/4 -

For other rooms or spaces not specifically covered under this Section, see applicable provisions of the pertinent referral code/s.

EXCEPTION: 1. Variances, exception or deviations from the provision of light and ventilation may be allowed only when the following term and conditions are fully complied with: a.

In case of variances When the property is unique and different from other properties and because of its uniqueness such the owner cannot comply with the open space requirements, variances shall be applied to relax the application of the following provisions: AHECcT

Copyright 2010

CD Technologies Asia, Inc.

i.

setback;

ii.

ventilation and window opening requirements;

iii.

percentage of site occupancy;

iv.

floor area ratio; and

v.

building height limit (BHL).

Philippine Laws Premium Edition 2009

149

At least two (2) conditions must be satisfied for exception to be granted. b.

In case of exceptions i. The exception must not adversely affect public health, safety and welfare and must be in keeping with the general pattern of development in the community. ii. The exception must not alter the essential, character of the district where the exception sought is located, and will be in harmony with the general purpose of this IRR.

Guidelines on Easements, View Corridors/Sight Lines, Streets/Road Right-Of-Way (RROW), Sidewalks, Arcades, Basements, Lots, and Public Buildings/Structures A.

Easements 1.

Copyright 2010

As it is situated outside of private property limits, the easement is public land, i.e., public domain, that should be equally enjoyed by all members of the community. The easement is not to be used for any form of building/structure that may go against its public recreational character and as such, the following uses and others similar thereto are absolutely prohibited: a.

Residential and like uses whether temporary or permanent;

b.

Long-term or overnight vehicle parking, i.e., unless duly designated as day and/or night pay-parking zones;

c.

As a depository of stalled, wrecked or abandoned vehicles, mechanical devices and the like;

d.

The conduct of specific commercial, institutional and/or industrial activities not compatible with its stated character;

e.

Unauthorized recreational or entertainment usage and the like which will only benefit certain entities and which will ultimately result in inconvenience/nuisance/safety problems to the general public; nor

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

150

f.

Any other form of private use, gain, enjoyment or profit at the expense of the motoring or walking public. IEHSDA

2.

Allowed or Encouraged Structures/Developments Within Easements a.

If wider than 9.00 meters, the easement may include a roadway/carriageway component on which vehicles can pass or on which the same may temporarily park, e.g., an esplanade and the like. (Fig. VIII.G.1.)

b.

Pedestrian access-ways and the like and to be located at/above/below the easement may also be developed for public use, e.g., a promenade and the like. (Fig. VIII.G.2.) Table VIII.G.1. Easement* Along Water Bodies/Way by Location

Location of Water Body/Way Urban Areas Agricultural Areas Forest Areas

Easement 3.00 meters per side of waterway (Fig.VIII.G.3.) 20.00 meters per side of waterway 40.00 meters per side of waterway

* Source: Water Code of the Philippines

c.

The allowed structures/developments include: i. Hardscaped (paved) pedestrian access-ways such as walks, footpaths or arcades covered or roofed sidewalks without any habitable structures above or below it); temporary or movable hardscape elements such as gazebos, sheds, fountains and like structures with large footprints must not encroach on the easement; ii. Softscaped (paved) developments such as park strips, linear parks and the like as well as small tree farms are encouraged for recreational, livelihood and soil stabilization/protection purposes;

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

151

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

152

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

153

iii. Concrete steps leading down to the water or wooden boardwalks are allowed, provided that all necessary safety precautions are taken, e.g., non-slip finishing for surfaces, handrails and railings; iv. Other forms of soil stabilization/Protection including anti-erosion/scouring measures/structures within the easement are allowed, e.g., rip-rapping, embankment protection, etc., provided that no enclosed/semi-enclosed habitable structures are built on, above or below such structures; and v. Permanent utility/service lines (power, water, telecommunications, gas, etc.) are allowed within the easement provided that these are either below grade (underground) or above grade (overhead). 3.

Disallowed and Prohibited Structures/Developments Within Easements a. No portion of the easement whether at grade (on the ground), below grade or above grade may be leased or developed by the government or by private entities for purposes inconsistent with its character and intended function. In particular, any form of semi-permanent/permanent or semi-enclosed/enclosed residential, commercial, industrial, institutional or government structure/use and like, structures/uses at any portion of the public easement is prohibited; b. All semi-enclosed or enclosed, semi-permanent or permanent habitable building projections (particularly arcade structures) or any other building projection or structural element (eaves, roof, cantilevered beams, foundations and the like) located above or below the easement are absolutely prohibited; and c. All forms of enclosures such as fences, perimeter walls and the like, intended to limit the use of the easement for private enjoyment/benefit or to restrict full access to the public easement are absolutely prohibited unless the same are erected for reason of public safety.

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

154

B.

View Corridors And/Or Sight Lines 1.

C.

Preservation of View Corridors and/or Sight Lines a.

The carriageway/roadway portion of the RROW shall be free of structures, particularly commercial signs that will impede the view corridor and sight lines within the RROW. (See Fig. VIII.G.4)

b.

To dignify very important public or historical/culture buildings/structures, all forms of commercial signs intruding into RROW leading to or away from such buildings/structures shall not be allowed. Specifically disallowed from such RROW are commercial signs supported from any building projection (such as arcades).

c.

View corridors or sight lines from buildings/structures on a higher or lower lot shall not be entirely blocked by the intervening property to allow some sight lines to exist.

d.

In case of allowed structures within the RROW for transportation, e.g., elevated ramps, fly-overs, tracks, stations, terminals and the like, the appropriate designs shall be adopted to maximize light, ventilation and view.

Streets/Road Right-Of-Way (RROW) 1.

General. No building shall be constructed unless it adjoins or has direct access to public space, yard or street/road on at least one (1) of its sides. All buildings shall face a public street, alley or a road, which has been duly approved by the proper authorities for residential, institutional, commercial and industrial groups. DAaIEc

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

155

a.

Allowed or Encouraged Structures/Developments Within the RROW 1. The RROW a-t all its physical levels may only be used for the following types of structures/uses or others similar to them, to wit: (a) Transportation structures and like uses whether temporary or permanent, e.g., mass transit alignments (particularly light and heavy rail) at grade, mass transit stations and terminal facilities above grade (RROW air rights utilization) or below grade and the like; these also include waiting sheds, traffic outposts and the like; (b) Limited commercial structures/uses above grade (RROW air rights utilization) or below grade provided that these are ancillary or supplementary/complementary to the transportation structures/uses allowed in the previous paragraph, and the like; commercial

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

156

signages on the exterior of the commercial structure are disallowed and prohibited; (c) Improvements on the RROW and on all its components/elements found at all its physical levels, e.g., sidewalks, arcades, roadway/carriageway, medians, planting strips, street furniture, elevated or underground crossings or access-ways, non-commercial traffic and directional signages and the like; and (d) Public utility/service structures/uses (power, water, drainage, sewerage, telecommunications, gas, etc.) at all physical levels of the RROW provided that these do not restrict nor impede the movement of people and vehicles and provided further that the rights to utilize the RROW are properly secured and permitted. b. Disallowed and Prohibited Structures/Developments at RROW 1. If situated outside of private property limits, the RROW is public land, i.e., public domain, which should be equally enjoyed by all members of the community. The RROW is not to be used for the following types of buildings/structures/occupancies or others similar to them: (a) Any form of semi-permanent/permanent or semi-enclosed/enclosed commercial structure/use and like structures/uses; (b) Any form of temporary, semi-permanent/permanent or semi-enclosed/enclosed residential structure/use and like structures/uses; (c) Government structures/use unless the same are located below or above grade; in such cases, the proposed structure must be properly planned/designed and constructed;

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

157

(d) Long-term or overnight vehicle parking, i.e., unless duly designated as day and/or night pay-parking zones; (e) As a depository of stalled, wrecked or abandoned vehicles, mechanical devices and the like; (f) The conduct of other commercial/business/industrial activities incompatible with the character of the RROW; (g) Unauthorized recreational or entertainment usage and the like which will only benefit certain entities and which will ultimately result in inconvenience/nuisance/safety problems to the general public; nor (h) Any other form of private use, gain, enjoyment or profit at the expense of the motoring or walking public. Table VIII.G.2. Suggested Median and Lane Widths Within Alleys/Roadways/Carriageways by Minimum RROW Width and by Suggested Vehicle Speeds Range of Total Suggested Alley or RROW Minimum Required Width (meters) Width of Alley or Roadway/Carriageway Maximum (meters) Vehicle Speeds Along Alley or Roadway (kilometers/hour) 2.00 (for 3.00 meters Alley ROW) 3.00 to 6.00 4.00 (for 6.00 meters RROW) 4.81 (for 6.01 meters RROW) Copyright 2010

CD Technologies Asia, Inc.

Range of Suggested Minimum to Median Widths (meters)

1.00 to 15.00

16.00 to 30.00

Philippine Laws Premium Edition 2009

Suggested Minimum to Maximum Lane Widths (meters)

Suggested Minimum to Maximum

None

2.00 one way car passage

None

2.10 each way

None

2.40 each way 158

6.10 to 20.00 13.40 (for 20.00 meters RROW) 13.50 (for 20.10 meters RROW)

1.20 to 2.00 2.80 to 3.00

31.00 to 60.00

1.20 to 4.50 1.20 to 4.80

20.10 to 40.00 26.80 (for 40.00 meters RROW) 26.90 (for 40.10 meters RROW)

40.10 to 60.00 and above

3.00 to 3.30

61.00 and above

40.00 (for 60.00 meters RROW)

c.

3.3 to 3.50

1.50 to 5.00 1.50 to 5.50

3.50 to 3.80 3.80 to 4.00

Minimum Access Requirements i. RROW/access streets or alleys shall have the following widths: (a) Interior or rear lots shall have a RROW/access street with a minimum width depending upon the number of buildings or units which it serves provided, however, that said RROW/access street shall not be less than 3.00 meters in width and provided further that such RROW shall be provided with a minimum 4.00 meters wide chaflan at its intersect with the main RROW and provided, finally, that such RROW shall not be used for any form of parking. (b) Multiple living units on same lot on which apartments, rowhouses or accessories or a group of single-detached buildings are built be provided with a RROW/access street directly connecting said buildings or units to a public street/road or alley following the schedule as shown in Table VIII.G.3. EACIaT

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

159

(c) For commercial or industrial areas, sufficient lane widths, shoulders and maneuvering spaces for long-bodied/articulated vehicles should be considered within the RROW. (d) Privately-owned BROW/access streets shall be duly registered and annotated in the lot title as such for as long as the apartments, rowhouses, etc., using said RROW/access streets, still exist. (e) Alignment of RROW/access streets shall be integrated into the existing street/road network, particularly with the provision of chaflans of the appropriate width. (f) No obstruction should exist within the RROW/access streets servicing multiple housing of more than 75 units. (g) All kinds of subdivisions and residential condominiums may generally refer to this Guideline concerning access streets/roadways. (Figs. VIII.G.5. through VIII.G.10.) Table VIII.G.3. Minimum Road Right-of-Way (RROW) Provisions for Developments with Multiple Dwelling Units Minimum Number of Dwelling Units

Minimum Minimum Width of Width of Total Width Carriageway/Roadway Sidewalk of the (meters) on each side RROW (meters) (meters)

Up to six (6) units Seven (7) up to fifteen (15) units Sixteen, (16) up to Twenty-five (25) units Twenty-six (26) up to Thirty-five (35) units More than thirty-five (35) units

d.

3.00 4.00 5.00 6.00 6.70

0.60 1.00 1.00 1.00 1.00

4.20 6.00 7.00 8.00 8.70

The RROW consists of three (3) different physical levels as follows: i. RROW ABOVE GRADE — refers to the portion of the RROW reckoned from the finished surface of the

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

160

roadway/carriageway and/or the sidewalk/arcade all the way up to the air. If this level of the RROW is utilized for whatever purpose, the Air Rights or the right to develop, benefit and profit from the use of the BROW above grade is given up by the government/general public and should therefore be compensated, i.e., leased and paid for by the proponent/end-user/beneficiary of the proposed building/structure (Figs. VIII.G.11. and VIII.G.12.). The minimum clear height for the utilization of air rights above RROW shall be 4.27 meters from the finished crown elevation of the roadway/carriageway. ii. RROW AT GRADE — refers to the portion of the RROW reckoned from the natural grade line up to the finished surface of the roadway/carriageway and/or the sidewalk/arcade. This portion of the RROW is generally utilized for the movement of the general public (motorists and pedestrians). If this level of the RROW is utilized for whatever purpose, the right to develop, benefit and profit from the use of the RROW at grade is given up by the government/general public and should therefore be compensated, i.e., leased and paid for by the development proponent/end-user/beneficiary. (Figs. VIII.G.11. and VIII.G.12.) iii. RROW BELOW GRADE — refers to the portion of the RROW reckoned from the finished surface of the roadway and/or the sidewalk all the way down into the ground. If this level of the RROW is utilized for whatever purpose, the right to develop, benefit and profit from the use of the RROW below grade is given up by the government/general public and should therefore be compensated, i.e., leased and paid for by the development proponent/end-user/beneficiary. (Figs. VIII.G.11. and VIII.G.12.)

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

161

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

162

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

163

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

164

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

165

D.

Sidewalks 1.

Subject to existing laws and regulations, the local planning authority shall determine which street shall have an open sidewalk or an arcaded (covered) sidewalk, or a combination of both.

2.

The minimum width of the sidewalk for a RROW width of 9.00 meters or more shall be 1.20 meters on each side of the RROW or a total of 2.40 meters on both sides of the RROW (Fig. VIII.G.14.). For the minimum width of sidewalk for RROW of less than 9.00 meters wide, refer to Table VIII.G.3.

3.

Sidewalk widths shall be based on the following considerations: a.

Volume of pedestrians (end-users, visitors and the like) who will use the sidewalk on a regular basis;

b.

Type, intensity or level of operation and size/expanse of the allowed uses/occupancies along the RROW;

c.

The types and volume of street furniture, e.g., street lighting and traffic signs/signal supports, pedestrian barriers/aids, etc., and other urban design elements that will be allowed as permanent developments design elements that will be allowed as permanent developments within the width of the sidewalk; IASEca

Copyright 2010

d.

The width of the planting strips;

e.

The spatial needs for servicing utility/service lines underneath the sidewalk and for utility/service poles;

f.

Compliance with accessibility requirements as stipulated under Batas Pambansa Blg. 344 (Accessibility Law);

g.

Provisions for commuters, e.g., loading/unloading areas and the like;

h.

Provisions for vehicle crossings/driveways between the roadway/carriageway and the front yards of lots or buildings/structures or provisions for loading/unloading platforms if allowed;

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

waiting

sheds,

166

i.

Need for introduction of allowed uses/elements within the sidewalk area only if there is sufficient sidewalk width, e.g., bicycle lanes, jogging lanes and the like; and

j.

Climate, light, ventilation, safety, security and overall maintenance of the sidewalk and all its surface areas.

4.

Sidewalks shall be of uniform width throughout the entire length of the street. The sidewalk width grade and finish of the dominant use/occupancy along the RROW shall be generally observed.

5.

The width of the sidewalk shall be as follows:

Table VIII.G.4. Range of Required Sidewalk and Planting Strip Widths (total at both sides of RROW) by RROW Width Road Right-Of-Way (RROW) Width

Range of Required Sidewalk Widths (Total at both sides of RROW)

30.00 meters & above 25.00 - 29.00 meters 20.00 - 24.00 meters 10.00 - 19.00 meters Below 10.00 meters

From 1/6 up to 1/4 of RROW Width From 1/6 up to 1/3 of RROW Width From 1/6 up to 1/3 of RROW Width From 1/4 up to 1/3 of RROW Width From 1/4 up to 1/3 of RROW Width

6.

The width of the sidewalk shall include both the paved and unpaved (planted) portions. (see Table VIII.G.5.) Table VIII.G.5. Minimum Planting Strip Widths by RROW Width

Road Right-Of-Way (RROW) Width 30.00 meters & above 25.00 - 29.00 meters 20.00 - 24.00 meters 10.00 - 19.00 meters Below 10.00 meters Copyright 2010

CD Technologies Asia, Inc.

Total Minimum Widths of Planting Strip within RROW* (width per sides of RROW) (meters) 1.20 (0.60) 0.60 (0.30) 0.60 (0.30) 0.40 (0.20) Optional Philippine Laws Premium Edition 2009

167

Note: *

Minimum width of planting strip (for grass and shrubs) is 200 millimeters for each side of the RROW The minimum width of planting strip (for trees) is 300 millimeters for each side of the RROW.

7.

For allowed, disallowed and prohibited structures/developments at RROW, refer to Sections C.1. (a) and C.1. (b) of this Guideline.

8.

The sidewalk pavement shall have a non-slip surface and shall slope down from the building line towards the curb line at not more than 1/50 and shall level off with the curb. (Fig. VIII.G.14.)

9.

Sidewalks of 2.00 meters or more in width shall include on its outer side a planting strip of not less than 800 millimeters in width up to a maximum of 1/3 of the allowed sidewalk width, separating the curb from the sidewalk pavement. The planting strip must always be near the curbline. (Fig. VIII.G.15.) TcaAID

Copyright 2010

10.

Combined open and arcaded sidewalks shall be provided with a planting strip of not less than 800 millimeters in width up to a maximum of 1/3 of the allowed sidewalk width, as a separating strip between the arcaded portion and the open portion of the sidewalk. (Fig. VIII.G.16.)

11.

Grade of Sidewalks a.

Sidewalks shall, as much as possible, be level and of uniform grade throughout the entire length of the street.

b.

Whenever the slope of the street does not exceed 1/12 the sidewalk grade shall follow the level or slope of the street. (Fig. VIII.G.17.)

c.

Whenever the slope of the street is 1/10, the sidewalk shall be maintained level for every 20.00 to 40.00 meters of run (Fig. VIII.G.18.). Sidewalks of different levels shall be joined by means of a ramp having any convenient slope not exceeding 1/6. (Fig. VIII.G.18.)

d.

When the grade of two (2) connecting sidewalks are between 1/10 and 1/8, the two sidewalks shall be joined

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

168

by means of a ramp having any convenient slope not exceeding 1/10.

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

169

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

170

Grade Of Sidewalks 12.

Driveways, Entrances and Exits a.

Driveways Across Sidewalks i. To maximize the use of the sidewalk area, the surface of the sidewalk and the driveway shall as much as possible, be at the same plane. The entry ramp of the driveway connecting the roadway surface to the sidewalk surface shall have a slope ranging from 1/3 to 1/4. (Figs. VIII.G.19. and VIII.G.20.) ii. Whenever the height of the curb is more than 200 millimeters, driveways may be constructed across the entire width of the sidewalk, provided that the driveway shall be joined to the sidewalk by means of a ramp of rough finish have a slope of not more than 1/8. The driveway and the ramp shall be made of the same materials as that of the sidewalk. (Figs. VIII.G.19., VIII.G.20., and VIII.G.21.) iii. Entrances and exits of buildings abutting sidewalks shall be made of either ramps or steps. iv. Entrance and exits ramps shall have a slope not exceeding 1/10. (Fig. VIII.G.22.) v. Entrance or exit steps shall have treads of not less than 300 millimeters. The minimum number of steps shall be two (2) with risers not exceeding 100 millimeters. vi. No portion of either entrance or exit ramps or steps shall intrude into the sidewalk pavement.

13.

Obstruction on Sidewalks a.

Copyright 2010

Under no circumstances shall obstruction of any kind be allowed on sidewalks, whether open or arcaded. This specifically refers to all forms of commercial signs and commercial structures that impede sight lines or pedestrian traffic along the sidewalk.

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

171

b.

14.

Copyright 2010

Planted areas forming part of the sidewalk or arcade shall not be fenced in to allow passage of pedestrians and disabled in transit.

Curb Configurations a.

Mountable curbs shall only be allowed if the sidewalk width on each side of the RROW is at a minimum of 5.00 meters wide.

b.

For greater protection of pedestrians and the disabled, raised curbs are encouraged for use along sidewalks that are less than 5.00 meters in width.

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

172

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

173

E.

Total Open Space Requirements on Lots by Use/Occupancy, Type/Location and Suggested minimum Sizes, Lot Dimensions & Types By Use/Occupancy Table VIII.G.6.

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

174

Minimum TOSL Requirements by Lot Type/Location Note: Higher Percentages (%) may apply for lots with Minimum Total Lot Area (TLA) MINIMUM PERCENTAGE OF OPEN SPACE BY OCCUPANCY TYPE** (for Proposed Developments LOT

MINIMUM PERCENTAGE OF OPEN SPACE BY OCCUPANCY TYPE** (for Proposed Developments

without Firewalls Abutments) with Permitted Firewalls or Allowed Abutments

TYPE/LOCATION* A&B Other (Cultural) E-1 and E-3

H-1, H-2, H-4

All Other

A&B

H-1, H-2, H-4All

(Residential or Uses/ Institutional) Occupancy & C, D, E-2

and I (Cultural

Uses/

(Residential orand I

and E-1 and E-3

Occupancy

Institutional) &and

(Transportation/Utility)

C, D, E-2 and

(Transportation/ and H (Institutional Interior or Rear Lot (Lot cultural located in the interior of a block made accessible from a public street or alley by transportation mean sofa utility/services) private access road); see Figure VIII.2.

H (Institutional Utility)

40% 15% (for R-1 use or

(for all classes

occupancy only),

of cultural use or occupancy)

30% (for R-2 use or occupancy only

and 50% (for all classes

20%*** (for other

and

of

residential)

30% (for other residential uses or occupancy); and

40%

20%

*

30%

(for all

25%** (for R-2) 40%## (for all

transportation/ utility use or occupancy)

40%**** (for all institutional)

50% (for all classes of institutional uses or occupancy) Inside Lot otherwise cultural) referred to as a Regular Lot (Noncorner or single frontage lot); see Figure VIII.3. transportation/

Copyright 2010

CD Technologies Asia, Inc.

50% 15% (for R-1 use or

40% (for all classes

occupancy only),

of cultural use or occupancy)

40% (for R-2 use or occupancy only) and

and

25%

* (for all

30% (for R-2)

50% for all classes of transportation

20%**

/utility use

(for other

Philippine Laws Premium Edition 2009

30%#

40%## (for all

175

utility/services) 30% (for other residential uses

or occupancy)

residential

or occupancy); and

40%**** (for all institutional)

50% (for all classes of institutional uses or occupancy) Corner Lot+ or Through cultural) Lot; see Figures VIII.4. and VIII.5.

30% 10% (for R-1 and all

36% (for all classes

other residential uses or occupancy);

of cultural use or occupancy)

20%

30%#

(for all 25%** (for R-2) 20%*** (for other residential)

and and

+Note: For corner lots, the largest setback transportation/ requirement utility/services) shall apply to the two (2) sides serviced by

*

40% (for all classes of institutional

40% (for all classes of transportation/ utility use or

30%**** (for all

uses or

occupancy)

institutional)

30%## (for all

occupancy)

the RROW. End Lots bounded on cultural) two (2) or more sides by the property line of the subdivision or by public open spaces such as transportation/ easements utility/services) of lake/sea-shores, rivers, esteros, etc. and accessible only through one (1) side of the lot; see Figure VIII.8. Copyright 2010

CD Technologies Asia, Inc.

40% 15% (for R-1 use or

(for all classes

occupancy only),

of cultural use or occupancy)

30% (for R-2 use or occupancy only) and

and

30%

40%

20%

*

30%#

(for all

25%** (for R-2)

50% (for all classes of transportation/ utility use or

20%*** (for other

occupancy)

residential)

40%## (for all

(for other residential uses or occupancy) and 5% (for all classes of institutional uses or Philippine Laws Premium Edition 2009

40%**** (for all institutional) 176

occupancy) Corner-Through Lots or Corner cultural) Lots+ abutting three (3) or more public open spaces such as streets, alleys, easement of lake/sea-shores, rivers, esteros, etc.; see Figures transportation/ VIII.6. and utility/services) VIII.7. +Note: For corner lots, the largest setback requirement shall apply to the two (2) sides serviced

30% 5% (for R-1 and all other residential and commercial uses or occupancy)

36%

10%

*

30%#

(for all classes

(for all

of cultural use or occupancy)

25%** (for R-2) 20%*** (for other residential and commercial) 30%## (for all 30%****

and and 40% (for all classes

40% (for all classes of transportation/

of institutional

utility use or

(for all

uses or occupancy)

occupancy

institutional)

by the RROW. Notes: *

with absolutely of firewalls/abutments allowed for R-1 use.

**

with firewall/abutment allowed on only one (1) side property line and absolutely no firewall/abutment

at front and rear property lines for R-2 use. *** with firewalls/abutments allowed on two (2) side property lines only or on one (1) side property line and the rear property line and absolutely no firewall/abutment at front property lines for R-3 and R-5 uses; and with firewalls/abutments allowed on two (2) side property lines only and absolutely no firewall/abutment at the front and rear property lines for R-4 use. **** with firewalls/abutments for all classes of institutional uses. #

with firewall/abutment allowed on only one (1) side for all classes of cultural uses.

## with firewalls/abutments allowed on two (2) sides only or on one (1) side and rear boundary for all classes of transportation/utility uses. +

Refer to Rule VIII-Figures VIII.2. through VIII.8 for lot type/location.

++ Refer to Rule VII for occupancy grouping.

Table VIII.G.7 Suggested Minimum Lot Sizes, Lot Dimensions and Types by Use or Occupancy Use or Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

177

Occupancy (preferably based on Duly-Approved Local Zoning

Lot Location Type

Ordinance) Interior

Inside

Corner

(or Rear)

(or Regular)

Lot or

Lot

Lot

Through Lot

End Lot

Corner-Through Lot or

Corner Lot

Abutting 3 or More Streets, etc. (See Rule VIII-

(See Rule VIII-

(See Rule VIII-

(See Rule VIII-

Figure VIII.2)

Figure VIII.3.

Figures

Figure VIII.8.

Rivers, etc. (See Rule VIIIVIII.4. & VIII.5.

Figs.

VIII.6. & VIII.7.) Residential 1 365.00 sq. (R-1)

301.00 sq.

301.00 sq.

365.00 sq.

548.00 sq.

meters

meters

meters

meters

14.00 meters wide (w) x 14.00 meters deep (d)

17.00 meters (w) x21.50 meters (d)

25.50 meters (w) x21.50 meters (d)

Not

80.00 sq.

96.00 sq

140.00 sq.

Allowed

meters

meters

meters

800 meters

9.60 meters

14.00 meters

(w) x10.00 meters (d)

(w) x10.00 meters (d)

(w) (w) x10.00 x10.00 meters (d)

Not

192.00 sq.

261.00 sq.

378.00 sq.

Allowed

meters

meters

meters

12.00 meters

14.50 meters

21.00 meters

(w) x16.00 meters (d)

(w) x18.00 meters (d)

meters 21.50 meters

17.00 meters (W) (W) x21.50 x21.50 meters (d)

meters (d) Basic 96.00 sq. Residential 2 meters (R-2) Medium Density Housing (single 9.60 meters family dwelling unit with a BHL of 10.00 meters) meters (d) Maximum 261.00 sq. R-2 meters Medium Density Housing (multiple family dwelling 14.50 meters units within one building/structure with a BHL of 15.00 Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

(w) (w) x18.00 x18.00 meters (d) 178

meters (d) meters Basic 75.00 sq. Residential 3 meters (R-3) High Density Housing (single 6.00 meters family dwelling unit with a BHL of 10.00 meters)

Not

50.00 sq.

75.00 sq.

200.00 sq.

Allowed

meters

meters

meters

4.00 meters

6.00 meters

16.00 meters

(w) x12.50 meters (d)

(w) x12.50 meters (d)

(w) (w) x12.50 x12.50 meters (d)

Not

400.00 sq.

475.00 sq.

700.00 sq.

Allowed

meters

meters

meters

16.00 meters

19.00 meters

28.00 meters

(w) x25.00 meters (d)

(w) x25.00 meters (d)

(w) (w) x25.00 x25.00 meters (d)

Not

96.00 sq.

120.00 sq.

180.00 sq.

Allowed

meters

meters

meters

8.00 meters

10.00 meters

15.00 meters

(w) x12.00 meters (d)

(w) x12.00 meters (d)

(w) (w) x12.00 x12.00 meters (d)

Not

500.00 sq.

540.00 sq.

945.00 sq.

Allowed

meters

meters

meters

18.50 meters

20.00 meters (w) x27.00 meters (d)

35.00 meters (w) x27.00 meters (d)

Not

204.00 sq.

238.00 sq.

Allowed

meters

meters

12.00 meters

14.00 meters (w)

(w)

meters (d) Maximum R-3 475.00 sq. High Density meters Housing (multiple 19.00 meters Family dwelling units within one building/structure with meters (d) BHL of 36.00 m) Residential 4 120.00 sq. (R-4) meters individual Townhouse Lots 10.00 meters

meters (d) Residential 5 540.00 sq. (R-5) meters 20.00 meters (w) (w) x27.00 x27.00 meters (d)

meters (d) Commercial 1 sq. (Com-1)

Not238.00 Allowed

meters

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

14.00 meters (w) 179

x17.00

x17.00

meters (d)

meters (d)

Not

301.00 sq.

365.00 sq.

Allowed

meters

meters

14.00 meters

17.00 meters (w) x21.50

(w) x21.50

meters (d)

meters (d)

Not

600.00 sq.

813.00 sq.

Allowed

meters

meters

20.00 meters

25.00 meters (w) x30.00

(w) x32.00

meters (d)

meters (d)

Commercial 2 sq. (Com-2)

x17.00 meters (d) Not365.00 Allowed

meters

Commercial 3* sq. (Com-3)

17.00 meters (w) x21.50 meters (d) Not813.00 Allowed

meters 25.00 meters (w) x32.00 meters (d)

Note: *

Suggested minimum lot sizes, lot dimensions, types and restrictions for Commercial 3 (C-3) Lots may

also apply to industrial (I), General Institutional (GI) and Cultural (C) Uses or Occupations.

F.

Basements 1.

Maximum Configuration of Basement Levels While basements may be developed for medium to very high density residential, commercial, institutional and mixed-use developments, its planning, design and construction shall observe the following limitations:

Copyright 2010

a.

The minimum road right-of-way (RROW) width that services the lot on which the basement can be constructed should be at least 10.00 meters wide;

b.

For basements to be allowed, the prescribed setbacks and yards must be satisfied for the building/structure above grade inasmuch as the very same setbacks shall apply below grade to determine the maximum depth or width of the basement level;

c.

If the Code prescriptions for introducing natural light and ventilation into all basement levels are first satisfied (refer to Fig. VIII.G.23.), the maximum depth of the

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

180

basement can then be made equal to one-half of the height of the building above grade; if the prescriptions for natural lighting and ventilation are satisfied, the basement depth can therefore be as much as one-third of the combined height of the building to be constructed above grade and below grade; HcDATC

2.

d.

The center portion of all basement levels shall be reserved for the satisfaction of the basement level may extend by a minimum clear distance of 1.40 meters from the outermost face of the building (OFB) at grade level;

e.

The OFB at the second and lower basement levels shall follow the line of the OFB at grade level; and

f.

All drainage structures below grade shall not exceed the OFB below grade.

Minimum Provisions for Natural Lighting and Ventilation at Basement Levels If basements are to be developed, the following minimum provisions for natural light and ventilation shall be satisfied:

Copyright 2010

a.

A primary or main natural light and ventilation shaft (vertical) with a clear distance of at least 3.00 meters shall be located at the center of the building and shall traverse the entire combined height of the building above and below grade; (refer to Fig. VIII.G.23)

b.

Secondary or support natural light and ventilation shaft/s (angular) with a clear distance of at least 1.20 meters shall emanate from the front and rear perimeters of the building and shall traverse the entire depth of the basement; the angular shaft/s shall be at an angle of 60° from the horizontal, consistent with the maximum Philippine solar angle; separate angular shafts emanating from the side perimeters of the building are encouraged; and

c.

Both the vertical and angular shafts shall only be used for natural air and light intake and shall not be used for any form of exhaust or air exchange to keep the

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

181

temperature inside the shafts at a minimum.

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

182

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

183

G.

Design Of Public Buildings/Structures 1.

Copyright 2010

General a.

Public buildings/structures are permanent edifices owned by the government, whether national or local, its agencies, including government owned and/or controlled corporations.

b.

Design of public buildings/structures shall conform to the applicable provisions of the preceding rules and regulations. Aside from being logically functional and structurally sound, should promote, enhance and express the aesthetic presentability, customs and traditions, socio-economic values environmental quality and cultural heritage of the region concerned towards evolving a distinct Filipino Architecture.

c.

The architectural character of public buildings/structures must fully express the nature of their function, use or occupancy and should reflect their identity as public buildings/structures compatible with their total macro and micro-environment.

d.

Public buildings/structures should be designed for permanence but with maximized flexibility to allow for future adjustments in their uses/occupancies.

e.

Use of indigenous and/or locally manufactured/produced materials such as marble, stone, adobe, clay tiles, wood, coco wood, kapis shells, should be maximized unless their production or usage are banned or regulated by the government to promote the efforts to conserve natural resources.

f.

Use of natural light and ventilation by means of proper orientation, cross ventilation, convection, sun control devices and the like should be maximized.

g.

Choice of finishes should aim to minimize maintenance costs.

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

184

2.

Copyright 2010

h.

The architectural plan and design must basically reflect the functional manner or spatial utilization and/or the evolving Filipino, Asian or International usage of spaces that need to be projected if required or used, more than just attention to pure forms/images.

i.

Only the use of good to high quality materials, labor, technologies and construction methods within the approved budget, must be specified by its planners and designers to ensure permanence, long continued use and low maintenance cost of public buildings or structures.

j.

Plans and designs of all public buildings must fully comply with all of the planning and design requirements under the Code and this IRR including the Fire Code of the Philippines and the Accessibility Law (B.P. Blg. 344).

k.

Strictly consider proper landscaping analysis and design not only for aesthetics but more so for the prevention of erosion of its site and immediate vicinity, and for ecological balance.

l.

These requirements are not intended to limit the creativity of the designer nor preclude the use of advanced or innovative technology particularly in instances wherein mandated compliance under this Guideline shall present a major difficulty in or hamper the proper execution of the plan, design or architectural concept.

Site Selection a.

Where a project site is yet to be selected, the potential site must be compatible with the project usage. The site should be accessible, and near power, water, sewerage, drainage as well as transportation, communication and solid waste management system for practical and economic considerations.

b.

Site analysis should show an accurate and thorough understanding of the site. It should include, but not limited to, consideration of topography, point of access,

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

185

existing buildings/structures/utilities/services, trees, soil characteristics, existing and approved land uses, views and vulnerabilities to flooding, erosion, seismic activity or other threats. c.

3.

The site must be properly and completely described, clearly defining its technical boundaries, showing access thereto such as highway, road or alley and indicating easements, encroachments, approved building lines, proposed road widening, existing buildings/structures, utilities/services and trees. For site on rolling grounds or steep slope, its contour lines must be shown at convenient intervals.

Site Development a.

Location and Orientation — Locate and orient the buildings to maximize the use of natural ventilation and lighting and minimize energy consumption within the constraints of the functional requirements, the topography and site configuration. North-south exposure of buildings has the advantage of maximizing the cooling effect of prevailing winds coming from the southeasterly and southwesterly directions. Such exposures minimize the effect of afternoon solar heat at the same time.

b.

Site Drainage — Drainage is a basic site design consideration and must be done in conjunction with siting and orientation of buildings, location of parking lots and roads, consideration of topography and compliance with functional site requirements. Parking lots, roads and walks must be graded to assure positive drainage for each major site element and must be coordinated into a total drainage system. Existing drainage ways, if any, should be utilized to retain the original character of the site and to avoid unnecessary earthwork. aDICET

c.

Copyright 2010

Grading Design — Balance the cut and fill for the entire site as closely as possible to eliminate the need for hauling earth on or off the site. If topography for areas required for parking, roadways and other site features

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

186

require cut and fill, selection of finished elevations for backfilling of the entire site should be well studied and appropriate. d.

Vehicular and Pedestrian Access and Circulation — Access and circulation patterns to and within the site must be studied in the process of site planning. Easy and direct access and smooth circulation should be provided for vehicles and pedestrians including for disabled persons.

e.

Site Utilities and Services — Provide adequate underground utilities and services such as concrete or masonry trench with retractable covers for maintenance and avoid diggings of new roads. The trench alignments shall be coordinated with paving of roads and landscape, including future extensions, to avoid conflicts with these site elements. Provide most economical run, and minimize the possibility of utility relocation. Coordinate the location of underground site utilities and services such as power, water supply, sewerage communications and drainage systems to reduce the possibility of utility/service crossing and contamination. RULE IX Sanitation

SECTION 901.

General Requirements. —

Subject to the provisions of Book II of the Civil Code of the Philippines on Property, Ownership, and its Modification, all buildings hereafter erected, altered, remodeled, relocated or repaired for human habitation shall be provided with adequate and potable water supply, plumbing installation, and suitable wastewater treatment or disposal system, storm water drainage, pest and vermin control, noise abatement device, and such other measures required for the protection and promotion of health of persons occupying the premises and others living nearby. SECTION 902. 1.

Copyright 2010

Water Supply System. —

Whenever available, the potable water requirements for a building used for human habitation shall be supplied from existing municipal or city waterworks system.

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

187

2.

The quality of drinking water from meteoric, surface or underground sources shall conform to the criteria set in the latest approved National Standards for Drinking Water Standards.

3.

The design, construction and operation of deepwells for the abstraction of groundwater shall be subject to the provisions of the Water Code of the Philippines (PD 1067).

4.

The design, construction and operation of independent waterwork systems of private housing subdivisions or industrial estates shall be governed by existing laws relating to local waterworks system.

5.

The water piping installation for water supply and distribution to each fixture including the wastewater drainage with proper venting inside building and premises, shall conform to the provision of the Revised National Plumbing Code of the Philippines.

SECTION 903. 1.

Sanitary sewage from buildings and neutralized or pre-treated industrial wastewater shall be discharged directly into the nearest street sanitary sewer main of existing municipal or city sanitary sewerage system in accordance with the criteria set by the Code on Sanitation of the Philippines and the Department of Environment and Natural Resources (DENR).

2.

All buildings located in areas where there are no available sanitary sewerage system shall dispose their sewage to "Imhoff" or septic tank and subsurface absorption field or to a suitable waste water treatment plant or disposal system in accordance with the Code on Sanitation of the Philippines and the Revised National Plumbing Code of the Philippines.

3.

Sanitary and Industrial plumbing installations inside buildings and premises shall conform to the provisions of the Revised National Plumbing Code of the Philippines.

SECTION 904. 1. Copyright 2010

Wastewater Disposal System. —

Storm Drainage System. —

Rainwater drainage shall not discharge to the sanitary sewer

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

188

system. 2.

Adequate provisions shall be made to drain rainwater from low areas in buildings and their premises.

3.

The drainage pipe installation and sewerage system of any premises and/or connection with any public disposal or any acceptable terminal shall conform to the Revised National Plumbing Code of the Philippines.

SECTION 905.

Pest and Vermin Control. —

1.

All buildings with hollow and/or wood construction shall be provided with rat-proofing.

2.

Garbage bins and receptacles shall be provided with ready means for cleaning and with positive protection against entry of pests and vermins.

3.

Dining rooms for public use without artificial ventilation shall be properly screened.

SECTION 906.

Noise Pollution Control. —

1.

Industrial establishments shall be provided with positive noise abatement devices to tone down the noise level of equipment and machineries to acceptable limits set down by the Department of Labor and Employment and the Department of Environment and Natural Resources.

2.

Noise as an unwanted sound both in quality and intensity and excessive vibration whose sources in building/structure construction shall conform to acceptable limits the required emission standards of DENR.

SECTION 907.

Pipes Materials. —

All pipe materials to be used in buildings/structures shall conform to the standard specifications of the Bureau of Product Standards (BPS) of the Department of Trade and Industry (DTI). RULE X Building Projection Over Public Streets Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

189

SECTION 1001. General Requirements. — 1.

No part of any building or structure or any of its appendages, shall project beyond the building line except as provided herein.

2.

The projection of any structure or appendage over a public property shall be the distance measured horizontally from the property line to the outermost point of the projection.

SECTION 1002. Projection Into Alleys or Streets. — 1.

No part of any structure or its appendage shall project into any alley or street, national road or public highway except as provided in the Code.

2.

Footings located at least 2.40 meters below grade along national roads or public highway may project not more than 300 millimeters beyond the property line provided that said projection shall not obstruct any existing utilities/services such as power, water, sewer, gas, communication, and drainage lines, etc., unless the owner concerned shall pay the corresponding entities for the rerouting of the parts of the affected utilities. ECDHIc

3.

Foundations may be permitted to encroach into public sidewalk areas to a width not exceeding 500 millimeters; provided that the top of the said foundation is not less than 600 millimeters below the established grade; and provided further, that said projection shall not obstruct any existing utilities/services such as power, water, sewer, gas, communication and drainage lines, etc., unless the owner concerned shall pay the corresponding entities for the rerouting of the parts of the affected utilities.

SECTION 1003. Projection of Balconies and Appendages Over Streets. — 1.

The extent of any projection over an alley or street shall be uniform within a block and shall conform to the limitations set forth in Table X.1. as shown below: TABLE X.1. Projection of Balconies and Appendages

Copyright 2010

Width of Streets

Total Projections

Over 3.00 meters but less than 6.00 meters

.60 meter

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

190

6.00 meters to less than 10.00 meters 10.00 meters to less than 11.00 meters 11.00 meters to less than 12.00 meters 12.00 meters to toss than 13.00 meters 13.00 meters to less than 14.00 meters 14.00 meters or over

.90 meter 1.00 meter 1.10 meters 1.30 meters 1.40 meters 1.50 meters

2.

The clearance between the established grade of the street and/or sidewalk and the lowest under surface of any part of the balcony shall not be less than 3.00 meters.

3.

In case the projection is a neon sign and the like, the same shall be in accordance with Rule XX - Signs.

SECTION 1004. Arcades

Copyright 2010

1.

Whenever required by existing building and zoning regulations, arcades shall be constructed on sidewalks of streets. The width of the arcade and its height shall be uniform throughout the street provided that in no case, shall an arcade be less than 3.00 meters above the established sidewalk grade. (Fig. X.1.)

2.

Arcaded pedestrian walkways shall have a clear height of 3.00 meters. (Fig. X.1.)

3.

Driveways crossing arcaded pedestrian walkways shall be at the same level with that of the arcades for the safety of the pedestrians. (Fig. X.2.)

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

191

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

192

Arcades SECTION 1005. Canopies (Marquees) 1.

Canopy or Marquee is a permanent roofed structure above a door attached to and supported by the building and projecting over a wall or sidewalk. This includes any object or decoration attached thereto.

2.

Projection and Clearances. The horizontal clearance between the outermost edge of the marquee and the curb line shall be not less than 300 millimeters. The vertical clearance between the pavement or ground line and the undersurface of any part the marquee shall not be less than 3.00 meters.

3.

Construction. A marquee shall be constructed of incombustible material or materials of not less than two-hours fire-resistive construction. It shall be provided with necessary drainage facility.

4.

Location. Every marquee shall be so located as not to interfere with the operation of any exterior standpipe connection or to obstruct the clear passage from stairway exits from the building or the installation or maintenance of electroliers. STaCcA

SECTION 1006. Movable Awnings or Hoods. — 1.

Awning is a movable shelter supported entirely from an exterior wall of a building and of a type which can be retracted, folded, or collapsed against the face of a supporting building.

2.

Clearance. The horizontal clearance between the awning and the curb line shall not be less than 300 millimeters. The vertical clearance between the undermost surface of the awning and the pavement or ground line shall be not less than 2.40 meters. Collapsible awnings shall be so designated that they shall not block a required exit when collapsed or folded.

SECTION 1007. Doors, Windows, and the Like. — Doors, windows, and the like less than 2.40 meters above the pavement or groundline shall not, when fully opened or upon opening, project beyond the Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

193

property line except fire exit doors. SECTION 1008. Corner Buildings with Chaflans. —

Copyright 2010

1.

Every corner building or solid fence on a public street or alley less than 3.60 meters in width shall be truncated at the corner. The face of the triangle so formed shall be at right angle to the bisector of the angle of the intersection of the street lines, provided, that in no case shall the length of the chaflan be less than 4.00 meters. (Fig. X.3.)

2.

Corner buildings or solid wall fences to be built abutting property lines on corners of public alley or street intersections shall be provided with chaflans to afford a clear view.

3.

If the building is arcaded, no chaflan is required notwithstanding that the width of the public street or alley is less than 3.60 meters. (Fig. X.4.)

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

194

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

195

Chaflans RULE XI Protection of Pedestrians During Construction or Demolition SECTION 1101. General Requirements. — 1.

No person shall use or occupy a street, alley or public sidewalk for the performance or work covered by a building permit except in accordance with the provisions of this Rule.

2.

No person shall perform any work or any building/structure adjacent to a public way in general use for pedestrian travel, unless the pedestrians are protected as specified in this Rule.

3.

Any material, building/structure temporarily occupying public property, including fence, canopies and walkways, shall be adequately lighted between sunset and sunrise.

SECTION 1102. Storage in Public Property. — 1.

Materials and equipment necessary for work to be done under a permit when placed or stored on public property shall not obstruct free and convenient approach to and use of any fire hydrant, fire or police alarm box, utility box, catch basin, or manhole and shall not interfere with any drainage of any street or alley, gutter, and with the safe and smooth flow of vehicular and pedestrian traffic.

2.

Materials to be stored at or near construction sites shall be piled or stacked in an orderly manner to avoid toppling over or being otherwise displaced. No materials shall be piled or stacked higher than 1.80 meters, except in yards or sheds intended especially for storage. When piles exceed 1.20 meters in height, the material shall be so arranged that the sides and ends of the piles taper back. cAaDCE

SECTION 1103. Mixing Mortar on Public Property. — The mixing of mortar, concrete, or similar materials on public streets shall not be allowed. Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

196

SECTION 1104. Protection of Utilities. — 1.

All public or private utilities and services above or below the ground shall be protected from any damage by any work being done under the permit.

2.

The protection shall be maintained while such work is being done any shall not obstruct the normal functioning of any such utility.

3.

Temporary Light and Power a.

Temporary wiring for light, heat and/or power shall be adequately protected against mechanical or over-current failures. All conductive materials enclosing fixed or portable electric equipment, or forming a part of such equipment, shall be properly grounded.

b.

Temporary electric service poles shall be self-supporting or adequately braced or guyed at all times.

SECTION 1105. Walkway. —

Copyright 2010

1.

When the Building Official authorizes a sidewalk to be fenced or close, or in case there is no sidewalk in front of the building/structure site during construction or demolition, a temporary walkway of not less than 1.20 meters shall be provided.

2.

Such walkway shall be capable of supporting a uniform live load of 650.00 kilogram per sq. meters.

3.

Durable wearing surface shall be provided and must remain safe throughout the construction period.

4.

Where the sidewalk is permitted by the Building Official to be fully occupied and fenced-off or enclosed, a temporary walkway adjacent to the curb line shall be required. Where the street has no sidewalk, a temporary walkway adjacent to the street line not less than 600 millimeters wide shall be provided. Were the RROW is 5.00 meters or less, no temporary walkway shall be allowed.

5.

Where only partial occupancy and fencing-off of the sidewalk is

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

197

necessary, a temporary walkway will not be required provided that a width of at least 600 millimeters of the sidewalk with protective railing on road side shall be left open for the use of pedestrians. SECTION 1106. Pedestrian Protection. — 1.

Where the walkway occupies part of the roadway or is adjacent to an excavation, protective railings on the street side or on the side of the excavation shall be required.

2.

Railings where required, shall be built substantially strong and sturdy and shall not be less than 1.00 meters in height.

3.

Fences Fences shall entirely enclose the construction/demolition site and shall be erected on the building side of sidewalks or walkways and shall be made of approved materials (e.g. G.I. sheet, wooden boards and/or planks, plywood or Lawanit, sawali), not less than 2.40 meters in height above the curb line. Fences shall be built solid for its full length except for such openings as may be necessary for proper execution of the work. Such openings shall be provided with doors, which shall be kept closed at all times except when in actual use.

4.

a.

When the horizontal distance between the outermost face of the building/structure area and the inner edge of the sidewalk is more than one-half (1/2) the height of the building, a 2.40 meters fence is required. (Figure XI.1.)

b.

When the horizontal distance between the outermost face of the building and the inner edge of the sidewalk is equal to or less than one-half (1/2) the height of the building, a canopy shall be required in addition to a fence. (Fig. X1.2.)

Canopies a.

Copyright 2010

The protective canopy shall have a clear unobstructed height of 2.40 meters above the walkway and shall be made of sufficient strength and stability to sustain safely the weight of materials that may be placed thereon, and to withstand shocks incident to the handling of such materials or their preparation for use, and accidental jars

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

198

from trucks passing or delivering materials.

Copyright 2010

b.

When the canopy is used for the storage of materials or for the performance of work of any kind, substantial railings not less than 1.00 meters high and solid toe boards not less than 300 millimeters high shall be placed along the street side and ends of the canopy. The canopy shall be capable of safely sustaining a load of 4800 Pascal or the intended load to be placed thereon, whichever is bigger.

c.

The deck flooring of a canopy shall consist of planking not less than 50 millimeters in thickness, closely laid. All members of the canopy shall be adequately braced and connected to resist displacement of members or distortion of the framework.

d.

Canopies shall be constructed solid for its entire length except for such openings as may be necessary for loading purposes. Such openings shall be kept closed at all times except during actual loading operation.

e.

Unless the top deck of the canopy is built solidly against the face of the building/structure to be constructed/demolished, the vertical face of the canopy supports next to the building shall be solidly fenced throughout, except for such openings as may be necessary for the execution of work. Such openings shall be provided with sliding or swinging gates which shall be kept closed at all times except when in actual use. (Figs. XI.3., XI.4., XI.5., XI.6.).

f.

The street side of the canopy shall be kept open for a height of not less than 2.40 meters above the curb. The underside of the canopy shall be properly lighted at night with not less than 100-Watts bulb every 6.00 meters of its length and at each change of grade or elevation of the sidewalk surface.

g.

When a wall of the building abuts or fronts a street, fans or catch platforms shall be erected along that wall at the level of the first floor of the building above the street level. Fans or catch platforms shall be erected at the

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

199

level of other floors of the building as may be necessary to prevent nuisance from dust or danger from falling debris or materials. TAHIED

5.

Copyright 2010

h.

When the horizontal distance between the outermost face of the building and the outer edge of the sidewalk is less than one-half (1/2) the height of the building, a protective device such as a net or screen extending from the uppermost part of the construction/demolition to ground level shall be required in addition to a fence and canopy. (Fig. XI.7.)

i.

Wherever required, protective netting/covering shall be of approval and substantially strong material such as 2 millimeters diameter G.I. (illegible portion), 38 millimeters mesh nylon net, or canvas.

j.

Where a wall of the building abuts or fronts a street, dust screens all be erected to cover the entire wall so as to prevent nuisance from dust.

k.

For medium and high-rise buildings six (6) storeys and higher, all protective and safety devices/facilities shall be completely installed including safety belts, safety nets and canopies for the safety of workers, pedestrians, nearby residents and motorists.

Warning Signs and Lights a.

At every construction/demolition site, warning signs shall be conspicuously posted around the property. Warning signs shall be adequately illuminated at night for the protection of unwary pedestrians.

b.

All entrances/exits to and from the construction/demolition site shall be kept closed at all times except during actual passage of men, materials or equipment.

c.

All warning signs and lights shall be properly maintained even when operations are not in progress.

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

200

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

201

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

202

Protection of Pedestrians, Nearby Residents and the Public During Construction and Demolition d.

All areas of danger in demolition operations shall be properly enclosed and danger signs posted. Watchmen shall be provided to warn workers of impending dangers and all unauthorized persons shall be excluded from places where demolition is in progress.

SECTION 1107. Maintenance and Removal of Protective Devices. — 1.

Maintenance. All protective devices shall be properly maintained in place kept in good order for the entire length of time pedestrians may be endangered. a.

Average Light Intensity and Illumination i.

Copyright 2010

CD Technologies Asia, Inc.

All

parts

Philippine Laws Premium Edition 2009

of

buildings/structures

under 203

construction/demolition, and all sheds, scaffolds, canopied walkways, work or storage areas, and equipment used in connection with such operations shall have sufficient light to insure safety and protection of life and property. In passageways, stairways and corridors, the average light intensity measured at floor level shall be not less than 200 LUX, ii. At locations where tools and/or machinery are used, the average light intensity measured at floor level shall be not less than 500 LUX. Natural or artificial illumination shall be provided In such a manner that glare and shadows will not adversely affect the safety and protection of the public, workers and property. b.

Welding and Cutting i. Gas welding and cutting and arc welding in construction/demolition operations shall be restricted to experienced workers accredited by the Technical Education Skills Development Authority (TESDA). Suitable goggles, helmets and gloves shall be provided for and worn by workers engaged in gas welding or cutting or arc welding. Incombustible shields shall be provided to protect the workers when exposed to falling hot metal oxide. ii. Gas welding or cutting or arc welding shall not be done above pedestrians and workers. When unavoidable, an incombustible shield shall be provided between the work and workers below. A watchman shall be stationed to give warning at places where pedestrians and workers, in the course of their activity, are likely to pass under a gas welding or cutting or an arc welding operation. iii. Gas welding or cutting shall not be carried out in any place where ample ventilation is not provided or from which quick escape is difficult. When unavoidable, workers engaged in such work in confined spaces shall be allowed frequent access to fresh air. A relief worker shall be stationed close at hand to assist the worker in case of accident and to shut off the gases.

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

204

iv. Tanks of fuel gas shall not be moved or allowed to stand for any extended period when not in use unless the caps of such tanks are in place. v. Suitable cradles shall be used for lifting or lowering oxygen or fuel tanks, to reduce to a minimum the possibility of dropping tanks. Ordinary rope slings shall not be used. vi. Tanks supplying gases for welding or cutting shall be located at no greater distance from the work than is necessary for safety. vii. Such tanks shall be securely fastened in place and in upright position. They shall be stored or set in place for use so that they are not exposed to the direct rays of the sun or to high temperature. viii. Before steel beams or other structural shapes or elements of construction are cut by means of a gas flame, they shall be secured by cables or chains to prevent them from dropping or swinging. ix. Where, in the course of demolition work, steel work or ironwork is being cut, released or dismantled, all necessary precautions shall be taken to prevent danger from sudden twist, spring or collapse. c.

Special Typhoon Precautions i. Whenever a typhoon is expected to pass at or near the construction site, all construction materials and equipment shall be secured against displacement by wind forces. ii. Construction sheds, construction materials and equipment shall be secured by guying, shoring, or by tying down. iii. Where a full complement of personnel is employed or engaged for such protection purposes, normal construction activity or uses of materials or equipment may continue, allowing such reasonable time as may be

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

205

necessary to secure such materials and equipment before winds of gale force are anticipated, in accordance with warnings or advisories issued by the Philippine Atmospherical Geophysical Astronomical Services Administration (PAGASA). TCaADS

d.

Hoisting Machinery i. Every hoisting engine shall be provided with adequate brakes capable of holding the maximum load at any point of travel. ii. Hoisting machinery shall be enclosed to exclude unauthorized persons. If placed outside the building, further protection against falling objects shall be provided. iv. Guards shall be provided with exposed gears and other moving parts and around hoisting cables at all points to prevent workers from tripping or getting their clothing caught. v. Ample room shall be provided around hoisting engines, motors or machineries or apparatus to allow the free and safe movement of the operators. vi. When hoisting machinery is set on an elevated platform, such platform shall be of substantial and sturdy construction. Guardrails and toe boards shall be provided along all open sides of such platform. vii. Electrical machinery and equipment to be used for construction work shall be installed and operated in accordance with the Philippine Electrical Code. viii. Steam boilers used in construction work shall be installed, equipped and maintained in accordance with the Philippine Mechanical Code. ix. A tag line or guide rope shall be used on all loads being hoisted or lowered.

e. Copyright 2010

Platform Hoists

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

206

i. Platform hoists for the handling of materials in buildings under construction shall have the car substantially constructed and provided with covers, either solid or wire mesh. ii. If suitable overhead protection is provided, the covers may be omitted. iii. Hoists shall be equipped with a broken-rope safety device. iv. Where wheelbarrows or buggies are used for handling material on platform hoists, cleats shall be nailed to the platform to fix the proper position so that handles shall not project beyond platform edges. v. Supports for the overhead sheave of the hoist shall be designed to carry two (2) times the weight of the hoist and its maximum load. f.

Hoist Towers i. Hoist towers erected in connection with construction work shall be substantially constructed. All members shall be so proportioned that the stresses shall not exceed those specified for the material when carrying the dead load of the tower plus two times the weight of the platform or bucket or its maximum load. ii. Every hoist tower shall rest on a sufficiently solid foundation to prevent injurious settlement or distortion of its framework. iii. The base of every hoist tower shall be screened or otherwise protected on all sides to a height of not less than 1.80 meters. iv. Every hoist tower shall be secured in not less than four (4) directions against swaying or tipping at intervals of not more than 10.00 meters in its height, by steel cable guys adequately anchored or by other satisfactory means. v. Such towers which are constructed adjacent to buildings shall be secured to the building frame at each

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

207

floor as the construction progresses.

EacHSA

vi. Hoist, towers erected within the building, but not occupying the entire opening through which they pass, shall be completely enclosed on all sides and shall be provided with doors at the unloading points unless the platform hoist is solidly enclosed on all sides to the height to which material is to be loaded or unloaded. vii. Landing platforms in hoist towers or platforms connecting a hoist tower to a building or other structure shall be provided with guardrails and toe boards. g.

Derricks and Cranes i. Derricks shall be so designed and assembled that no part shall be stressed beyond the safe working stress for the material under its maximum rated load in any possible position. Such maximum load shall be conspicuously posted on each derrick. ii. The foot-block of every derrick shall be firmly secured against motion in any direction. iii. Guy derricks shall have the top of the mast held by not less than six (6) steel guy cables secured by firm anchorages and so placed that the angle of the guy with the mast shall be as large as possible. iv. The moving parts of derricks and cranes shall be kept well lubricated. All parts shall be inspected at least every other day. v. Use and operation of cranes shall be in accordance with Rule XIII. vi. In the operation of cranes and similar devices, a standard signal system shall be used and all men assigned to the operation of such equipment shall be fully instructed on the signals.

h.

Cables, Ropes, Chains and Blocks i.

Copyright 2010

CD Technologies Asia, Inc.

All ropes and cables used in connection with

Philippine Laws Premium Edition 2009

208

scaffolds, derricks and hoisting apparatus shall be tested before being put to use and at least once every thirty (30) days while in use, to insure their safety and suitability for the purpose. ii. Cables, ropes, chains and blocks shall be of such size that the maximum load supported by them will not exceed one-sixth (1/6) of their breaking strength. iii. Blocks designed for use with abaca ropes shall not be used for steel cables. iv. Blocks used at or near floors or in other exposed places to change the direction of cables shall be enclosed or otherwise effectively guarded. v. Chains shall not be used for slings, bridles or other similar purposes, but shall be restricted to only a straight pull. vi. Hooks shall not be used for hoisting buckets, cages or skips. i.

Ladders and Temporary Stairways i. Except where either permanent or temporary stairways or runways are required, ladders shall be provided to give access to all floors, stagings or platforms where work is being done more than five (5) storeys above ground or above a permanent or temporary floor. ii. Ladders shall not be extended by joining two (2) or more together. No single ladder shall exceed 6.00 meters in length. When greater heights are to be reached, intermediate platforms shall be erected. iii. Ladder landings shall be at least 1.20 meters square and equipped with handrails and toe boards. iv. Ladder rungs shall be spaced uniformly and as near to 300 millimeters as practicable. v.

Copyright 2010

CD Technologies Asia, Inc.

Ladders leading to floors, stagings or platforms

Philippine Laws Premium Edition 2009

209

shall extend at least 900 millimeters above the level of such floors, stagings or platforms. vi. When used temporarily in place of stairways or runways, ladders serving traffic in both directions simultaneously shall be at least 1.00 meters wide. If separate ladders are provided for going up and coming down, they shall be marked "UP" and "DOWN" respectively at each floor and platform level. vii. All ladders, when in use, shall be set up in a manner to be secured and to prevent slipping. Ladders, except stepladders or other self-supporting ladders, shall be securely fastened to a permanent support at the top, and if necessary, at the bottom, and braced to prevent swaying, bending or shaking. viii. Ladders shall not be placed or used in shafts of operative elevators or hoists except by workers engaged in the erection, construction, alteration or repair of any such shafts, hoistways or equipment. ix. Ladders shall not be painted, but may be oiled or treated with preservatives so as to permit the detection of faults. x. Every ladder shall be inspected by the superintendent or foreman in charge before being put to use on a construction operation and thereafter at least once every thirty (30) days while in continued use. xi. Permanent stairways shall be installed in all buildings under construction as soon as conditions will permit. xii. When the work on a building has progressed to a height in excess of 18.00 meters and it has not been practicable to install the permanent stairways, at least one temporary stairway shall be provided for the full height and continued upward as rapidly as the work progresses. xiii. Stairs and stairways shall be of sufficient strength Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

210

to support a load of at least 4800 Pascal. All stairways shall be guarded on all open sides with handrails and toe boards. xiv. Temporary stairs shall be constructed so that treads and risers are uniform in width and height in any one (1) flight. xv. The sum of the height of the two (2) risers and the width of one (1) tread shall be not less than 460 millimeters nor more than 700 millimeters. xvi. Temporary stairways shall be not less than 900.00 millimeters wide. xvii. Landings shall be not less than 750 millimeters long. No flight of stairs of temporary stairways shall have a vertical rise in excess of 3.60 meters. Whenever necessary, intermediate landings shall be provided. xviii. Temporary and permanent stairways shall be adequately lighted. xix. Permanent stairs that are to be used during construction and on which treads are to be filled in later shall have wooden treads firmly fitted in place for the full area of the tread. xx. The top surfaces of the temporary treads shall be maintained above the tops of the risers or nosings. xxi. No door shall open directly onto a flight of stairs, but a landing equal at least the width of the door shall be provided between the door and the stairs. j.

Runways and Ramps i. Runways and ramps used in connection with scaffolds or extending from storey to storey or otherwise located and maintained for an extended period of time or for the transfer of bulky material shall be constructed of at least three (3) 25 x 250 millimeters planks laid closely side by side and substantially supported and braced to prevent unequal deflection and springing action.

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

211

ii. Runways and ramps shall have a slope not greater than one is to three (1:3). The total rise of a runway or ramp between landings shall not exceed 1.80 meters. iii. When the rise is steeper than 1:3, runways or ramps shall be provided with cleats spaced not more than 20 millimeters apart. iv. Runways and ramps having a total rise of more than 1.80 meters, or passing over or near floor openings, high tension wires or other dangerous places, shall be provided with guardrails and toe boards. ACcTDS

h.

Scaffolds i. Properly constructed scaffolds shall be provided for all works which cannot be done safely by workmen standing on permanent or solid construction, except when such work can be done safely from ladders. All such scaffolds shall be substantially constructed to support at least four (4) times the maximum load, and shall be secured to prevent swaying. ii. Planks used in the construction of stationary scaffolds shall be not less than 50 millimeters nominal thickness. Where such planks overlap at the ends, the overlap shall be not less than 150 millimeters. Planks shall be so placed that they cannot tip under the weight of the worker at any point. All nails shall be driven full strength. No nails shall be subject to direct pull. iii. Ropes, cables and blocks shall sustain at least six (6) times the maximum loads to which they will be subjected. Where acids are likely to come in contact with them, ropes shall not be used but steel cables properly protected by grease or oil or other effective methods shall be used instead. iv. Every scaffold, the platform level of which is more than 1.80 meters above the ground, or above a permanent or temporary floor, other than iron workers' scaffolds and carpenters' bracket scaffolds, shall be provided with guard rails and toe boards extending the full length of the

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

212

scaffold and along the ends except where ramps or runways connect with them, unless otherwise enclosed or guarded. On suspended, swinging and pole scaffolds, the space between guardrails and toe boards shall be fitted with wire mesh screens securely attached. v. Where objects are likely to fall on a scaffold from above, a substantial overhead protection shall be provided not more than 3.00 meters above the scaffold platform, and at doorways, passageways or other points. Where workers must pass under scaffolds, a substantial overhead protection shall be provided. vi. No materials or equipment other than required by the workers shall be placed on scaffold platforms. vii. Roof brackets, roof scantling, crawling boards and similar forms of supports shall be substantial in construction and securely fastened In place when in use. viii. Barrels boxes or other similar-unstable objects shall not be used as supports. ix. When used over public sidewalks or other places of public use, scaffolds used for minor building repairs, alterations, or painting, shall be equipped with drop cloths to effectively prevent the falling of paint or debris. x. Scaffolds used for sandblasting and guniting operations shall be entirely and effectively enclosed, and the determination of effective enclosure shall be the completed absence of particles of materials of operation in the air at a horizontal distance of 15.0 meters from the point of operation. k.

Temporary Flooring i. In buildings of skeleton construction, the permanent floor, except for necessary hoistway openings, shall, when possible, be constructed as the building progresses. There shall be not more than three (3) unfilled floors below the highest permanent floor. ii.

Copyright 2010

CD Technologies Asia, Inc.

In buildings of skeleton construction, the entire

Philippine Laws Premium Edition 2009

213

working floor shall be planked over, except spaces required for raising or lowering materials, and for stairways or ladders. Planks shall not tip under the weight of a worker at any point and secured, so that they cannot slip out of place. iii. In buildings of wood joist construction, the immediate underfloor shall be laid for each floor as the building progresses. l.

Floor Openings i. All floor openings used as hoistways or elevator shaftways shall be protected on all sides, except the side being used for loading or unloading. Protection shall be in the form of barricades or guardrails not less than 900 millimeters high placed not less than 600 millimeters distant at all points from the edges of such openings. If guardrails are used, toe boards shall be provided along the edges of the openings. Sides left open for loading or unloading shall be guarded by similar solid doors or gates. DaESIC

ii. All floor openings used as stairways or for the accommodation of ladders or runways shall be guarded by railings and toe boards. iii. All floor openings shall be protected on all sides by solid barriers or railings with toe boards not less than 900 millimeters high or shall be planked over by temporary construction capable of sustaining safely such loads as are likely to come thereon. iv. Barriers for the protection of openings used as hoistways or for elevators shall be constructed so that workers cannot thrust head, arms or legs through them, and loose materials cannot fall or be pushed into the shaftway. v. Barriers and guardrails around floor openings shall remain in place until permanent enclosures or protection are otherwise provided.

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

214

m.

Guardrails and Toe Boards i. Guardrails, when required under this Rule, shall have the top rail not less than 900 millimeters with an intermediate rail provided between the top rail and the platform. ii. All guardrails shall have supports not more than 2.40 meters apart, constructed to withstand a horizontal force of 30 kilograms per sq. meters. iii. Toe boards, whenever required under this Rule, shall extend not less than 150 millimeters above the platform level and shall be placed to fit close to the edges of the platform. They shall be adequately secured along the entire length to resist the impact of workers' feet and the shifting of materials. iv. Toe boards of metal shall be not less than 25 millimeters nominal thickness, with supports not more than 1.20 meters apart. v. Toe boards of metal shall be not less than 30 millimeters thick, with supports not more than 1.20 meters apart.

2.

Removal. Every protective fence or canopy shall be removed within 30 days after such protection is no longer required as determined by the Building Official.

SECTION 1108. Demolition. —

Copyright 2010

1.

If the work is of a difficult or dangerous nature, it should be done by a contractor experienced in such work.

2.

Before demolition is commenced, notice of intention to proceed should be given to the adjoining owners of the buildings.

3.

Before commencing to demolish a building or repair a badly damaged building, shoring, tying, and strutting are necessary to prevent movement.

4.

For the purposes of arranging shores, ties, and other security measures, a survey of the existing building and the adjoining

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

215

owner's building should be made prior to demolition and, where possible, particulars of existing wall foundations and of the subsoil should be obtained. cHTCaI

Copyright 2010

5.

Demolition should be done as much as possible, floor-by-floor.

6.

Care should be taken to dispose of debris as it arises. If this is not done, there is a great risk of overloading the floors, which may result in a collapse. All debris arising from demolition should be kept damp by means of spraying water from a hose with a fine spray to prevent dust arising and causing inconvenience to adjoining owners and pedestrians.

7.

Fans or catch platforms should be provided over public footways, etc., to protect workmen and occupants of adjoining building and the general public from falling debris during demolition. One fan at the first (1st) floor level should be sufficient for buildings of three (3) storeys. Building of more than three (3) storeys should have additional fans at higher levels, generally at alternate floor levels.

8.

Precautions Before Demolition a.

Before commencing the work of demolition of a building/structure, all gas, electric, water and other utility meters shall be removed and the supply and service lines disconnected by the corresponding utility/service companies, who should be notified in advance.

b.

All fittings attached to the building/structure and connected to any street lighting system, electrical supply or other utilities shall be removed.

c.

All electric power shall be shut off and all electric service lines shall be cut and disconnected by the power company at or outside the property line.

d.

No electric cable or other apparatus, other than those especially required for use in connection with the demolition work, shall remain electrically charged during demolition operations. When it is necessary to maintain any power, water, gas, or other utility/service

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

216

lines during the process of demolition, such lines shall be temporarily relocated and protected with substantial covering to the satisfaction of the utility/service company concerned. e.

All necessary steps shall be taken to prevent danger to persons arising from fire or explosion from leakage or accumulation of gas or vapor, and from flooding from uncapped water mains, sewers and/or culverts.

f.

All entrances/exits to and from the building shall be properly protected so as to prevent any danger to persons engaged in the demolition work using such entrances/exits in the performance of their works. cTCaEA

g. 9.

Copyright 2010

Glazed sashes and glazed doors shall be removed before the start of demolition operations.

Chutes a.

Chutes for the removal of materials and debris shall be provided in all parts of demolition operations, which are more than 6.00 meters above the point from which material is to be removed. Chutes shall be so situated and constructed so as not to pose any danger to the public or to workmen.

b.

Chutes shall be completely enclosed and shall be equipped, at intervals of 6.00 meters or less, with substantial stops to prevent descending materials from attaining dangerous speeds. Proper tools shall be provided and kept available to loosen materials or debris jammed in the chute. No materials or debris shall be dropped from any part of a building under demolition to any point outside the walls of the building except through properly enclosed wooden or metal chutes.

c.

Chutes which are at an angle of more than 45o from the horizontal shall be completely enclosed on all four (4) sides, except for openings at or about floor level at each floor, for the receiving of materials or debris.

d.

Chutes at an angle of less than 45o with the horizontal

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

217

may be left open on the upper side. However, where such a chute discharges into another chute steeper than 45o with the horizontal, the top of the steeper chute shall be covered at the junction point of the two (2) chutes to prevent the spillage of materials or debris.

10. Copyright 2010

e.

Openings Into which materials or debris are dumped at the top of a chute shall be protected by a substantial guardrail extending at least 1.80 meters above the level of the floor.

f.

At chute openings where materials or debris are dumped from wheelbarrows, a toe board or bumper not less than 150 millimeters high and 50 millimeters nominal thickness shall be provided.

g.

Any space between the chute and edges of floor openings through which the chute passes shall be solidly planked over.

h.

Chutes, as well as floors, stairways and other places, shall be effectively wet down at frequent intervals, whenever the dust from demolition operations would cause a menace or hardship to residents of adjoining buildings or premises.

i.

The bottom of each chute shall be equipped with an adjustable gate or stop for regulating the flow of materials.

j.

Except when In actual use in the discharge of materials, the gate or stop shall be kept closed. A reliable person shall be designated to control the gate and the backing up and loading of trucks. He shall see to it that no person is allowed to stand or pass under the discharge end of the chute at any time.

k.

The area at the discharge end of each chute shall be completely enclosed with a substantial fence at all times or otherwise made inaccessible. A danger sign shall be placed at the discharge end of every chute.

Demolition of Walls and Chimneys

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

218

Copyright 2010

a.

No wall, chimney or other construction shall be allowed to fall in mass, except under competent supervision.

b.

Scaffolds or stagings shall be erected for workers if walls or other elements of the structure are too thin or too weak to work on. Heavy structural members, such as beams or columns, shall be carefully lowered and not allowed to fall freely.

c.

Masonry walls or sections of masonry walls shall not be permitted to fall upon the floors of the building in such masses as to exceed the safe carrying capacity of the floors.

d.

No walls or section of walls whose height is more than twenty-two (22) times its thickness shall be permitted to stand without lateral bracing unless such wall is in good condition and was originally designed to stand to a greater height without such lateral support.

e.

Workmen shall not be permitted to work on top of a wall when weather conditions constitute a hazard.

f.

Before demolishing any interior or exterior wall which is within 3.06 meters of any opening in the floor immediately below, such opening shall be substantially planked over unless all workmen are removed from all floors below and access to such floors is positively prevented.

g.

At the completion of each day's work, all walls undemolished shall be left stable and in no danger of overturning or falling.

h.

Foundation walls which serve as retaining walls to support earth and adjoining structures shall not be demolished until such adjoining structures have been underpinned or braced, and earth either removed or supported by sheet piling or other suitable materials.

i.

In the demolition of brick and/or masonry chimneys which cannot safely be toppled or dropped, all materials shall be dropped down through the inside of such

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

219

chimneys. j.

The loading point at the discharge end chute, at or near the bottom of a chimney, shall be completely protected by means of any overhead timber canopy.

k.

To enable workmen to reach or leave their work on any wall or scaffold, walkways shall be provided. Such walkways shall not be less than three (3) planks, properly tied or nailed to bearers of not less than 560 millimeters in width, such that the planks do not deflect more than 50 millimeters under normal loading.

l.

In buildings of skeleton construction, the steel framing may be left in place during the demolition of masonry work. When this is done, all steel beams, girders and the like shall be cleared of all loose materials as the demolition progresses. EHCcIT

11.

Copyright 2010

Demolition of Floors a.

Before the demolition of floors and floor beams, the floors and beams shall be completely supported by temporary planking and supports.

b.

When the load is transferred to lower floors, these floors shall be carefully propped.

c.

Demolition of floors shall not be started until the surrounding floor area to a distance of 6.00 meters have been entirely cleared of debris and other unnecessary materials.

d.

No floor, roof or other part of a building that is being demolished shall be so overloaded with debris or materials as to render it unsafe.

e.

Where workmen are engaged in the removal of floors, planks of ample strength which are supported independently of the flooring shall be provided for the workmen to step on. The planks shall be so placed as to give the workmen a firm support in case the floor gives way or collapses unexpectedly. Where it is necessary for a workman to straddle a space between two planks, such

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

220

space shall not exceed 400 millimeters. To enable workmen to reach any workplace without the necessity of walking on exposed beams, planks shall be provided to serve as catwalks.

12.

Copyright 2010

f.

Planks used for temporary protection shall be sound, and at least 25 millimeters thick. They shall be laid close together, with the ends overlapping by at least 100 millimeters over solid bearings to prevent tipping under a load.

g.

Where floors are being removed, no workmen shall be allowed to work in the area directly underneath. Such areas shall be barricaded to prevent access to it.

h.

Structural or load-supporting members at any floors shall not be cut or removed until all stories above that floor have been demolished and removed.

i.

Where any floor has been removed, the entire tier of beams on which any device Is supported shall be completely planked over, except for such openings as are required for the handling of materials or equipment.

j.

Stairs and stair railings shall be kept in place and in usable condition as long as it is practicable.

k.

Steps and landings shall be kept free from debris and obstructions.

Other Safeguards a.

Where applicable, the Building Official shall require strict compliance with the minimum safety standards as prescribed under Administrative Order of DOLE. The construction, alteration and removal of scaffolds and the application, installation and setting up of safeguard devices shall be done by skilled workmen under the supervision of a person, qualified by experience or training for such work.

b.

A device or piece of equipment, which is unsafe, shall be reported to the superintendent or foreman, who shall take immediate steps to remedy such condition or remove

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

221

such device or equipment.

Copyright 2010

c.

Scaffolds, ladders, stairs, fuel gas tanks and other devices or equipment falling within the scope of this Rule shall be maintained in a good, safe and usable conditions as long as in use.

d.

Scaffolds, temporary floors, ramps, stairway landings, stair treads, and all other walkway surfaces shall be kept free from protruding nails/splinters.

e.

Protruding nails and tie wire ends shall be removed, hammered in or bent in a safe condition.

f.

Electric lines, moving ropes and cable gears, or similar hazards with which a person might come in contact with shall be encased or protected.

g.

No person, firm or corporation, either personally or through an employee or agent of another, shall operate or move any machinery, equipment, materials, scaffolds, closer than 5.00 meters to any energized high voltage overhead electrical facilities unless authorized by the Electrical Inspector.

h.

All workmen on any demolition job shall be required to wear industrial safety helmets and body protective gears.

i.

Construction sheds and toolboxes shall be so located as to protect persons from dangerous falling walls and objects.

j.

The Building Official may permit the use of alternative methods and/or devices depending on local conditions provided that the minimum standard of safety sought to be achieved under this Rule is not jeopardized.

k.

In Fire Zones of Types I, II and III Construction, only heaters with enclosed flames shall be used for the heating of any roofing or other similar materials.

l.

Wherever any enclosed flame heaters or open fires are used, there shall be a workman in constant attendance, whose duty shall be to have such heater or fire under

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

222

proper control at all times. m.

In all buildings in which standpipes are required, such standpipes shall be installed as the construction progresses in such a manner that they are always ready for Fire Department use, to the topmost constructed floor. Such standpipes shall be provided with a Siamese twin dry standpipe outside the building and with one (1) outlet at each floor connected to a fire hose cabinet.

n.

In every construction operation, wherever a tool house, storeroom or other shanty is built or a room or space is used for storage, dressing room or workshop, at least one (1) approved hand pump, tank or portable chemical or dry powder fire extinguisher shall be provided and maintained in an accessible location.

o.

During construction operations, free access from the street to fire hydrants and to outside connections for standpipes, sprinklers or other fire extinguishing equipment, whether permanent or temporary shall be provided and maintained at all times. No material or construction equipment shall be placed within 3.00 meters of such hydrant or connection, nor between it and the centerline of the street. ADCETI

Copyright 2010

p.

Toilet facilities at the construction/demolition site, as an ancillary to the bunkhouse and operation, shall be maintained in a clean/sanitary condition for the use of the workers.

q.

Supply of potable water and sanitary washing facilities shall be provided for workers' and other uses during workdays.

r.

At every construction/demolition operation, arrangements shall be made for prompt medical attention in case of an accident. An ample supply of first aid medicine shall be provided and maintained in a clean/sanitary cabinet, which shall be available at all times under the direction of the superintendent or a person designated by him.

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

223

s.

Unless competent medical attention is quickly available, where more than two hundred (200) workers are employed, a properly equipped first-aid room shall be provided, and a physician or competent nurse shall be in constant attendance. RULE XII General Design and Construction Requirements

SECTION 1201. General Requirements. —

Copyright 2010

1.

Buildings proposed for construction shall comply with all the regulations and specifications including safety standards embodied in the Administrative Order of DOLE herein set forth governing quality, characteristics and properties of materials, methods of design and construction, type of occupancy and classification.

2.

The various applicable referral codes shall supplementally guide the planning, design, layout, content, construction, location/siting, installation and maintenance of all buildings/structures.

3.

For the guidance of the general public, the Secretary shall periodically issue generic lists of approved, strictly regulated or banned items, procedures, usages and the like relative to the design, construction and use/occupancy of buildings/structures: a.

Materials for construction;

b.

Processes for the production of materials, their installation or construction;

c.

Procedures/methodologies/systems for both design and construction;

d.

Organizational structures/hierarchies for construction;

e.

Types of occupancy; and

f.

Classifications relative to design, construction and occupancy.

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

224

4.

All buildings/structures shall be placed in or upon private property or duly designated public land and shall be securely constructed in conformance with the requirements of the Code.

SECTION 1202. Excavation, Foundation, and Retaining Walls. — 1.

Subject to the provisions of Articles 684 to 686 of the Civil Code of the Philippines on lateral and subjacent support, the design and quality of materials used structurally in excavation, footings, and in foundations shall conform to accepted engineering practice. IcTaAH

2.

Excavation and Fills a.

Excavation and fills for buildings or structures shall be so constructed or protected that they do not endanger life or property.

b.

Whenever the depth of excavation for any construction is such that the lateral and subjacent support of the adjoining property or existing structure thereon would be affected in a manner that the stability or safety of the same is endangered, the person undertaking or causing the excavation to be undertaken shall be responsible for the expense of underpinning or extending the foundation or footings of the aforementioned property or structure.

c.

Excavation and other similar disturbances made on public property shall, unless otherwise excluded by the Building Official, be restored immediately to its former condition within 48 hours from the start of such excavation and disturbances by whosoever caused such excavation or disturbance.

d.

Before undertaking excavation works, drilling or otherwise disturbing the ground, the persons doing the work, or causing such work to be done, shall contact all public utilities/services to determine the possible location of underground facilities, to avoid hazard to public safety, health and welfare caused by the inadvertent disruption of such facilities. e.

Copyright 2010

CD Technologies Asia, Inc.

Protection of Adjoining Property. Any person making or Philippine Laws Premium Edition 2009

225

causing an excavation to be made below existing grade shall protect the excavation so that the soil of adjoining property will not cave-in or settle and shall defray the cost of underpinning or extending the foundation of buildings on adjoining properties. Before commencing the excavation, the person making or causing the excavation to be made shall notify in writing the owners of adjoining buildings not less than ten (10) days before such excavation is to be made and that the adjoining buildings will be protected by him. The owners of the adjoining properties shall be given access to the excavation for the purpose of verifying if their properties are sufficiently protected by the person making the excavation. Likewise, the person causing such excavation shall be given access to enter the adjoining property for the purpose of physical examination of such property, prior to the commencement and at reasonable periods during the progress of excavation. If the necessary consent is not accorded to the person making the excavation, then it shall be the duty of the person refusing such permission to protect his buildings or structure. The person causing the excavation shall not be responsible for damages on account of such refusal by the adjoining property owner to permit access for inspection. In case there is a party wall along a lot line of the premises where an excavation is being made, the person causing the excavation to be made shall at his own expense, preserve such party wall in as safe a condition as it was before the excavation was commenced and shall, when necessary, underpin and support the same by adequate methods.

Copyright 2010

f.

At an early stage, and before work is commenced, a careful and accurate survey of any cracks in the existing adjoining owner's premises should be made, and, where possible, photographs should be taken, recorded, and agreed between the parties concerned. Where necessary, tell-tales should be fixed to cracks with the object of showing any further movements, during demolition and excavation. Tell-tales should preferably be in the form of fixed points built in on each side of the crack and should be capable of being measured by a micrometer or vernier caliper. They should be of such a nature that both horizontal and vertical movements could be recorded.

g.

Cut slopes for permanent excavations shall not be

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

226

steeper than two (2) horizontal to one (1) vertical and slopes for permanent fills shall not be steeper than two (2) horizontal to one (1) vertical. Deviation from the foregoing limitations for slopes shall be permitted only upon the presentation of a geotechnical/geological investigation report acceptable to the Building Official.

Copyright 2010

h.

On a large site that is at a considerable distance from the surrounding properties and public highways, deep excavation may be carried out in the open in bulk, leaving slopes around the perimeter. It is important to ensure that no serious failures of the banks will occur to endanger those working on the site or the public. The safe angle of the cut slope shall be determined by an appropriate geotechnical/geological site investigation acceptable to the Building Official.

i.

In cases where the excavation passes through a permeable water-bearing stratum overlying an impervious bed, a bench should be formed at the junction of the strata to carry an intermediate intercepting drain.

j.

If groundwater is standing at a considerable head around the excavation, measures shall be undertaken to reduce this head by a system of weepholes at the lowest 1/3 section of the excavation wall or by enclosing the site with suitable sheet piling or if a water-sealing stratum can be reached within a reasonable distance at the bottom of the excavation.

k.

In fine sands or silts where sheet piling alone is relied upon, it will be necessary to watch the pumping very carefully because, in fine-grained materials, the removal of even a small volume of water may cause "blows" in the bottom of the excavation or may result in disturbance to adjoining structures.

l.

Except in excavation inside sloping banks, rock, or within caissons, all excavations should be lined with shotcrete, boards, runners or sheet piles supported laterally, if necessary, by framings of wallings and struts, which may be of timber, steel, or reinforced concrete, to

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

227

a sufficient extent to prevent the excavation from becoming dangerous to life or limb by movement or caving in of the adjoining soil. IcESDA

Copyright 2010

m.

All linings and framings should be inserted as the excavation proceeds, and should be tightened up against the adjoining soil by wedging or jacking and secured by cleats or other suitable means.

n.

Every trench, 1.50 meters or deeper, shall be provided with suitable means of exit or escape at least every 7.50 meters of its length.

o.

Where workers are employed adjacent to an excavation on work other than that directly connected with the excavation, sufficient railings or fences shall be provided to prevent such workers from falling into the excavation.

p.

Excavations that may be left open for any length of time, periodic inspections of timbering or strutting should be made and wedges tightened as found necessary.

q.

In long excavation for walls, it may be found expedient and safe to arrange the excavation in a series of alternate sections in order to avoid a long, continuous excavation supported only on temporary strutting. Such sections should be arranged in convenient lengths (depending on the total length to be done) and of a width sufficient to construct a unit of the retaining wall that will be adequate to afford permanent support to that portion of the ground; the wall unit should be completed before proceeding with the adjacent section of the excavation.

r.

Where water is encountered in excavation, a sump should be maintained below the level of the excavation in order that surface and groundwater can be led into it and pumped out; provided that the inflow of water does not carry much soil in suspension and does not require continuous pumping to keep the risk of settlement of the surrounding ground.

s.

No fill or other surcharge loads shall be placed adjacent to any building/structure unless such building/structure is

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

228

capable of withstanding the additional loads caused by the fill or surcharge.

3.

t.

Existing footings or foundations which may be affected by any excavation shall be underpinned adequately, or otherwise protected against settlement, and shall be protected against lateral movement.

u.

Fills to be used to support the foundations of any building/structure shall be placed in accordance with accepted engineering practice. A soil investigation report, and a report of satisfactory placement of fill, shall be both acceptable to the Building Official.

Footings, Foundations, and Retaining Walls a.

Footings and foundations shall be of the appropriate type, of adequate size, and capacity in order to safely sustain the superimposed loads under seismic or any condition of external forces that may affect the safety or stability of the structure. It shall be the responsibility of the architect and/or engineer to adopt the type and design of the same in accordance with the standards set forth by the Secretary. DCASEc

b.

Whenever or wherever there exist in the site of the construction an abrupt change in the ground levels or level of the foundation such that instability of the soil could result, retaining walls shall be provided and such shall be of adequate design and type of construction as prescribed by the Secretary.

SECTION 1203. Veneer. —

Copyright 2010

1.

Veneer is a non-structural facing of brick, concrete, tile, metal, plastic, glass, or other similar approved materials attached to a backing or structural components of the building for the purpose of ornamentation, protection, or enclosure that may be adhered, integrated, or anchored either on the interior or exterior of the building or structure.

2.

Design Requirements. The design of all veneer shall comply with the following:

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

229

a.

Veneer shall support no load other than its own weight and the vertical dead load of veneer immediately above.

b.

Surfaces to which veneer is attached shall be designed to support the additional vertical and lateral loads imposed by the veneer.

c.

Consideration shall be given to differential movements of the supports including those caused by temperature changes, shrinkage, creep, and deflection.

d.

Adhered veneer and its backing shall be designed to have a bond to the supporting elements sufficient to withstand shearing stresses due to their weights including seismic effects on the total assemblage. aHICDc

e.

Anchored veneer and its attachment shall be designed to resist horizontal forces equal to twice the weight of the veneer.

f.

Anchors, supports and ties shall be non-combustible and corrosion-resistant.

SECTION 1204. Enclosure of Vertical Openings. —

Copyright 2010

1.

General. Vertical openings shall be enclosed depending upon the fire resistive requirements of a particular type of construction as set forth in the Code.

2.

Elevator Enclosures. Walls and partitions enclosing elevators and escalators shall be of not less than the fire-resistive construction required under the Types of Construction. Enclosing walls of elevator shafts may consist of wire glass set in metal frames on the entrance side only. Elevator shafts extending through more than two storeys shall be equipped with an approved means of adequate ventilation to and through the main roof of the building; Provided, that in those buildings housing Groups F and G Occupancies equipped with automatic fire-extinguishing systems throughout, enclosures shall not be required for escalators; Provided, further that the top of the escalator opening at each storey shall be provided with a draft curtain. Such draft curtain shall enclose the perimeter of the unenclosed opening and shall extend from the ceiling

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

230

downward at least 300 millimeters on all sides. Automatic sprinklers shall be provided around the perimeter of the opening and within a 600 millimeters of the draft curtain. The distance between the sprinkles shall not exceed 1.80 meters center-to-center. 3.

Other Vertical Openings. All shafts, ducts, chutes, and other vertical openings not covered in paragraph above shall have enclosing walls conforming to the requirements specified under the type of construction of the building in which they are located. In other than Group A Occupancies, rubbish and linen chutes shall terminate in rooms separated from the remainder of the building by a One-Hour Fire-Resistive Occupancy Separation. Openings into the chutes shall not be located in required exit corridors or stairways. AHcDEI

4.

Air Ducts. Air ducts passing through a floor shall be enclosed in a shaft. The shaft shall be as required in this Code for vertical openings. Dampers shall be installed where ducts pierce the shaft enclosure walls. Air ducts in Group A Occupancies need not be enclosed in a shaft if conforming to the mechanical provisions of the Code.

SECTION 1205. Floor Construction. — 1.

Floors shall be of such materials and construction as specified under Rule V — Fire Zones and Fire-Resistive Standards and under Rule IV — Types of Construction.

2.

All floors shall be so framed and secured into the framework and supporting walls as to form an integral part of the whole building.

3.

The types of floor construction used shall provide means to keep the beam and girders from lateral buckling.

SECTION 1208. Roof Construction and Covering. — 1.

Copyright 2010

Roof Covering. Roof covering for all buildings shall be either fire-retardant or ordinary depending upon the fire-resistive requirements of the particular type of construction. The use of combustible roof insulation shall be permitted in all types of construction provided it is covered with approved roof covering

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

231

applied directly thereto. 2.

Roof Trusses. All roofs shall be so framed and tied into the framework and supporting walls so as to form an integral part of the whole building. Roof trusses shall have all joints well fitted and shall have all tension members well tightened before any load is placed in the truss. Diagonal and sway bracing shall be used to brace all roof trusses. The allowable working stresses of materials in trusses shall conform to the Code. Camber shall be provided to prevent sagging. llcd

3.

Attics. a.

Access. An attic access opening shall be provided in the ceiling of the top floor of buildings with a combustible ceiling or roof construction. The opening shall be located in a corridor or hallway of buildings of three (3) or more storeys in height and readily accessible in buildings of any height. An opening shall not be less than 600 millimeters square or 600 millimeters in diameter. The minimum clear headroom of 800 millimeters shall be provided above the access opening. For ladder requirements, refer to the Philippine Mechanical Engineering Code.

b.

Area Separation. Enclosed attic spaces of combustible construction shall be divided into horizontal areas not exceeding 250 sq. meters by fire-resistive partitions extending from the ceiling to the roof, Except, that where the entire attic is equipped with approved automatic fire extinguishing system, the attic space may be divided into areas not to exceed 750 sq. meters. Openings in the partitions shall be protected by self-closing doors. CcaASE

Copyright 2010

c.

Draft Stops. Regardless of the type of construction, draft stops shall be installed in trusses roofs, between roof and bottom chords or trusses, in all buildings exceeding 2000 sq. meters. Draft stops shall be constructed as for attic area separations.

d.

Ventilation. Enclosed attics including rafter spaces formed where ceilings are applied direct to the underside

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

232

or roof rafters shall be provided with adequate ventilation protected against the entrance of rain. 4.

5.

Roof Drainage System a.

Roof Drains. Roof drains shall be installed at low points of the roof and shall be adequate in size to discharge all tributary waters.

b.

Overflow Drains and Scuppers. Where roof drains are required, adequate overflow drains shall be provided.

c.

Concealed Piping. Roof drains and overflows drains, when concealed within the construction of the building, shall be installed in accordance with the provisions of the National Plumbing Code.

d.

Over Public Property. Roof drainage water from a building shall not be permitted to flow over public property, except for Group A and J Occupancies.

Flashing. Flashing and counter-flashing shall be provided at the juncture of the-roof and vertical surfaces.

SECTION 1207. Stairs, Exits, and Occupant Loads. — 1.

General. The construction of stairs and exits shall conform to the occupant load requirements of buildings, reviewing stands, bleachers, and grandstands. a.

Determination of Occupant Loads. The occupant load permitted in any building or portion thereof shall be determined by dividing the floor area assigned to that use by the unit area allowed per occupant as shown on Table XII.1. and as determined by the Secretary. i. When the unit area per occupant for any particular occupancy is not provided for in Table XII.1., the Building Official shall determine the same based on the unit area for occupancy, which it most nearly resembles, ii. The occupant load of any area having fixed seats shall be determined by the number of fixed seats installed. Aisles serving the fixed seats in said area shall

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

233

be included in determining the occupant load. iii. The occupant load permitted in a building or portion thereof may be increased above that specified in Table XIII.1. If the necessary exits are provided. iv. In determining the occupant load, all portions of a building shall be presumed to be occupied at the same time. EXCEPTION: Accessory areas, which ordinarily are only used by persons who occupy the main areas of occupancy, shall be provided with exits as though they were completely occupied. However, in computing the maximum allowable occupant load for the floor/building, the occupant load of the accessory area/s shall be disregarded. HDcaAI

b.

Exit Requirements. Exist requirements of a building or portion thereof used for different purposes shall be determined by the occupant load which gives the largest number of persons. No obstruction shall be placed in the required width of an exit except projections permitted by the Code.

c.

Posting of Room Capacity. Any room having an occupant load of more than fifty (50) where fixed seats are not installed, and which is used for classroom, assembly, or similar purpose shall have the capacity of the room posted in a conspicuous place near the main exit from the room.

d.

Changes in Elevation. Except in Group A Occupancies, changes in floor elevations of less than 300 millimeters along any exit serving a tributary occupant load of ten (10) or more shall be by means of ramp. Table XII.1. General Requirements for Occupant Loads and Exits*

(*In all occupancies, floors above the first (1st) storey having an occupant load of more than ten (10) shall have at least two (2) exits) Use or Occupancy Copyright 2010

CD Technologies Asia, Inc.

Unit Area per Philippine Laws Premium Edition 2009

Minimum of Two (2) Exits 234

Occupant (sq. meters) Dwellings Hotels Apartments Dormitories Classrooms Conference Rooms Exhibit Rooms Gymnasia School Shops Vocational Institutions Laboratories Hospitals**, Sanitaria** Nursing Homes** Children's Homes** Homes for the Aged** (**Institutional Sleeping Departments shall be based on one (1) occupant per 11.00 sq. meters of the gross floor area; In-patient Institutional Treatment Departments shall be based on one (1) occupant per 22.00 sq. meters of gross floor area) Nurseries for Children Dwellings Stores-Retail Sales Rooms Basement Ground Floor Upper Floors Offices Aircraft Hangars (no repair) Parking Garages Drinking Establishments Kitchens (commercial) Warehouses Mechanical Equipment Rooms Garages Auditoriums Theaters Copyright 2010

CD Technologies Asia, Inc.

28.00 18.60 18.60 18.60 1.80 1.40 1.40 1.40 4.60 4.60 4.60 8.40 7.40 7.40 7.40

Other than Elevators are Required Where Number Occupants is Over 10 10 10 10 50 50 50 50 50 50 50 5 5 5 5

3.25 28.00

6 10

2.80 2.80 5.609.30 46.50 18.60 1.40 18.60 28.00 28.00 9.30 0.65 0.65

50 50 10 30 10 30 30 50 30 30 10 50 50

Philippine Laws Premium Edition 2009

235

Churches and chapels Dance Floors Reviewing Stands Stadia

2.

Copyright 2010

0.65 0.65 0.65 0.65

50 50 50 50

Exits a.

Number of Exits. Every building or usable portion thereof shall have at least one (1) exit. In all occupancies, floors above the first storey having an occupant load of more than ten (10) shall not have less than two (2) exits. Each mezzanine floor used for other than storage purposes, if greater in area than 185 sq. meters or more than 18.00 meters in any dimension, shall have at least, two (2) stairways to an adjacent floor. Every storey or portion thereof, having an occupant load of 500 to 999 shall have at least three (3) exits. Every storey or portion thereof having an occupant load of one thousand (1000) or more shall have at least four (4) exits. The number of exits required from any storey of a building shall be determined by using the occupant loads of floors which exit through the level, under consideration as follows: 50% of the occupant load in the first adjacent storey above (and the first adjacent storey below, when a storey below exits through the level under consideration) and 25% of the occupant load in the storey immediately beyond the first adjacent storey. The maximum number of exits required for any storey shall be maintained until egress is provided from the structures. For purposes of this Section basement or cellars and occupied roofs shall be provided with exits as required for storeys. Floors above the second storey, basements and cellars used for other than service of the building shall have not less than two (2) exits.

b.

Width. The total width of exits in meters shall not be less than the total occupant load served divided by one hundred sixty five (165). Such width of exits shall be divided approximately equally among the separate exits. The total exit width required from any storey of a building shall be determined by using the occupant load of that storey plus the percentage of the occupant loads of floors which exits through the level under

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

236

consideration as follows: 50% of the occupant load in the first adjacent storey above (and the first adjacent storey below when a storey below exits through the level under consideration) and 25% of the occupant load In the storey immediately beyond the first adjacent storey. The maximum exit width from any storey of a building shall be maintained.

3.

Copyright 2010

c.

Arrangement of Exits. If only two (2) exits are required, they shall be placed a distance apart to not less than one-fifth (1/5) of the perimeter of the area served measured in a straight line between exits. Where three (3) or more exits are required, they shall be arranged a reasonable distance apart so that if one becomes blocked, the others will be available.

d.

Distance to Exits. No point in a building without a sprinkler system shall be more than 45.00 meters from an exterior exit door, a horizontal exit, exit passageway, or an enclosed stairway, measured along the line of travel. In a building equipped with a complete automatic fire extinguishing system, the distance from exits may be increased to 60.00 meters.

Doors. The provisions herein shall apply to every exit door serving an area having an occupant load of more than ten (10), or serving hazardous rooms or areas. a.

Swing. Exit door shall swing in the direction of exit travel when serving any hazardous areas or when serving an occupant load of fifty (50) or more. Double acting doors shall not be used as exits serving a tributary occupant load of more than one hundred (100); nor shall they be used as a part of fire assembly, nor equipped with panic hardware. A double acting door shall be provided with a view panel of not less than 1,300 sq. centimeters.

b.

Type of Lock or Latch. Exit door shall be openable from the inside without the use of a key or any special knowledge or effort: Except, that this requirement shall not apply to exterior exit doors in a Group E or F Occupancy if there is a conspicuous, readily visible and

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

237

durable sign on or adjacent to the door, stating that the door is to remain unlocked during business hours. The locking device must be of a type that will readily be distinguishable as locked. Flush bolts or surface bolts are prohibited. TCaADS

Copyright 2010

c.

Width and Height. Every required exit doorway shall be of a size as to permit the installation of a door not less than 900 millimeters in width and not less than 2.00 meters in height. When installed in exit doorways, exit doors shall be capable of opening at least 90 degrees and shall be so mounted that the clear width of the exitway is not less than 700 millimeters. In computing the required exit width the net dimension of the exitway shall be used.

d.

Door Leaf Width. No leaf of an exit door shall exceed 1.20 meters in width.

e.

Special Doors. Revolving, sliding, and overhead doors shall not be used as required exits.

f.

Egress from Door. Every required exit door shall give immediate access to an approved means of egress from the building.

g.

Change In Floor Level at Doors. Regardless of the occupant load, there shall be a floor or landing on each side of an exit door. The floor or landing shall be leveled with, or not more than 50 millimeters lower than the threshold of the doorway: Except, that in Group A and B Occupancies, a door may open on the top step of a flight of stairs or an exterior landing provided the door does not swing over the top step or exterior landing and the landing is not more than 200 millimeters below the floor level.

h.

Door Identification. Glass doors shall conform to the requirements in Section 1802. Other exit doors shall be so marked that they are readily distinguishable from the adjacent construction.

i.

Additional Doors. When additional doors are provided

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

238

for egress purposes, they shall conform to all provisions in the following cases: Approved revolving doors having leaves which will collapse under opposing pressures may be used in exit situations; provided; that such doors have a minimum width of 2.00 meters or they are not used in occupancies where exits are required to be equipped with panic hardware or at least one conforming exit door is located adjacent to each revolving doors installed in a building and the revolving door shall not be considered to provide any exit width. 4.

Copyright 2010

Corridors and Exterior Exit Balconies. The provisions herein shall apply to every corridor and exterior exit balcony serving as a required exit for an occupant load of more than ten (10). a.

Width. Every corridor or exit balcony shall not be less than 1.10 meters in width.

b.

Projections. The required width of corridors and exterior exit balconies shall be unobstructed. Except, that trim handrails, and doors when fully opened shall not reduce the required width by more than 200 millimeters. Doors in any position shall not reduce the required width of the corridor by more than one-half (1/2).

c.

Access to Exits. When more than one (1) exit is required, they shall be so arranged to allow going to either direction from any point in the corridor or exterior exit balcony to a separate exit, except for dead ends permitted by the Code.

d.

Dead Ends. Corridors and exterior exit balconies with dead ends are permitted when the dead end does not exceed 6.00 meters in length.

e.

Construction. Walls and ceilings of corridors shall not be less than one-hour fire-resistive construction. Provided, that this requirement shall not apply to exterior exit balconies, railings, and corridors of one-storey building housing a Group E and F Occupancy occupied by one (1) tenant only and which serves an occupant load of thirty (30) or less, nor to corridors, formed by temporary partitions. Exterior exit balconies shall not project into

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

239

an area where protected openings are required. f.

5.

Copyright 2010

ISDCHA

Openings. Where corridor wall are required to be one-hour fire-resistive construction, every interior door opening shall be protected as set forth in generally recognized and accepted requirements for dual-purpose fire exit doors. Other interior openings except ventilation louvers equipped with approved automatic fire shutters shall be 7 millimeters thick fixed wire glass set in steel frames. The total area of all openings other than doors, in any portion of an interior corridor wall shall not exceed 25% of the area of the corridor wall of the room being separated from the corridor.

Stairways. Except stairs or ladders used only to access equipment, every stairway serving any building or portion thereof shall conform to the following requirements: a.

Width. Stairways serving an occupant load of more than fifty (50) shall not be less than 1.10 meters. Stairways serving an occupant load of fifty (50) or less may be 900 millimeters wide. Private stairways serving an occupant load of less than ten (10) may be 750 millimeters. Trim and handrails shall not reduce the required width by more than 100 millimeters.

b.

Rise and Run. The rise of every step in a stairway shall not exceed 200 millimeters and the run shall not be less than 250 millimeters. The maximum variations in the height of risers and the width of treads in any one flight shall be 5 millimeters: Except, in case of private stairways serving an occupant load of less than ten (10), the rise may be 200 millimeters and the run may be 250 millimeters, except as provided in sub-paragraph (c) below.

c.

Winding Stairways. In Group A Occupancy and in private stairways in Group B Occupancies, winders may be used if the required width of run is provided at a point not more than 300 millimeters from the side of the stairway where the treads are narrower but in no case shall any width of run be less than 150 millimeters at any

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

240

point. d.

Circular Stairways. Circular stairs may be used as an exit provided the minimum width of run is not less than 250 millimeters. All treads in any one flight between landings shall have identical dimensions within a 5 millimeters tolerance.

e.

Landings. Every landing shall have a dimension measured in the direction of travel equal to the width of the stairway. Such dimension need not exceed 1.20 meters when the stairs has a straight run. Landings when provided shall not be reduced in width by more than 100 millimeters by a door when fully open.

f.

Basement Stairways. Where a basement stairway and a stairway to an upper storey terminate in the same exit enclosure, an approved barrier shall be provided to prevent persons from continuing on to the basements. Directional exit signs shall be provided as specified in the Code.

g.

Distance Between Landings. There shall be not more than 3.60 meters vertical distance between landings.

h.

Handrails. Stairways shall have handrails on each side and every stairway required to be more than 3.00 meters in width shall be provided with not less than one intermediate handrail for each 3.00 meters of required width. Intermediate handrails shall be spaced approximately equal within the entire width of the stairway. Handrails shall be placed not less than 800 millimeters nor more than 900 millimeters above the nosing of treads, and ends of handrails shall be returned or shall terminate in newel posts or safety terminals: Except, in the following cases: Stairways 1.10 meters or less in width and stairways serving one (1) individual dwelling unit in Group A or B Occupancies may have one handrail, except that such stairway, open on one or both, sides shall have handrails provided on the open side or sides: or stairways having less than four (4) risers need not have handrails. DTCSHA

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

241

i.

Exterior Stairway Protection. All openings in the exterior wall below or within 3.00 meters, measured horizontally, of an exterior exit stairway serving a building over two storeys in height shall be protected by a self-closing fire assembly having a three-fourth - hour fire-resistive rating; Except, that openings may be unprotected when two separated exterior stairways serve an exterior exit balcony.

j.

Stairway Construction i. Stairway Construction — Interior. Interior stairways shall be constructed as specified in this Code. Where there is enclosed usable space under the stairs the walls and soffits of the enclosed space shall be protected on the enclosed side as required for one-hour fire resistive construction. ii. Stairway Construction — Exterior. Exterior stairways shall be of incombustible material: Except, that on Type III buildings which do not exceed two storeys in height, which are located in less fire-restrictive Fire Zones, as well as on Type I buildings which may be of wood not less than 50 millimeters in nominal thickness. Exterior stairs shall be protected as required for exterior walls due to location on property as specified in the Code. Exterior stairways shall not project into an area where openings are required to be protected. Where there is enclosed usable space under stairs, the walls and soffits of the enclosed space shall be protected on the enclosed side as required for one-hour fire-resistive construction.

k.

Stairway to Roof. In every building four (4) or more storeys in height, one (1) stairway shall extend to the roof unless the roof has a slope greater than 1 in 3. IESAac

l.

Copyright 2010

Headroom. Every required stairway shall have a headroom clearance of not less than 2.00 meters. Such clearance shall be established by measuring vertically from a plane parallel and tangent to the stairway tread nosing to the soffit above all points.

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

242

Copyright 2010

6.

Ramps. A ramp conforming to the provisions of the Code may be used as an exit. The width of ramps shall be as required for corridors.

7.

Horizontal Exit. If conforming to the provisions of the Code, a horizontal exit may be considered as the required exit. All openings in a separation wall shall be protected by a fire assembly having a fire-resistive rating of not less than one hour. A horizontal exit shall not lead into a floor area having a capacity for an occupant load not less than the occupant load served by such exit. The capacity shall be determined by allowing 0.30 sq. meter of net floor area per ambulatory occupant and 1.90 sq. meters per non-ambulatory occupant. The dispersal area into which the horizontal exit leads shall be provided with exits as required by the Code.

8.

Exit Enclosure. Every Interior stairway, ramp, or escalator shall be enclosed as specified in the Code; Except, that in other than Group D Occupancies, an enclosure will not be required for stairway, ramp, or escalator serving only one adjacent floor and not connected with corridors or stairways serving other floors. Stairs in Group A Occupancies need not be enclosed. a.

Enclosure walls shall not be less than two-hour fire-resistive construction. There shall be no openings into exit enclosures except exit doorways and openings in exterior walls. All exit doors in an exit enclosure shall be appropriately protected.

b.

Stairway and ramp enclosures shall include landings and parts of floors connecting stairway flights and shall include a corridor on the ground floor leading from the stairway to the exterior of the building. Enclosed corridors or passageways are not required for unenclosed stairways.

c.

A stairway in an exit enclosure shall not continue below the grade level exit unless an approved barrier is provided at the ground floor level to prevent persons from accidentally continuing into the basement.

d.

There shall be no enclosed usable space under stairways in an exit enclosure, nor shall the open space under such

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

243

stairways be used for any purpose. 9.

caITAC

Smokeproof Enclosures

A smokeproof enclosure shall consist of a vestibule and a continuous stairway enclosed from the highest point to the lowest point by walls of two-hour fire-resistive construction. In buildings five (5) storeys or more in height, one of the required exits shall be a smokeproof enclosure.

10.

a.

Stairs in smokeproof enclosures incombustible construction.

shall

be

of

b.

There shall be no openings in smokeproof enclosures, except exit doorways and openings in exterior walls. There shall be no openings directly into the interior of the building. Access shall be through a vestibule with one (1) wall at least 50% open to the exterior and having an exit door from the interior of the building and an exit door leading to the smokeproof enclosure. In lieu of a vestibule, access may be by way of an open exterior balcony of incombustible materials.

c.

The opening from the building to the vestibule or balcony shall be protected with a self-closing fire assembly having one-hour fire-resistive rating. The opening from the vestibule or balcony to the stair tower shall be protected by a self-closing fire assembly having a one-hour fire-resistive rating.

d.

A smokeproof enclosure shall exit into a public way or into an exit passageway leading to a public way. The exit passageway shall be without other openings and shall have walls, floors, and ceilings of two-hour fire-resistance.

e.

A stairway in a smokeproof enclosure shall not continue below the grade level exit unless an approved barrier is provided at a ground floor level to prevent persons from accidentally walking into the basement.

Exit Outlets, Courts, and Passageways

Every exit shall discharge into a public way, exit court, or exit passageway. Every exit court shall discharge into a public way or an exit passageway. Passageways shall be Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

244

without openings other than required exits and shall have walls, floors, and ceilings of the same period of fire-resistance as the walls, floors and ceilings of the building but shall not be less than one-hour fire-resistive construction. aAHISE

a.

Width Every exit court and exit passageways shall be at least as wide as the required total width of the tributary exits, such required width being based on the occupant load served. The required width of exit courts or exit passageways shall be unobstructed except as permitted in corridors. At any point where the width of an exit court is reduced from any cause, the reduction in width shall be affected gradually by a guardrail at least 900 millimeters in height. The guardrail shall make an angle of not more than 30° with the axis of the exit court.

b.

Slope The slope of exit courts shall not exceed 1 in 10. The slope of exit passageway shall not exceed 1 in 8.

c.

Number of Exits Every exit court shall be provided with exits as required in the Code. cHaCAS

d.

Openings All openings into an exit court less than 3.00 meters wide shall be protected by fire assemblies having not less than three-fourth — hour fire-resistive rating. Except, that openings more than 3.00 meters above the floor of the exit court may be unprotected.

11.

Exit Signs and Illuminations Exits shall be illuminated at any time the building is occupied with lights having an intensity of not less than 10.7 LUX at floor level; Except, that for Group A Occupancies, the exit illumination shall be provided with separate circuits or separated sources of power (but not necessarily separate from exit signs when these are required for exit sign illumination).

12. Copyright 2010

Aisles

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

245

Every portion of every building in which are installed seats, tables, merchandise, equipment, or similar materials shall be provided with aisles leading to an exit. a.

Width Every aisle shall be not less than 800 millimeters wide if serving only one side, and not less than 1.00 meter wide if serving both sides. Such minimum width shall be measured at the point farthest from an exit, cross aisle, or foyer and shall be increased by 30 millimeters for every meter in length towards the exit, cross aisle or foyer.

Side aisles shall not be less than 1.10 meters in width. b.

Exit Distance In areas occupied by seats and in Groups H and I Occupancies without seats, the line of travel to an exit door by an aisle shall be not more than 45.00 meters. With standard spacing, as specified in the Code, aisles shall be so located that there will be not more than seven (7) seats between the wall and an aisle and not more than fourteen (14) seats between aisles. The number of seats between aisles may be increased to thirty (30) where exits doors are provided along each side aisle of the row of seats at the rate of one (1) pair of exit doors for every five (5) rows of seats, provided further that the distance between seats back to back is at least 1.00 meter. Such exit doors shall provide a minimum clear width of 1.70 meters. TSacCH

c.

Cross Aisles Aisles shall terminate in a cross aisle, foyer, or exit. The width of the cross aisle shall be not less than the sum of the required width of the widest aisle plus 50% of the total required width of the remaining aisle leading thereto. In Groups C, H and E Occupancies, aisles shall not be provided a dead end greater than 6.00 meters in length.

d.

Vomitories Vomitories connecting the foyer or main exit with the cross aisles shall have a total width not less than the sum of the

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

246

required width of the widest aisles leading thereto plus 50% of the total required width of the remaining aisles leading thereto. e.

Slope The slope portion of aisles shall not exceed a fall of 1 in 8.

13.

Seats a.

Seat Spacing With standard seating, the spacing of rows of seats from back-to-back shall be not less than 840 millimeters. With continental seating, the spacing of rows of unoccupied seats shall provide a clear width measured horizontally, as follows: 450 millimeters clear for rows of eighteen (18) seats or less; 500 millimeters clear for rows of thirty five (35) seats or less; 525 millimeters clear for rows of forty five (45) seats or less; and 550 millimeters clear for rows of forty six (46) seats or more.

b.

Width The width of any seat shall be not less than 450 millimeters.

14.

Reviewing Stands, Grandstands, and Bleachers a.

Height of Stands Stands made of combustible framing shall be limited to eleven (11) rows or 2.70 meters in height.

b.

Design Requirements The minimum unit live load for reviewing stands, grandstands, and bleachers shall be 500 kilograms per square meter of horizontal projection for the structure as a whole. Seat and footboards shall be 180 kilograms per linear meter. The sway force, applied to seats, shall be 35 kilograms per linear meter parallel to the seats and 15 kilograms per linear meter perpendicular to the seats. Sway forces need not be applied simultaneously with other lateral forces.

c. Copyright 2010

Spacing of Seats

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

247

i.

Row Spacing

The minimum spacing of rows of seats measured from back-to-back shall be: 600 millimeters for seats without backrests in open air stands; 750 millimeters for seats with backrests; and 850 millimeters for chair seating. There shall be a space of not less than 300 millimeters between the back of each seat and the front of the seat immediately behind it. ii.

Rise Between Rows

The maximum rise from one row of seats to the next shall not exceed 400 millimeters. DAHaTc

iii.

Seating Capacity

For determining the seating capacity of a stand, the width of any seat shall not be less than 450 millimeters nor more than 480 millimeters. iv.

Number of Seats Between Aisles

The number of seats between any seat and an aisle shall not be greater than fifteen (15) for open air stands with seats without backrests, a far open air stands with seats having backrests and seats without backrests within buildings and six (6) for seats with backrests in buildings. d.

Aisles i.

Aisles Required

Aisles shall be provided in all stands; Except, that aisles may be omitted when all the following conditions exist: Seats are without backrests; the rise from row to row does not exceed 300 millimeters per row; the number of rows does not exceed eleven (11) in height; the top seating board is not over 3.00 meters above grade; and the first seating board is not more than 500 millimeters above grade.

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

248

ii.

Obstructions

No obstruction shall be placed in the required width of any aisle or exitway. iii.

Stairs Required

When an aisle is elevated more than 200 millimeters above grade, the aisle shall be provided with a stairway or ramp whose width is not less than the width of the aisle. iv.

Dead End

No vertical aisle shall have a dead end more than sixteen (16) rows in depth regardless of the number of exits required. v.

Width

Aisles shall have a minimum width of 1.10 meters. e.

Stairs and Ramps The requirements in the Code shall apply to all stairs and ramps except for portions that pass through the seating area. i.

Stair Rise and Run

The maximum rise of treads shall not exceed 200 millimeters and the minimum width of the run shall be 280 millimeters. The maximum variation in the width of treads in any one (1) flight shall not be more than 5 millimeters and the maximum variation in one (1) height of two (2) adjacent rises shall not exceed 5 millimeters. ii.

Ramp Slope

The slope of a ramp shall not exceed 1 in 8. Ramps shall be roughened or shall be of approved non-slip material. iii.

Handrails

A ramp with a slope exceeding 1 in 10 shall have handrails. Stairs for stands shall have handrails. Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

249

Handrails shall conform to the requirements of the Code. f.

Guardrails i. Guardrails shall be required in all locations where the top of a seat plank is more than 1.20 meters above the grade and at the front of stands elevated more than 600 millimeters above grade. Where only sections of stands are used, guardrails shall be provided as required in the Code. ii. Railings shall be 1.10 meters above the rear of a seat plank or 1.10 meters above the rear of the steps in an aisle when the guardrail is parallel and adjacent to the aisle; Except, that the height may be reduced to 900 millimeters for guardrails located in front of the grandstand. iii. A midrail shall be placed adjacent to any seat to limit the open distance above the top of any part of a seat to 250 millimeters where the seat is at the extreme end or at the extreme rear of the bleachers or grandstand. The intervening space shall have one additional rail midway in the opening; Except, that railings may be omitted when stands are placed directly against a wall or fence giving equivalent protection; stairs and ramps shall be provided with guardrails. Handrails at the front of stands and adjacent to an aisle shall be designed to resist a load of 75 kilograms per linear meter applied at the top rail. Other handrails shall be designed to resist a load of 40 kilograms per linear meter. TcSICH

g.

Foot Boards Footboards shall be provided for all rows of seats above the third (3rd) row or beginning at such point where the seating plank is more than 600 millimeters above grade.

h.

Exits i.

Distance to Exit

The line of travel to an exit shall not be more than 45.00 meters. For stands with seats without backseats, this Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

250

distance may be measured by direct line from a seat to the exit from the stand. ii.

Aisle Used as Exit

An aisle may be considered as only one (1) exit unless it is continuous at both ends to a legal building exit or to a safe dispersal area. cIADaC

iii.

Two (2) Exits Required

A stand with the first (1st) seating board not more than 500 millimeters above grade of floor may be considered to have two (2) exits when the bottom of the stand is open at both ends. Every stand or section of a stand within a building shall have at least two means of egress when the stand accommodates more than fifty (50) persons. Every open air stand having seats without backrests shall have at least two (2) means of egress when the stand accommodates more than three hundred (300) persons. iv.

Three (3) Exits Required

Three (3) exits shall be required for stands within a building when there are more than 300 occupants within a stand and for open air stands with seats without backrests where a stand or section of a stand accommodates more than one thousand (1000) occupants. aTHASC

v.

Four (4) Exits Required

Four (4) exits shall be required when a stand or section of a stand accommodates more than 1000 occupants; Except, that for an open air stand with seats without backrest four (4) exits need not be provided unless there are accommodations for more than three thousand (3000) occupants. vi.

Width

The total width of exits in meters shall not be less than the total occupant load served divided by one hundred Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

251

sixty five (165); Except, that for open air stands with seats without backrest the total width of exits in meters shall be not less than the total occupant load served divided by five hundred (500) when exiting by stairs, and divided by six hundred fifty (650) when exiting by ramps or horizontally. When both horizontal and stair exits are used, the total width of exits shall be determined by using both figures as applicable. No exit shall be less than 1.10 meters in width. Exits shall be located at a reasonable distance apart. When only two (2) exits are provided, they shall be spaced not less than one-fifth (1/5) of the perimeter apart. i.

Securing of Chairs Chairs and benches used on raised stands shall be secured to the platforms upon which they are placed; Except, that when less than twenty five (25) chairs are used upon a single raised platform the fastening of seats to the platform may be omitted. When more than five hundred (500) loose chairs are used in connection with athletic events, chairs shall be fastened together in groups of not less than three (3), and shall be tied or staked to the ground.

j.

Safe Dispersal Area Each safe dispersal area shall have at least two (2) exits. If more than six thousand (6000) persons are to be accommodated within such an area, there shall be a minimum of three (3) exits, and for more than nine thousand (9000) persons there shall be a minimum of four (4) exits. The aggregate clear width of exits from a safe dispersal area shall be determined on the basis of not less than one (1) exit unit of 600 millimeters for each five hundred (500) persons to be accommodated and no exit shall be less than 1.10 meters in width, a reasonable distance apart that shall be spaced not less than one-fifth (1/5) of the perimeter of the area apart from each other.

15.

Special Hazards a.

Boiler Rooms Except in Group A Occupancies, every boiler room and every

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

252

room containing an incinerator or liquefied petroleum gas or liquid fuel-fired equipment shall be provided with at least two (2) means of egress, one of which may be a ladder. All interior openings shall be protected as provided for in the Code. ITCcAD

b.

Cellulose Nitrate Handling Film laboratories, projection rooms, and nitro-cellulose processing rooms shall have not less than two exits.

SECTION 1208. Skylights. —

Copyright 2010

1.

All skylights shall be constructed with metal frames except those for Groups A and J Occupancies. Frames of skylights shall be designed to carry loads required for roofs. All skylights, the glass of which is set at an angle of less than 45º from the horizontal, if located above the first storey, shall be set at least 100 millimeters above the roof. Curbs on which the skylights rest shall be constructed of incombustible materials except for Types I or II Construction.

2.

Spacing between supports in one direction for flat wired glass in skylights shall not exceed 625 millimeters. Corrugated wired glass may have supports 1.50 meters apart in the direction of the corrugation. All glass in skylights shall be wired glass; Except, that skylights over vertical shafts extending through two (2) or more storeys shall be glazed with plain glass as specified in the Code; Provided, that wired glass may be used in ventilation equal to not less than one-eight (1/8) the cross-sectional area of the shaft but never less than 1.20 meters provided at the top of such shaft. Any glass not wired glass shall be protected above and below with a screen constructed of wire not smaller than 2.5 millimeters in diameter with a mesh not larger than 25 millimeters. The screen shall be substantially supported below the glass.

3.

Skylights installed for the use of photographers may be constructed of metal frames and plate glass without wire netting.

4.

Ordinary glass may be used in the roof and skylights for greenhouses, Provided, that height of the greenhouses at the ridge does not exceed 6.00 meters above the grade. The use of

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

253

wood in the frames of skylights will be permitted in greenhouses outside of highly restrictive Fire Zones if the height of the skylight does not exceed 6.00 meters above the grade, but in other cases metal frames and metal sash bars shall be used. 5.

Glass used for the transmission of light, if placed in floors or sidewalks, shall be supported by metal or reinforced concrete frames, and such glass shall not be less than 12.5 millimeters in thickness. Any such glass over 100 sq. centimeters in area shall have wire mesh embedded in the same or shall be provided with a wire screen underneath as specified for skylights in the Code. All portions of the floor lights or sidewalk lights shall be of the same strength as required for floor or sidewalk construction, except in cases where the floor is surrounded by a railing not less 1.10 meters in height, in which case the construction shall be calculated for not less than roof loads.

SECTION 1209. Bays, Porches, and Balconies. — Walls and floors in bay and oriel windows shall conform to the construction allowed for exterior walls and floors of the type of construction of the building to which they are attached. The roof covering of a bay or oriel window shall conform to the requirements of the roofing of the main roof. Exterior balconies attached to or supported by wall required to be of masonry, shall have brackets, or beams constructed of incombustible materials. Railings shall be provided for balconies, landings, or porches which are more than 750 millimeters above, grade. SECTION 1210. Penthouses and Roof Structures. — 1.

Height No penthouse or other projection above the roof in structures of other than Type V construction shall exceed 8.40 meters above the roof when used as an enclosure for tanks or for elevators which run to the roof and in all other cases shall not extend more than 3.60 meters in height with the roof. DSETac

2.

Area The aggregate area of all penthouses and other roof structures shall not exceed one third (1/3) of the area of the supporting roof.

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

254

3.

Prohibited Uses No penthouse, bulkhead, or any other similar projection above the roof shall be used for purposes other than shelter of mechanical equipment or shelter of vertical shaft openings in the roof. A penthouse or bulkhead used for purposes other than that allowed by this Section shall conform to the requirements of the Code for an additional storey.

4.

Construction Roof structures shall be constructed with walls, floors, and roof as required for the main portion of the building except in the following cases: a.

On Types III and IV constructions, the exterior walls and roofs of penthouses which are 1.50 meters or more from an adjacent property line may be of one-hour fire-resistive incombustible construction. IDAaCc

b.

Walls not less than 1.50 meters from an exterior wall of a Type IV construction may be of one-hour fire-resistive incombustible construction. The above restrictions shall not prohibit the placing of wood flagpoles or similar structures on the roof of any building.

5.

Towers and Spires Towers and spires when enclosed shall have exterior walls as required for the building to which they are attached. Towers not enclosed and which extend more than 20.00 meters above the grade shall have their framework constructed of iron, steel, or reinforced concrete. No tower or spire shall occupy more than one-fourth (1/4) of the street frontage of any building to which it is attached and in no case shall the base area exceed 150.00 sq. meters unless it conforms entirely to the type of construction requirements of the building to which it is attached and is limited in height as a main part of the building. If the area of the tower and spire exceeds 10.00 sq. meters on any horizontal cross section, its supporting frames shall extend directly to the ground. The roof covering of the spires shall be as required for the main room of the rest of the structure. Skeleton towers used as radio masts, neon signs, or advertisement frames and placed on the roof of any building shall be constructed entirely of incombustible materials when more than 7.50

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

255

meters in height, and shall be directly supported on an incombustible framework to the ground. No such skeleton towers shall be supported on roofs of combustible framings. They shall be designed to withstand a wind load from any direction in addition to any other loads. SECTION 1211. Chimneys, Fireplaces, and Barbecues. — 1.

Chimneys a.

Structural Design Chimneys shall be designed, anchored, supported, reinforced, constructed, and installed in accordance with generally accepted principles of engineering. Every chimney shall be capable of producing a draft at the appliance not less than that required for the safe operation of the appliance connected thereto. No chimney shall support any structural load other than its own weight unless it is designed to act as a supporting member. Chimneys in a wood-framed building shall be anchored laterally at the ceiling line and at each floor line which Is more than 1.80 meters above grade, except when entirely within the framework or when designed to be free standing.

b.

Walls Every masonry chimney shall have walls of masonry units, bricks, stones, listed masonry chimney units, reinforced concrete or equivalent solid thickness of hollow masonry and lined with suitable liners in accordance with the following requirements: i.

Masonry Chimneys for Residential Type Appliances Masonry chimneys shall be constructed of masonry units or reinforced concrete with walls not less than 100 millimeters thick; or of rubble stone masonry not less than 300 millimeters thick. The chimney liner shall be in accordance with the Code.

ii.

Masonry Chimneys for Low Heat Appliances Masonry chimneys shall be constructed of masonry units or reinforced concrete with walls not less than 200 millimeters thick; Except, that rubble stone masonry

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

256

shall be not less than 300 millimeters thick. The chimney liner shall be in accordance with the Code. CADacT

iii.

Masonry Chimneys for Medium-Heat Appliances Masonry chimneys for medium-heat appliances shall be constructed of solid masonry units of reinforced concrete not less than 200 millimeters thick, Except, that stone masonry shall be not less than 300 millimeters thick and, in addition shall be lined with not less than 100 millimeters of firebrick laid in a solid bed of fire clay mortar with solidly filled head, bed, and wall joints, starting not less than 600 millimeters below the chimney connector entrance. Chimneys extending 7.50 meters or less above the chimney connector shall be lined to the top.

iv.

Masonry Chimneys for High-Heat Appliances Masonry chimneys for high-heat appliances shall be constructed with double walls of solid masonry units or reinforced concrete not less than 200 millimeters in thickness, with an air space of not less than 50 millimeters between walls. The inside of the interior walls shall be of firebrick not less than 100 millimeters in thickness laid in a solid bed of fire clay mortar with solidly filled head, bed, and wall joints.

v.

Masonry Chimneys for incinerators installed in Multi-Storey Buildings (Apartment-Type Incinerators) Chimneys for incinerators installed in multi-storey buildings using the chimney passageway as a refuse chute where the horizontal grate area of combustion chamber does not exceed 0.80 sq. meter shall have walls of solid masonry or reinforced concrete, not less than 100 millimeters thick with a chimney lining as specified in the Code. If the grate area of such an incinerator exceeds 0.80 sq. meter, the walls shall not be less than 100 millimeters of firebrick except that higher than 9.00 meters above the roof of the combustion chamber, common brick alone 200 millimeters in thickness may be used. cIADTC

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

257

vi.

Masonry Chimneys for Commercial and Industrial Type Incinerators Masonry chimneys for commercial and industrial type incinerators of a size designed for not more than 110 kilograms of refuse per hour and having a horizontal grate area not exceeding 0.50 sq. meter shall have walls of solid masonry or reinforced concrete not less than 100 millimeters thick with lining of not less than 100 millimeters of firebrick, which lining shall extend for not less than 12.00 meters above the roof of the combustion chamber. If the design capacity of grate area of such an incinerator exceeds 110 kilograms per hour and 0.80 sq. meter respectively, walls shall not be less than 200 millimeters thick, lined with not lea than 100 millimeters of firebrick extending the full height of the chimney. HCTEDa

c.

Linings Fire clay chimney lining shall not be less than 15 millimeters thick. The lining shall extend from 200 millimeters below the lowest inlet or, in the case of fireplace, from the throat of the fireplace to a point above enclosing masonry walls. Fire clay chimney linings shall be installed ahead of the construction of the chimney as it is carried up, carefully bedded one on the other in fire clay mortar, with close-fitting joints left smooth on the inside. Firebrick not less than 500 millimeters thick may be used in place of fire clay chimney.

d.

Area No chimney passageway shall be smaller in area than the vent connection of the appliance attached thereto.

e.

Height Every masonry chimney shall extend at least 600 millimeters above the part of the roof through which it passes and at least 600 millimeters above the highest elevation of any part of a building within 3.00 meters to the chimney.

f.

Copyright 2010

Corbeling

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

258

No masonry chimney shall be corbeled from a wall more than 150 millimeters nor shall a masonry chimney be corbeled from a wall which is less than 300 millimeters in thickness unless it projects equally on each side of the wall. In the second (2nd) storey of a two-storey building of Group A Occupancy, corbeling of masonry chimneys on the exterior of the enclosing walls may equal the wall thickness. In every case the corbeling shall not exceed 25 millimeters projection for each course of brick. g.

Change in Size or Shape No change in the size or shape of a masonry chimney shall be made within a distance of 150 millimeters above or below the roof joints or rafters where the chimney passes through the roof.

h.

Separation When more than one passageway is contained in the same chimney, masonry separation at least 100 millimeters thick bonded into the masonry wall of the chimney shall be provided to separate passageways. THEDCA

i.

Inlets Every Inlet to any masonry chimney shall enter the side thereof and shall be of not less than 3 millimeters thick metal or 16 millimeters refractory material.

j.

Clearance Combustible materials shall not be placed within 50 millimeters of smoke chamber or masonry chimney walls when built within a structure, or within 25 millimeters when the chimney is built entirely outside the structure.

k.

Termination All incinerator chimneys shall terminate in a substantially constructed spark arrester having a mesh not exceeding 20 millimeters.

l. Copyright 2010

Cleanouts

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

259

Cleanout openings shall be provided at the base of every masonry chimney. 2.

Fireplaces and Barbecues Fireplaces, barbecues, smoke chambers, and fireplace chimneys shall be of solid masonry or reinforced concrete and shall conform to the minimum requirements specified in the Code. a.

Fireplace Walls Walls of fireplaces shall not be less than 200 millimeters in thickness. Walls of fireboxes shall not be less than 250 millimeters in thickness; Except, that where a lining of firebrick is used, such walls shall not be less than 200 millimeters in thickness. The firebox shall not be less than 500 millimeters in depth. The maximum thickness of joints in firebrick shall be 10 millimeters.

b.

Hoods Metal hoods used as part of a fireplace or barbecue shall be not less than No. 18 gauge copper, galvanized iron, or other equivalent corrosion-resistant ferrous metal with all seams and connections of smokeproof unsoldered construction. The hoods shall be sloped at an angle of 45º or less from the vertical and shall extend horizontally at least 150 millimeters beyond the limits of the firebox. Metal hoods shall be kept a minimum of 400 millimeters from combustible materials.

c.

Circulators Approved metal heat circulators may be installed in fireplaces.

d.

Smoke Chamber Front and side walls shall not be less than 200 millimeters in thickness. Smoke chamber back walls shall not be less than 150 millimeters in thickness.

e.

Fireplace Chimneys Walls of chimneys without flue lining shall not be less than 200 millimeters in thickness. Walls of chimneys with flue lining

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

260

shall not be less than 100 millimeters in thickness and shall be constructed in accordance with the requirements of the Code. IaECcH

f.

Clearance to Combustible Materials Combustible materials shall not be placed within 50 millimeters of fireplace, smoke chamber, or chimney walls when built entirely within a structure, or within 25 millimeters when the chimney is built entirely outside the structure. Combustible materials shall not be placed within 150 millimeters of the fireplace opening. No such combustible material within 300 millimeters of the fireplace opening shall project more than 3 millimeters for each 25 millimeters clearance from such opening. No part of metal hoods used as part of a fireplace, barbecue or heating stoves shall be less than 400 millimeters from combustible material. This clearance may be reduced to the minimum requirements set forth in the Code. g.

Area of Flues, Throats, and Dampers

The net cross-sectional area of the flue and of the throat between the firebox and the smoke chamber of a fireplace shall not be less than the requirements to be set forth by the Secretary. Where dampers are used, they shall be of not less than No. 12 gauge metal. When fully opened, damper opening shall be not less than 90% of the required flue area. When fully open, damper blades shall not extend beyond the line of the inner face of the flue. h.

Lintel Masonry over the fireplace opening shall be supported by a noncombustible lintel. ICDcEA

i.

Hearth Every fireplace shall be provided with a brick, concrete, stone, or other approved noncombustible hearth slab at least 300 millimeters wider on each side than the fireplace opening and projecting at least 450 millimeters therefrom. This slab shall not be less than 100 millimeters thick and shall be supported by a noncombustible material or reinforced to carry its own weight

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

261

and all imposed loads. SECTION 1212. Fire-Extinguishing Systems. — 1.

2.

Fire-Extinguishing Systems — Where required, standard automatic fire extinguishing systems shall be installed in the following places, and in the manner provided in the Code. a.

In every storey, basement or cellar with an area of 200.00 sq. meters or more which is used for habitation, recreation, dining, study, or work, and which has an occupant load of more than twenty (20).

b.

In all dressing rooms, rehearsal rooms, workshops or factories, and other rooms with an occupant load of more than ten (10) or assembly halls under Group H and I Occupancies with occupant load of more than five hundred (500), and if the next doors of said rooms are more than 30.00 meters from the nearest safe fire dispersal area of the building or opening to an exit court or street.

c.

In all rooms used for storage or handling of photographic x-ray nitrocellulose films and other inflammable articles.

Dry Standpipes — Every building four (4) or more storeys in height shall be equipped with one or more dry standpipes. a.

Construction and Tests — Dry standpipes shall be of wrought iron or galvanized steel and together with fittings and connections shall be of sufficient strength to withstand 20 kilograms per square centimeter of water pressure when ready for service, without leaking at the joints, valves, or fittings. Tests shall be conducted by the owner or the building contractor in the presence of a representative of the Building Official whenever deemed necessary for the purpose of certification of its proper function. HDaACI

b.

Copyright 2010

Size — Dry standpipes shall be of such size as to be capable of delivering 900 liters of water per minute from each of any three (3) outlets simultaneously under the pressure created by one (1) fire engine or pumper based

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

262

on the standard equipment available. c.

Number Required — Every building four (4) or more storeys in height where the area of any floor above the third (3rd) floor is 950 sq. meters or less, shall be equipped with at least one (1) dry standpipe and an additional standpipe shall be installed for each additional 950 sq. meters or fraction thereof.

d.

Location — Standpipes shall be located within enclosed stairway landings or near such stairways as possible or immediately inside of an exterior wall and within 300 millimeters of an opening in a stairway enclosure of the balcony or vestibule of a smokeproof tower or an outside exit stairway.

e.

Siamese Connections — Subject to the provisions of subparagraph (b) all 100 millimeters dry standpipes shall be equipped with a two-way Siamese fire department connection. All 125 millimeters dry standpipes shall be equipped with a three-way Siamese fire department connection, and 150 millimeters dry standpipes shall be equipped with four-way Siamese fire department connections. All Siamese inlet connections shall be located on a street-front of the building and not less than 300 millimeters nor more than 1.20 meters above the grade and shall be equipped with a clapper checks and substantial plugs. All Siamese inlet connections shall be recessed in the wall or otherwise substantially protected.

f.

Outlets — All dry standpipes shall extend from the ground floor to and over the roof and shall be equipped with a 63 millimeters outlet nor more than 1.20 meters above the floor level at each storey. All dry standpipes shall be equipped with a two-way 63 millimeters outlet above the roof. All outlets shall be equipped with gate valves. Tide

g.

Copyright 2010

Signs — An iron or bronze sign with raised letters at least 25 millimeters high shall be rigidly attached to the building adjacent to all Siamese connections and such signs shall read: "CONNECTION TO DRY

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

263

STANDPIPE". 3.

Wet Standpipes — Every Group H and I Occupancy of any height, and every Group C Occupancy of two (2) more storeys in height, and every Group B, D, E, F and G Occupancy of three (3) or more storeys in height and every Group G and E Occupancy over 1800 sq. meters in area shall be equipped with one or more interior wet standpipes extending from the cellar or basement into the topmost storey; Provided, that Group H buildings having no stage and having a seating capacity of less than five hundred (500) need not be equipped with interior wet standpipes. a.

Construction — Interior wet standpipes shall be constructed of the same materials as those required for dry standpipes.

b.

Size i.

Interior wet standpipes shall have an internal diameter sufficient to deliver 190 liters of water per minute under 2.00 kilograms per square centimeter pressure at the hose connections. Buildings of Group H and I Occupancy shall have wet standpipes systems capable of delivering the required quantity and pressure from any two (2) outlets simultaneously; for all other Occupancies only one (1) outlet need be figured to be opened at one time. In no case shall the internal diameter of a wet standpipe be less than 50 millimeters, except when the standpipe is attached to an automatic fire-extinguishing system. HTCDcS

ii.

Copyright 2010

Any approved formula which determines pipe sizes on a pressure drop basis may be used to determine pipe size for wet standpipe systems. The Building Official may require discharge capacity and pressure tests on completed wet standpipe systems.

c.

Number required — The number of wet standpipes when required in the Code shall be so determined that all portions of the building are within 6.00 meters of a nozzle attached to a hose 23.00 meters in length.

d.

Location — In Group H and I Occupancies, outlets shall

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

264

be located as follows: one (1) on each side of the stage, one (1) at the rear of the auditorium, and one (1) at the rear of the balcony. Where occupant loads are less than five hundred (500) the above requirements may be waived; Provided, that portable fire extinguishers of appropriate capacity and type are installed within easy access from the said locations. In Group B, C, D, E, F and G Occupancies, the location of all interior wet standpipes shall be in accordance with the requirement for dry standpipes; Provided, that at least one (1) standpipe is installed to cover not more than 650 sq. meters. ESDcIA

Copyright 2010

e.

Outlets. — All interior wet standpipes shall be equipped with a 38 millimeter valve in each storey, including the basement or cellar of the building, and located not less than 300 millimeters nor more than 1.20 meters above the floor.

f.

Threads. — All those threads used in connection with the installation of such standpipes, including valves and reducing fittings shall be uniform with that prescribed by the Secretary.

g.

Water Supply. — All interior wet standpipes shall be connected to a street main not less than 100 millimeters in diameter, or when the water pressure is insufficient, to a water tank of sufficient size as provided in subparagraph (h). When more than one (1) interior wet standpipe is required in the building, such standpipe shall be connected at their bases or at their tops by pipes of equal size.

h.

Pressure and Gravity Tanks — Tanks shall have a capacity sufficient to furnish at least 1,500 liters per minute for a period of not less than 10 minutes. Such tanks shall be located so as to provide not less than 2 kilograms per square centimeter pressure at the topmost base outlet for its entire supply. Discharge pipes from pressure tanks shall extend 50 millimeters into and above the bottom of such tanks. All tanks shall be tested in place after installation and proved tight at a hydrostatic

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

265

pressure 50% in excess of the working pressure required. Where such tanks are used for domestic purposes the supply pipe for such purposes shall be located at or above the center line of such tanks. Incombustible supports shall be provided for all such supply tanks and not less than a 900 millimeters clearance shall be maintained over the top and under the bottom of all pressure tanks. i.

Fire pumps. — Fire pumps shall have a capacity of not less than 1,000 liters per minute with a pressure not less than 2 kilograms per square centimeter at the topmost hose outlet. The source of supply for such pump shall be a street water main of not less than 100 millimeters diameter or a well or cistern containing a one-hour supply. Such pumps shall be supplied with an adequate source of power and shall be automatic in operation. TaHDAS

j.

4.

Hose and Hose Reels — Each hose outlet of all interior wet standpipes shall be supplied with a hose not less than 38 millimeters in diameter. Such hose shall be equipped with a suitable brass or bronze nozzle and shall be not over 23.00 meters in length. An approved standard form of wall hose reel or rack shall be provided for the hose and shall be located so as to make the hose readily accessible at all times and shall be recessed in the walls or protected by suitable cabinets.

Basement Pipe Inlets — Basement pipe inlets shall be installed in the first (1st) floor of every store, warehouse, or factory where there are cellars or basements under same; Except, where in such cellars or basements there is installed a fire-extinguishing system as specified in the Code or where such cellars or basements are used for banking purposes, safe deposit vaults, or similar uses. aETADI

a.

Copyright 2010

Material — All basement pipe inlets shall be of cast iron, steel, brass, or bronze with lids of cast brass or bronze and shall consist of a sleeve not less than 200 millimeters in diameter through the floor extending to and flush with the ceiling below and with a top flange, recessed with an inside shoulder, to receive the lid and

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

266

flush with the finished floor surface. The lid shall be a solid casting and shall have a ring lift recessed on the top thereof, so as to be flushed. The lid shall have the words "FOR FIRE DEPARTMENT ONLY, DO NOT COVER UP" cast on the top thereof. The lid shall be installed in such a manner as to permit its removal readily from the inlet. b.

5.

Location. — Basement pipe inlets shall be strategically located and kept readily accessible at all times to the Fire Department.

Approval — All fire-extinguishing systems, including automatic sprinklers, wet and dry standpipes, automatic chemical extinguishers, basement pipe inlets, and the appurtenances thereto shall meet the approval of the Fire Department as to installation and location and shall be subject to such periodic test as it may require.

SECTION 1213. Stages and Platform. — 1.

Copyright 2010

Stage Ventilators — There shall be one (1) or more ventilators constructed of metal or other incombustible material near the center and above the highest part of any working stage raised above the stage roof and having a total ventilation area equal to at least 5% of the floor area within the stage walls. The entire equipment shall conform to the following requirements: a.

Opening Action — Ventilators shall open by spring action or force of gravity sufficient to overcome the effects of neglect, rust, dirt, or expansion by heat or warping of the framework.

b.

Glass — Glass, if used in ventilators, must be protected against falling on the stage. A wire screen, if used under the glass, must be so placed that if clogged it cannot reduce the required ventilating area or interfere with the operating mechanism or obstruct the distribution of water from the automatic fire extinguishing systems.

c.

Design — Ventilators, penthouses, and supporting framework shall be designed in accordance with the Code.

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

267

d.

Spring Actuation — Springs, when employed to actuate ventilator doors, shall be capable of maintaining full required tension indefinitely. Springs shall not be stressed more than 50% of their rated capacity and shall not be located directly in the air stream, nor exposed to elements.

e.

Location of Fusible Links — A fusible link shall be placed in the cable control system on the underside of the ventilator at or above the roof line or as approved by the Building Official, and shall be so located as not to be affected by the operation of fire-extinguishing systems.

f.

Control — Remote, manual or electrical control shall provide for both opening and closing of the ventilator doors for periodic testing and shall be located at a point on the stage designated by the Building Official. When remote control of ventilator is electrical, power failure shall not affect its instant operation in the event of fire. Hand winches may be employed to facilitate operation of manually controlled ventilators. EDSHcT

2.

Copyright 2010

Gridirons — a.

Gridirons, fly galleries, and pin-rails shall be constructed of incombustible materials and fire protection of steel and iron maybe omitted. Gridirons and fly galleries shall be designed to support a live load of not less than 367 kilograms per sq. meter. Each loft block well shall be designed to support 373 kilograms per linear meter and the head block well shall be designed to support the aggregate weigh of all the loft block wells served. The head block well must be proved with an adequate strong back or lateral brace to offset torque.

b.

The main counterweight sheave beam shall be designed to support a horizontal and vertical uniformly distributed live load sufficient to accommodate the weight imposed by the total number of loft blocks in the gridiron. The sheave blocks shall be designed to accommodate the maximum load for the loft or head blocks served with a safety factor of five (5).

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

268

Copyright 2010

3.

Rooms Accessory to Stage — In a building having a stage, the dressing room sections, workshops, and storerooms shall be located on the stage side of the proscenium wall and shall be separated from each other and from the stage by not less than a One-Hour Fire-Resistive Occupancy Separation.

4.

Proscenium Walls — A stage shall be completely separated from the auditorium by a proscenium wall of not less than two-hour incombustible construction. The proscenium wall shall extend not less than 1.20 meters above the roof over the auditorium. Proscenium walls may have, in addition to the main proscenium openings, one (1) opening at the orchestra pit level and not more than two (2) openings at the stage floor level, each of which shall be not more than 2.00 sq. meters in area. All openings in the proscenium wall of stage shall be protected by a fire assembly having a one and one-half — hour fire-resistive rating. The proscenium opening, which shall be the main opening for viewing performances, shall be provided with a self-closing fire-resistive curtain as specified in the Code.

5.

Stage Floor — The type of construction for stage floors shall depend upon the requirements based on the Type of Occupancy and the corresponding fire-resistive requirements. All parts of the stage floor shall be designed to support not less than 620 kilograms per square meters. Openings through stage floors shall be equipped with tight-fitting trap doors of wood of not less than 50 millimeters nominal thickness.

6.

Platforms — The type of construction for platforms shall depend upon the requirements based on the Type of Occupancy and corresponding fire-resistive requirements. Enclosed platforms shall be provided with one (1) or more ventilators conforming to the requirements of stage ventilators; Except, that the total area shall be equal to 5% of the area of the platform. When more than one (1) ventilator is provided, they shall be so spaced as to provide proper exhaust ventilation. Ventilators shall not be required for enclosed platforms having a floor area of 45.00 sq. meters or less.

7.

Stage Exits — At least one (1) exit not less than 900 millimeters wide shall be provided from each side of the stage opening

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

269

directly or by means of a passageway not less than 900 millimeters in width to a street or exit court. An exit stair not less than 750 millimeters wide shall be provided for egress from each fly gallery. Each tier of dressing rooms shall be provided with at least two (2) means of egress each not less than 750 millimeters wide and all such stairs shall be constructed in accordance with the requirement specified in the Code. The stairs required in this Sub-section need not be enclosed. SECTION 1214. Motion Picture Projection Rooms. — 1.

General Requirements — The provisions of this Section shall apply only where ribbon type motion picture films in excess of 22-millimeter width and electric projection equipment are used. Every motion picture machine using ribbon type film in excess of 22 millimeter width and electric arc projections equipment, together with all electrical devices, rheostats, machines, and all such films present in any Group C, I, or H Occupancy, shall be enclosed in a projection room large enough to permit the operator to walk freely on either side and back of the machine.

2.

Construction — Every projection room shall be of not less than one-hour fire-resistive construction throughout and the walls and ceiling shall be finished with incombustible materials. The ceiling shall be not less than 2.40 meters from the finished floor. The room shall have a floor area of not less than 7.00 sq. meters and 3.50 sq. meters for each additional machine. AcHCED

Copyright 2010

3.

Exit — Every projection room shall have at least two doorways separated by not less than one-third the perimeter of the room, each at least 750 millimeters wide and 2.00 meters high. All entrances to a projection room shall be protected by a self-closing fire assembly having a three-fourth — hour fire-resistive rating. Such doors shall open outward and lead to proper exits as required in the Code and shall not be equipped with any latch. The maximum width of such door shall be 750 millimeters.

4.

Ports and Openings — Ports in projection room walls shall be of three (3) kinds: projection ports; observation ports; and combination ports used for both observation and for stereopticon, spot or floodlight machines.

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

270

a.

Ports Required — There shall be provided for each motion picture projector not more than one (1) projection port, which shall be limited in area to 750 sq. centimeters, and not more than one (1) observation port, which shall be limited in area to 1,300 sq. centimeters. There shall be not more than three (3) combination ports, each of which shall not exceed 750 millimeters by 600 millimeters. Each port opening shall be completely covered with a pane of glass; Except, that when acetate safety film is used, projection ports may be increased in size to an area not to exceed 4,500 sq. centimeters.

b.

Shutters — Each port and every other opening in projection room walls, including, any fresh-air inlets but excluding exit doors and exhaust ducts, shall be provided with a shutter of not less than 2.4 millimeters thick sheet metal or its equivalent large enough to overlap at least 25 millimeters on all sides of such openings. Shutters shall be arranged to slide without binding in guides constructed of material equal to the shutters in strength and fire-resistance. Each shutter shall be equipped with a 74º fusible link, which when fused by heat will cause closure of the shutter by gravity. Shutters of a size greater than 1,300 sq. centimeters shall be equipped with a counter-balance. There shall also be a fusible link located over the upper magazine of each projector, which upon operating, will close all the shutters. In addition, there shall be provided suitable means for manually closing all shutters simultaneously from any projector head and from a point within the projection room near each exit door. Shutters on openings not in use shall be kept closed; Except, that shutters may be omitted when only acetate safety film is used. cITCAa

5.

Ventilation a.

Copyright 2010

Inlet — A fresh-air inlet from the exterior of the building not less than 900 sq. centimeters and protected with wire netting, shall be installed within 50 millimeters of the floor in every projection room, the source of which shall be remote from other outside vents or flues.

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

271

b.

6.

Outlets — Ventilation shall be provided by one (1) or more mechanical exhaust systems which shall draw air from each arc lamp housing to outdoors either directly or through an incombustible flue used for no other purpose. Exhaust capacity shall not be less than 0.50 cu. meter nor more than 1.40 cu. meter per minute for each arc lamp plus 5.60 cu. meters for the room itself. Systems shall be controlled from within the enclosure and shall have pilot lights to indicate operation. The exhaust systems serving the projection room may be extended to cover rooms associated therewith such as rewind rooms. No dampers shall be installed in such exhaust systems. Ventilation of these rooms shall not be connected in any way with ventilating or air-conditioning systems serving other portions of the building. Exhaust ducts shall be of incombustible material and shall either be kept 25 millimeters from combustible material or covered with 10 millimeters of incombustible heat-insulating material.

Regulation of Equipment — All shelves, fixtures, and fixed equipment in a projection room shall be constructed of incombustible materials. All films not in actual use shall be stored in metal cabinets having individual compartments for reels or shall be in generally accepted shipping containers. No solder shall be used In the construction of such cabinets.

SECTION 1215. Lathing, Plastering, and Installation of Wall Boards. — The installation of lath, plaster and gypsum wall board shall conform to the fire-resistive rating requirements and the type of construction of building. RULE XIII Electrical and Mechanical Regulations SECTION 1301. Electrical Regulations. — All electrical systems, equipment and installations mentioned in the Code shall conform to the provisions of the Philippine Electrical Code Part 1 (PEC-1) and Part 2 (PEC-2), as adopted by the Board of Electrical Engineering pursuant to Republic Act 7920, otherwise known as the Philippine Electrical Engineering Law. ECSaAc

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

272

1.

Overhead Service Entrance In Subdivisions, Housing Projects, Commercial and Industrial Buildings, overhead transmission and distribution voltages are required to supply power source including transformers, poles and supporting structures.

2.

Attachments on and Clearances from Buildings a.

An Attachment Plan approved by professional electrical engineer shall cover power lines and cables, transformers and other electrical equipment installed on or in buildings and shall be submitted to the local Building Official. DaIAcC

b.

Where building/s exceed 15.00 meters in height, overhead lines shall be arranged where practicable so that clear space or zone at least 1.80 meters (horizontal) will be left adjacent to the building or beginning not over 2.45 meters (horizontal) from the building, to facilitate the raising of ladders where necessary for fire fighting. EXCEPTION: This requirement does not apply where it is the rule of the local fire department to exclude the use of ladders in alleys or other restricted places, which are generally occupied by supply lines.

3.

Open Supply Conductors Attached to Buildings Where the permanent attachment of open supply conductors to any class of buildings is necessary for service entrance, such conductors shall meet the following requirements: a.

Conductors of more than 300 volts to ground shall not be carried along or near the surface of the building unless they are guarded or made inaccessible. DTAHSI

b.

Copyright 2010

To promote safety to the general public and to employees not authorized to approach conductors and other current-carrying parts of electric supply lines, such parts shall be arranged so as to provide adequate clearance from the ground or other space generally accessible, or shall be provided with guards so as to isolate persons

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

273

effectively from accidental contact.

4.

c.

Ungrounded service conduits, metal fixtures and similar noncurrent-carrying parts, if located in urban districts and where liable to become charged to more than 300 volts to ground, shall be isolated or guarded so as not to be exposed to accidental contact by unauthorized persons. As an alternative to isolation or guarding noncurrent-carrying parts shall be solidly or effectively grounded.

d.

Service drops passing over a roof shall be securely supported by substantial structures. Where practicable, such supports shall be independent of the building.

Conductors Passing By or Over Buildings a.

Unguarded or accessible supply conductors carrying voltages in excess of 300 volts may be either beside or over buildings. The vertical or horizontal clearance to any buildings or its attachments (balconies, platforms, etc.) shall be as listed in Table XIII.1. The horizontal clearance governs above the roof level to the point where the diagonal equals the vertical clearance requirements. This Rule should not be interpreted as restricting the installation of a trolley contact conductor over the approximate centerline of the track it serves. (Figure XIII.1.)

b.

Supply conductors of 300 volts or more, when placed near enough to windows, verandas, fire escapes, or other ordinarily accessible places, shall be properly guarded by grounded conduit and barriers.

c.

Where the required clearances cannot be obtained, supply conductors shall be grouped or bundled and supported by grounded messenger wires. CIETDc

5.

Clearance of Service Drops a.

Copyright 2010

Service drop conductors shall not be readily accessible and when not in excess of 600 volts, shall conform to the following:

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

274

i. Conductors shall have a clearance of not less than 2.50 meters from the highest point of roofs over which they pass with the following exceptions: (a) Where the voltage between conductors does not exceed 300 volts and the roof has a slope of not less than 100 millimeters in 300 millimeters, the clearance may not be less than 1.00 meter. (b) Service drop conductors of 300 volts or less which do not pass over other than a maximum of 1.20 meters of the overhang portion of the roof for the purpose of terminating at a through-the-roof service raceway or approved support may be maintained at a minimum of 500 millimeters from any portion of the roof over which they pass. b.

Conductors shall have a clearance of not less than 3.00 meters from the ground or from any platform or projection from which they might be reached.

c.

Conductors shall have a horizontal clearance of not less than 1.00 meter from windows, doors, porches, fire escapes, or similar locations and shall be run less than 1.00 meter above the top level of a window or opening.

d.

Service drop of conductors, when crossing a street, shall have a clearance of not less than 5.50 meters from the crown of the street or sidewalk over which it passes; and shall have a minimum clearance of 3.00 meters above ground at its point of attachment to the building or pedestal.

e.

No parts of swimming and wading pools shall be placed under existing service drop conductors or any other overhead wiring; nor shall such wiring be installed above the following: i. Swimming and wading pools and the area extending 3.00 meters outward horizontally from the inside of the walls of the pool; cCSDaI

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

275

ii.

Diving structures;

iii.

Observation stands, towers or platforms.

TABLE XIII.1. Clearance of Wires, Conductors, Cables and Unguarded Rigid Energized Parts Adjacent but not Attached to Buildings and Other Installations Except Bridges Clearance of

Insulated Communication conductors and cables; messengers; surge protection wires; grounded guys; neutral conductors

1.

Buildings a. Horizontal (1) To walls, projection and guarded windows (2) To unguarded windows (3) To balconies an areas readily

Supply Unguarded rigid cables of energized parts, 0 to 750 V; 0 to 750 V; V non-insulated communication conductors

(mm)

Supply cables over 750 V; open supply conductors, 0 to 750 V

Open supply conductors, over 750 V to 22 kV

Unguarded rigid energized parts, over 750 V to 22 kV

(mm)

(mm)

(mm)

(mm)

1400

1500

1500

1700

2300

2000

1400

1500

150D

1700

2300

2000

1400

1500

1500

1700

2300

2000

900

1070

3000

3200

3600

3600

3200

3400

3400

3500

4100

4000

3200

3400

3400

3500

4100

4000

4700

4900

4900

5000

5600

5500

accessible b.

Vertical (1) Over or Under roofs or projections not readily accessible to pedestrians (2) Over or under balconies and roofs readily accessible to pedestrians (3) Over roofs accessible to vehicles but not subject to truck traffic (4) Over roofs accessible to truck traffic

2.

Signs, chimneys, billboards, radio and television antennas, and other installations

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

276

not classified as buildings or bridges a.

Horizontal

900

1070

1500

1700

2300

2000

b.

Vertical

900

1070

1700

1800

2450

2300

over or under

CLEARANCE DIAGRAM FOR BUILDING 6.

Wiring Methods Service entrance conductors extending along the exterior or entering buildings or other structures shall be installed in rigid steel conduit or

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

277

concrete encased plastic conduit from point of service drop to meter base and from meter base to the disconnecting equipment. However, where the service entrance conductors are protected by approved fuses or breakers at their terminals (immediately after the service drop or lateral) they may be installed in any of the recognized wiring methods as provided by PEC-1.

7.

a.

Abandoned lines and/or portions of lines no longer required to provide service shall be removed.

b.

Power pole, lines, service drop and other line equipment shall be free from any attachment for antennas, signs, streamers and the like.

Transformers a.

Oil-insulated transformers rated more than 15 kV between conductors shall be installed inside a transformer vault.

b.

Dry-type and other transformers with non-flammable insulation shall be installed in a transformer room.

c.

Transformers shall be guarded as follows: i.

Appropriate provisions shall be made to minimize the possibility of damage to transformers from external causes where the transformers are located exposed to physical damage.

ii.

Dry-type transformers shall be provided with a noncombustible moisture resistant case or enclosure which will provide reasonable protection against accidental insertion of foreign objects. DHIaTS

8.

Copyright 2010

iii.

The transformer installation shall conform to the provisions for guarding of live parts in PEC-1.

iv.

The operating voltage of exposed live parts of transformer installations shall be indicated by signs or visible markings on the equipment or structures.

Provisions for Transformer Vault

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

278

9.

a.

A transformer vault when required, shall be constructed in accordance with PEC-1 latest edition.

b.

Transformers and transformer vaults shall be accessible only to qualified personnel for inspection and maintenance.

c.

Adequate ventilation transformer vault.

shall

be

provided

for

the

Capacitor a.

This applies to installation of capacitors on electric circuits in buildings. EXCEPTION:

1. Capacitors that are component of other apparatus shall conform to the requirements for such apparatus. 2. Capacitors in hazardous locations shall comply with additional requirements as prescribed in PEC-1.

10.

b.

Installation of capacitors in which any single unit contains more than 11 liters of flammable liquid shall be in a vault or outdoor fence enclosures complying with PEC-1.

c.

Capacitors shall be protected from physical damage by location or by suitable fences, barriers or other enclosures.

d.

Capacitors shall be provided with noncombustible cases and supports.

Emergency Power Systems a.

Shall provide electric power for the safety to life and property when normal electric power supply is interrupted.

b.

Shall have adequate capacity for the operation of the emergency load. DASCIc

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

279

c.

11.

Electrical Room a.

12.

An adequate space or area shall be provided at load centers where panel boards, breakers, switchgears and other electrical equipment are installed.

Service Equipment a.

13.

For hospitals, the transition time to transfer power supply from the instant of interruption of normal power supply to the emergency supply shall not exceed 10 seconds.

An adequate space or area shall be provided for the service equipment that shall be located in a readily accessible area, either inside or the outside walls of the building.

Metering Facilities a.

Metering Vault, when required for primary service, shall be provided with natural or artificial ventilation.

b.

Metering space shall be provided for single metering or multi-metering centers for secondary service.

SECTION 1302. Mechanical Regulations. — 1.

All mechanical systems, equipment and installations mentioned in the Code shall conform to the provisions of the Philippine Mechanical Code, as adopted by the Board of Mechanical Engineering pursuant to RA 8495 as amended, otherwise known as the Philippine Mechanical Engineering Law.

2.

Guarding of Moving and Dangerous Parts All prime movers, machines and machine parts, power transmission equipment shall be so guarded, shielded, fenced or enclosed to protect any person against exposure to or accidental contact with dangerous moving parts.

3.

Cranes a.

Copyright 2010

Adequate means like ladders, stairs or platforms shall be provided for cranes having revolving cabs or machine

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

280

houses, to permit the operator to enter or leave the crane cab and reach the ground safely, irrespective of its position. If a step-over is provided, the gap must not exceed 300 millimeters.

4.

b.

A gong or other effective warning device shall be mounted on each cage or cab.

c.

Temporary crane operation without warning device may be allowed provided there is a flagman whose sole duty is to warn those in the path of the crane or its load.

d.

The maximum rated load of all cranes shall be plainly marked on each side of the crane. If the crane has more than one hoisting unit, each hoist shall have marked on it or its load block, its rated capacity clearly legible from the ground or floor.

Hoists a.

Operating control shall be plainly marked to indicate the direction of travel and provided with an effective warning device.

b.

Each hoist designed to lift its load vertically shall have its rated load legibly marked on the hoist or load block or at some easily visible space. ACTIcS

5.

c.

A stop, which shall operate automatically, shall be provided at each switch, dead end rail or turntable to prevent the trolley running off when the switch is open.

d.

Each electric hoist motor shall be provided with electrically or mechanically operated brake so arranged that the brake will be applied automatically when the power is cut off from the hoist.

Elevators Elevators shall be installed in all private and public buildings for public use accessible to disabled persons, pursuant to the objectives of Batas Pambansa Bilang 344 (Accessibility Law). a.

Copyright 2010

Hoistway for elevators shall be substantially enclosed

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

281

throughout their height, with no openings allowed except for necessary doors, windows or skylights. b.

Ropes, wires or pipes shall not be installed in hoistways, except when necessary for the operation of the elevators.

c.

Hoistway pits shall be of such depth that when the car rests on the fully compressed buffers, a clearance of not less than 600 millimeters remains between the underside of the car and the bottom of the pit. IASTDE

d.

When four (4) or more elevators serve all or the same portion of a building, they shall be located in not less than two (2) hoistways and in no case shall more than four (4) elevators be located in any one hoistway.

e.

Where a machine room or penthouse is provided at the top of a hoistway, it shall be constructed with sufficient room for repair and inspection. Access shall be by means of an iron ladder or stairs when the room is more than 600 millimeters above the adjacent floor or roof surface. The angle of inclination of such ladder or stairs shall not exceed 60º from the horizontal. This room shall not be used as living quarters or depository of other materials and shall be provided with adequate ventilation.

f.

Minimum number of hoisting ropes shall be three (3) for traction elevators and two (2) for drum type elevators.

g.

The minimum diameter of hoisting and counterweight ropes shall be 30 millimeters.

h.

Elevators shall be provided with Fall-Free Safety Device, over-load switch and reverse polarity relay. CSHEca

i.

6.

Escalators a.

Copyright 2010

In apartments or residential condominiums of five (5) storeys or more, at least one (1) passenger elevator shall be kept on twenty-four (24) hour constant service.

The angle of inclination of an escalator shall not exceed 30º from the horizontal.

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

282

7.

b.

The width between balustrades shall not be less than 560 millimeters nor more than 1.20 meters. This width shall not exceed the width of the steps by more than 330 millimeters.

c.

Solid balustrades of incombustible material shall be provided on each side of the moving steps. If made of glass, it shall be of tempered type glass.

d.

The rated speed, measured along the angle of inclination, shall be not more than 38 meters per minute.

Boilers and Pressure Vessels a.

Location of Boilers i.

Boilers may be located inside buildings provided that the boiler room is of reinforced concrete or masonry and that the boiler room shall not be used for any other purpose. No part of the boiler shall be closer than 1.00 meter from any wall and shall have at least two (2) separate exits.

ii.

In case the main building is not made up of fire resistive materials, boilers shall be located outside the building at a distance of not less than 3.00 meters from the outside wall of the main building and the building housing the boiler shall be made up of fire-resistive materials.

b.

Smokestacks, whether self-supporting or guyed, shall be of sufficient capacity to handle fuel gases, shall be able to withstand a wind load of 175 kilometers per hour and shall rise at least 5.00 meters above the eaves of any building within a radius of 50.00 meters.

c.

Manufacturers/assemblers of boilers/pressure vessels/pressurized water heaters shall stamp each vessel on the front head or on any other suitable location with the name of the manufacturer, serial number, year of manufacture maximum allowable working pressure, heating surface in sq. meters, and thickness of shell. SacDIE

d.

Copyright 2010

Boilers of more than 46.00 sq. meters heating surface shall each be provided with two (2) means of feeding

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

283

water, one (1) steam driven and one (1) electrically driven, or one (1) pump and one (1) injector. e.

Two (2) check valves shall be provided between any feed pump and the boiler in addition to the regular shut-off valve.

f.

Where two (2) or more boilers are connected in parallel, each steam outlet shall be provided with a non-return valve and a shut-off valve.

g.

In no case shall the maximum pressure of an existing boiler be increased to a greater pressure than would be allowed for a new boiler of same construction.

h.

Each boiler shall have at least one (1) safety valve. For boilers having more than 46.00 sq. meters of water heating surface or a generating capacity exceeding 910 kilograms per hour, two (2) or more safety valves shall be required.

i.

Each boiler shall have a steam gauge, with a dial range of not less than one and one-half times and not more than twice the maximum allowable working pressure. It may be connected to the steam space or to the steam connection to the water column. TaCDIc

Copyright 2010

j.

Repairs/replacements on any parts shall comply with the applicable section on New Installation of Boilers/Pressure Vessels of the Philippine Mechanical Code.

k.

Upon the completion of the installation, the Building Official shall conduct an inspection and test, and if found complying with requirements, a certificate of operation for a period not exceeding one (1) year shall be issued after payment of the required inspection fees.

l.

After a permit has been granted to install a boiler/pressure vessel/pressurized water heater upon payment of the installation fees therefore, it shall be the duty of the Building Official to make periodic inspection of the installation to determine compliance with the

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

284

approved plans and specifications. m.

The Building Official shall notify the owner in writing of the intended date of the annual inspection at least fifteen (15) days in advance but not to exceed thirty (30) days from the intended date of inspection. AEDHST

n.

8.

The owner/user shall prepare the boiler(s) for inspection and provide all labor and equipment required during said inspection.

Refrigeration and Air Conditioning a.

The effective temperature and relative humidity of the air to be used for comfortable cooling shall be maintained at 20º Celsius to 24º Celsius and 50% to 60%, respectively, with 4.60 to 7.60 meters per minute air movement within the living zone.

b.

Water from evaporators, condensers and other machinery shall be properly collected into a suitable water or drainage system.

c.

Ducts shall be constructed entirely of noncombustible materials such as steel, iron, aluminum or other approved materials. Only fire retardant lining shall be used on the inside of ducts.

d.

Access doors shall be provided at all automatic dampers, fire dampers, thermostats and other apparatus requiring service and inspection in the duct system. caITAC

Copyright 2010

e.

Where ducts pass thru walls, floors or partitions, the space around the duct shall be sealed with fire resistant material equivalent to that of the wall, floor or partition, to prevent the passage of flame or smoke.

f.

When ducts or their outlets or inlets pass through firewalls, they shall be provided with automatic fire dampers that automatically close on both sides of the firewall through which they pass.

g.

Fire doors and fire dampers shall be arranged to close automatically and remain tightly closed, upon the

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

285

operation of a fusible link or other approved heat actuated device, located where readily affected by an abnormal rise of temperature in the duct.

9.

h.

Each refrigerating system shall be provided with a legible metal sign permanently attached and easily noticeable, indicating thereon the name of manufacturer or installer, kind and total number of kilograms of refrigerant contained in the system and applied field test pressure applied.

i.

In refrigerating plants of more than 45 kilograms, refrigerant, masks and helmets shall be used. These shall be kept in a suitable cabinet outside the machine room when not in use.

j.

Not more than 140 kilograms of refrigerant in approved containers shall be stored in a machine room at any given time.

k.

Where ammonia is used, the discharge may be into tank of water, which shall be used for no other purpose except ammonia absorption. At least 1 liter of water shall be provided for every 120 gallons of ammonia in the system.

l.

In a refrigerating system containing more than 9 kilograms, stop valves shall be installed in inlets and outlets of compressors, outlets of liquid receivers, and in liquid and suction branch headers.

m.

Window type air conditioners shall be provided with drainpipe or plastic tubing for discharging condensate water into a suitable container or discharge line.

n.

Window type air conditioners shall be provided with exhaust ducts if the exhaust is discharged into corridors/hallways/arcades/sidewalks, etc., and shall be installed at not less than 2.10 meters above the floor level.

Water Pumping for Buildings/Structures a.

Copyright 2010

Installation

CD Technologies Asia, Inc.

of

pumping

Philippine Laws Premium Edition 2009

equipment

to

supply 286

buildings/structures directly from existing water supply system shall not be allowed. An underground water tank or cistern must be filled by gravity flow from the water supply system, from where pumps can be installed. b.

To maintain water pressure in all floors of a building/structure, the following systems may be used: i. Overhead tank supply — may be installed above the roof supported by the building/structure or on a separate tower. acTDCI

(a) Water tanks shall be provided with a vent and an overflow pipe leading to a storm drain and shall be fully covered. ii. Pneumatic tank — an unfired pressure vessel, initially full of air, into which water from mains is pumped. (a) A suitable pressure switch shall stop the pump when pressure required is attained. (b) Tanks shall be designed for twice the maximum total dynamic pressure required. (c) An air volume control device shall be installed to maintain correct air volume inside the tank. 10.

Pipings for Fuel, Gas and Steam a.

Piping shall, as much as possible, run parallel to building walls.

b.

Grouped piping shall be supported on racks, on either horizontal or vertical planes. IHEaAc

Copyright 2010

c.

Piping on racks shall have sufficient space for pipe or chain wrenches so that any single line can be altered/repaired/replaced without disturbing the rest.

d.

Piping 100 millimeters in diameter and above shall be flanged. Smaller sized pipes may be screwed.

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

287

11.

Copyright 2010

e.

Piping subjected to varying temperatures shall be provided with expansion joints.

f.

Galvanized piping shall not be used for steam.

g.

Piping carrying steam, hot water or hot liquids shall not be embedded in concrete walls or floors and shall be properly insulated.

h.

Piping carrying propane, butane and other gas which are heavier than air, shall be provided with automatic shut-off devices. The automatic shut-off device is most effective if provided to each burner before the flexible connection.

Identification of piping by color and tag shall be as follows: Material Piped

Pipe Color

Acetylene Acid Air-High pressure Air-Low Pressure Ammonia Argon-Low Pressure Blast Furnace Glass Carbon Dioxide Gasoline Grease Helium-Low Pressure Hydrogen Nitrogen-Low Pressure Oxygen Oil Steam-High Pressure Steam-Low Pressure Tar Producer Gas Liquid Petroleum Gas Vacuum-High Water-Boiler Feed Water-Cold Water-Distilled Water (Fire Service)

Orange Yellow Yellow Green Yellow Green Orange Red Orange Orange Green Orange Green Orange Orange Yellow Yellow Orange Orange Orange Orange Yellow Green Green Red

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

Pipe Identification Acetylene Acid H.P. Air L.P. Air Ammonia L.P. Argon B.F. Gas Carbon Dioxide Gasoline Grease L.P. Helium Hydrogen L.P.-Nitrogen Oxygen Oil H.P. Steam L.P. Steam Tar Producer Gas L.P. Gas High Vacuum Boiler Feed Water Cold Water Distilled Water Fire Service Water 288

Water-Hot Water-Low-Pressure (Excl. of fire Service) Water-High Pressure (Excl. of Fire service) Water-Treated Oil and Water (For hydraulic system) Oil and Water (For hydraulic system)

Yellow

Hot Water

Green

L.P. Water

Yellow Green

H.P. Water Treated Water

Green

Oil and Water

Orange

Oil and Water

RULE XIV Photographic and X-Ray Films SECTION 1401. Storage and Handling. — 1.

2.

Storage rooms of unexposed photographic and x-ray films shall be provided with automatic fire extinguishing systems in the following cases: a.

When unexposed films in generally accepted safety shipping containers exceed the aggregate of 14.00 cu. meters;

b.

Where shelving used for storage of individual packages not in said shipping containers exceeds 1.40 cu. meters in capacity; and

c.

Storage is not in generally accepted safety shipping containers in any section not exceeding 14.00 cu. meters.

Film negatives in storage or in process of handling shall be kept in heavy Manila envelopes, not exceeding twelve (12) films to an envelope. Expanding envelopes shall not be used. AECDHS

Copyright 2010

3.

Film negatives shall be kept in properly insulated vented cabinets, vented storage vaults or outside storage houses. Not more than 110 kilograms shall be stored in any single cabinet. Where the film stored exceeds 450 kilograms, it shall be in vented storage vaults or in a detached structure or roof vault. Door openings in vaults shall be of four-hour fire-resistive construction and shall be kept closed except when in use.

4.

Only incandescent electric light shall be permitted; protected

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

289

with substantial wire guards or vapor proof globes or both. Portable lights on extension cords are prohibited. Conspicuous "NO SMOKING" signs shall be posted. 5.

No films shall be stored within 600 millimeters of steam pipes, chimneys, or other sources of heat.

6.

There shall be first aid provisions of types using water or water solutions. Discarded films shall be stored and handled in the same manner as other films until removed from the premises.

SECTION 1402. Classes of Film Exempted. — 1.

The provisions of this Section do not apply to the following: film for amateur photographic use in original packages of "roll" and "film pack" films in quantities of less than 1.40 cu. meters; safety film; dental X-ray film; establishments manufacturing photographic films and their storage incidental thereto; and films stored or being used in standard motion picture booths.

2.

Safety photographic X-ray film may be identified by the marking on the edge of the film.

SECTION 1403. Fire Extinguishing System. — Unless otherwise provided in the Code, all fire extinguishing systems when so required shall be of a type, specifications, and methods of installation as prescribed in accordance with the requirements of the Secretary. RULE XV Prefabricated Construction SECTION 1501. Prefabricated Assembly. — 1.

Prefabricated assembly is a structural unit, the integral parts of which have been built-up or assembled prior to incorporation in the building. It shall be made of pre-cast concrete, various metal components, unplasticized polyvinyl chloride (uPVC) or other construction materials acceptable to the architect/engineer. ISCaDH

2.

Copyright 2010

To determine the structural adequacy, durability, soundness, weather and fire resistance of pre-fabricated assemblies, they shall pass the special tests conducted by any accredited material

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

290

testing laboratories. 3.

Every device or system to connect prefabricated assemblies shall be capable of developing the strength of the different members as an integral structure. Except, in the case of members forming part of a structural frame as specified in the Code and this IRB.

4.

Anchorages and connections between members and the supporting elements of the structure or walls shall be capable of withstanding all probable external and internal forces or other conditions for a structurally adequate construction.

5.

In structural design, proper allowances shall be made for any material to be displayed or removed for the installation of pipes, conduits, or other equipment. ATcEDS

6.

Metal and uPVC prefabricated assembly shall be adequately provided with anchorage and connectors.

7.

Placement of prefabricated assemblies shall be inspected to determine compliance with the Code.

8.

During the placement of the prefabricated assembly, a safety engineer shall be required at the site. RULE XVI Plastics

SECTION 1601. Approved Plastics. — Approved plastic materials shall be those which have a flame-spread rating of two hundred twenty five (225) or less and a smoke density not greater than that obtained from the burning of untreated wood under similar conditions when tested in accordance with generally accepted engineering practices, The products of combustion shall be no more toxic than the burning of untreated wood under similar conditions. SECTION 1602. Installation. — 1.

Copyright 2010

Structural Requirements — All plastic materials shall be of adequate strength and durability to withstand the prescribed design loads. Sufficient and substantial technical data shall be

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

291

submitted to establish stresses, maximum unsupported spans, and such other information as may be deemed necessary for the various thicknesses and forms used. 2.

Fastenings — Fastenings shall be adequate to withstand design loads and internal and external stresses required of the assembly. Proper allowances of plastic materials in conjunction with other materials with which it is assembled or integrated shall be provided.

SECTION 1603. Glazing of Openings. — 1.

The location of doors, sashes and framed openings glazed or equipped with approved plastics at the exterior walls of a building shall be so arranged that in case of fire, the occupants may use such openings to escape from the building to a place of safety. The travel distance from any point of the building towards the location of such openings should not be over 45.00 meters in any place of assembly for spaces not protected by automatic fire suppression and 60.00 meters in areas so protected. IDEScC

Copyright 2010

2.

Openings glazed with approved plastics at the ground floor shall be so located such that it shall open directly to a street or into an exit court. Such openings at the upper floor shall be so located at a horizontal distance not less than 3.00 meters from the enclosed stairway, outside stairway or exit passageway leading to a street or into an exit court.

3.

The use of plastic doors, sashes and framings of openings for Group A to I Occupancies may be allowed except for entrance doors and exit doors which should be of materials other than plastics permitted by the Code.

4.

The size of openings glazed with approved plastics shall have a minimum dimension where one person could pass through or 600 millimeters square.

5.

The maximum size of such openings depends upon the structural strength and the fastening adequacy requirements of approved plastics being used.

6.

The spacing between openings glazed with approved plastics

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

292

shall have a minimum distance such that the materials used in between can withstand the vertical and lateral forces within the influence of such openings. The minimum distance shall be 2.00 meters for all spans. SECTION 1604. Skylights. — 1.

2.

General — Approved plastics may be used in skylights installed on roofs of Types I, II or III Constructions and all buildings in these categories shall be equipped with an approved automatic fire-extinguishing system in Groups A, B, C, E, F, J, H-3 and H-4 Occupancies; Except, that: a.

Approved plastics may be used in any type of construction or occupancy as a fire venting system when approved by the Building Official.

b.

Plastics may be used in approved skylights in Type II one-hour fire-resistive construction which are located 300 millimeters or more above the lower flange of the ceiling. The walls of the skylight well shall be no less fire-resistive than the adjacent ceiling.

c.

Where a fire-resistive ceiling is not required in one-storey buildings, approved plastics may be used in skylights.

Installation Requirements a.

Except in Group A Occupancies, no skylight shall be installed within 3.00 meters of a property line. IHaCDE

3.

Copyright 2010

b.

The edges of dome-type skylights shall be properly flashed.

c.

Plastic skylights shall be separated from each other by at least 2.50 meters laterally and 3.00 meters along the slope of the roof.

Allowable areas — The area of individual plastic skylights shall not exceed 10.00 square meters. The total aggregate area of plastics used in skylights, monitors, and sawtooth glazing shall not exceed 20% of the floor area of the room or occupancy sheltered.

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

293

4.

Curb Requirements — Plastic skylights in roofs having a slope of less than 1 in 3 shall have a 100 millimeters high curb. The curb may be omitted where a wire screen not smaller than No. 12 U.S. gauge with a mesh not larger than 25 millimeters is provided immediately below the skylight. The screen shall be substantially mounted below the skylight.

SECTION 1605. Light-Transmitting Panels in Monitors and Sawtooth Roofs. — 1.

General — Where a fire-resistive rating is not required for the roof structure, and in all buildings provided with an approved automatic fire-extinguishing system, approved plastics may be used with or without sash as the light-transmitting medium in monitors and sawtooth; Except, that plastics used in monitors or sawtooth roofs of Type II Construction shall be of materials appropriate to be used according to flame-spread characteristics.

2.

Allowable Areas — The area of individual plastic glazing used in monitors and sawtooth glazing shall not exceed 15.00 square meters. The total aggregate area of plastics used in skylights, monitors, and sawtooth glazing shall not exceed 20% of the floor area of the room or occupancy sheltered.

3.

Area Separation — The area of such plastic panels shall be separated from each other by a section of incombustible material or by a section of the roofing material of the structure not less than 1.50 meters in length. The lower edge of the plastic material shall be at least 150 millimeters above the surface of the adjoining roof surface.

SECTION 1606. Plastic Light Diffusers in Ceilings. —

Copyright 2010

1.

General — Ceiling light diffusers having an area greater than 10% of any 10.00 sq. meters of room area shall be of approved plastics conforming to the requirements specified in the Code.

2.

Installation — Plastic light diffusers shall be installed in such a manner that they will not readily become detached when subjected to room temperature of 80ºC for 15 minutes, Except, for plastic light diffusers which are installed in the first floor area of Group C Occupancies having egress directly to the

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

294

exterior of the building; and plastic light diffusers which are located between an approved automatic Fire-extinguishing system and the area to be protected other than public corridors for Group A, B, C, D, E, G, H, and I Occupancies if tests required by the Secretary have established that such installation will not interfere with the efficient operation of such automatic fire-extinguishing systems. SECTION 1607. Partitions. — Where partitions are not required to be of fire-resistive or incombustible construction, approved plastics conforming to the requirements specified in the Code may be used. SECTION 1808. Exterior Veneer. — 1.

General — Exterior veneer may be of approved plastic materials, and shall conform to the provisions of this Section.

2.

Height — Plastic veneer shall not be attached to any exterior wall above the first storey; Provided, that plastic veneer may be attached to exterior walls above the first storey of buildings located outside of highly restrictive Fire Zones; Provided, further that the height of veneer is not in excess of 10.00 meters above the adjacent grade of elevation.

3.

Area — Sections of plastic veneer shall not exceed 15.00 sq. meters in area, Except, that in less restrictive Fire Zones, the area may be increased by 50%.

4.

Separation — Sections of plastic veneer shall be separated by a minimum of 1.20 meters vertically and 600 millimeters horizontally.

SECTION 1609. Awnings and Canopies. —

Copyright 2010

1.

Plastic materials appropriate for use according to Flame Spread characteristics may be utilized in awnings and canopies, provided such awnings and canopies are constructed in accordance with provisions governing projections and appendages as specified in the Code.

2.

Approved plastics may be used in awnings where untreated canvass is permitted.

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

295

3.

Approved plastics may be used in lieu of plain glass in greenhouses in less restrictive Fire Zones. RULE XVII Sheet Metal Paint Spray Booths

SECTION 1701. Sheet Metal Paint Spray Booth. — 1.

Paint spray booths shall be constructed of steel of not less than No. 18 U.S. gauge in thickness and shall be designed in accordance with the Code.

2.

The area of a paint spray booth shall not exceed 150 sq. meters nor 10% of the basic area permitted for the major use of the building according to its Occupancy Group.

3.

The floor of the spray booth and operator's working area, if combustible, shall be covered with noncombustible, non sparkling material of such character as to facilitate the safe cleaning and removal of residue. SDATEc

4.

Paint spray booths shall be designed to permit the free passage of exhaust air from all parts of the interior and all interior surfaces shall be smooth and continuous without outstanding edges.

SECTION 1702. Fire Protection. — 1.

Every spray booth having an open front elevation larger than 1.00 sq. meters and which is not equipped with doors, shall have a fire curtain or metal deflector not less than 100 millimeters deep installed at the upper outer edge of the booth opening.

2.

Each paint spray booth shall be separated from other operations by not less than 91 centimeters, or by a greater distance, or by such partition or wall as the Local Fire Service Marshall may require.

SECTION 1703. Light. — 1.

Copyright 2010

Paint spray booths shall be illuminated through hammered wire or heat-treated glass panels. The glass panels shall be located in

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

296

such a manner as to reduce the hazard of ignition caused by paint spray deposit. 2.

When spraying areas are illuminated through glass panels or other transparent materials, only light units shall be used as source of illumination.

3.

Panels shall effectively isolate the spraying area from the area in which the lighting unit is located and shall be of noncombustible material or such a nature or so protected that breakage will be unlikely.

4.

Panels shall be arranged so that normal accumulations of residue on the exposed surface of the panel will not be raised to a dangerous temperature by radiation or conduction from the source of illumination.

SECTION 1704. Ventilation. — 1.

Mechanical ventilation shall be provided direct to the exterior of the building. The mechanical exhaust system shall be designed to move the air through any portion of the paint spray area at the rate of not less than 30.00 lineal meters per minute.

2.

The blades of exhaust fans shall be constructed of non-ferrous material and shall be mounted in such a manner as to prevent contact with the exhaust duct.

3.

The motor shall not be mounted in the spray booth or the duct system and belts shall be enclosed where they enter the booth or duct system. EHIcaT

4.

The discharge point for ducts in a paint spray booth shall be not less than 2.00 meters from the adjoining combustible construction nor less than 8.00 meters from adjoining exterior wall openings; except, that the discharge point for exhaust ducts is not regulated in a waterwash spray booth. RULE XVIII Glass and Glazing

SECTION 1801. General Requirements. —

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

297

1.

This Rule shall apply to exterior glass and glazing in all Uses/Occupancies except Groups A, B and J Occupancies not over three (3) storeys in height, and to interior and exterior glass and glazing in all occupancies subject to human impact.

2.

Standards for glass and glazing materials shall conform to the provision on glass dimensional tolerance, breaking stress level, and design safety factors. HcTSDa

3.

Each light (glass panel) shall bear the manufacturer's label designating the type and thickness of glass.

4.

Each light with special performance characteristics such as laminated, heat strengthened, fully tempered or insulated, shall bear the manufacturer's identification showing the special characteristics and thickness by etching or other permanent identification that shall be visible after the glass is glazed.

5.

Appropriate measures shall be provided to deter persons walking into fixed glass panels where the floor contiguous thereto on to both sides is approximately the same level.

6.

Glass panels not adjacent to wall openings may be made obvious by horizontal bars at guardrail height, a 450 millimeters opaque bulkhead, distinctive glass such as etched or translucent for guardrail height, fixed flower bins or other appropriate construction arrangement.

SECTION 1802. Area Limitation. — 1.

Exterior glass and glazing shall be capable of safely withstanding the load due to wind pressure for various height zones above ground acting inward or outward. The area of individual light shall not be more than the maximum allowable area of glass according to the wind load multiplied by the appropriate adjustment factor. cIHCST

Copyright 2010

2.

Glass panels which are more than 600 millimeters in width and 180 millimeters or more in height adjacent to wall opening shall be safety glass unless a bulkhead of opaque materials not less than 450 millimeters high is provided.

3.

The table provided below shall govern the glass area limitation

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

298

for use in large area along shopping malls, commercial buildings, theaters, offices, institutional public buildings and factories other than Group A, B and J Occupancies. THICKNESS (millimeter) 8 10 12 15

WIDTH (meter) 1.10 and below 2.25 and below 3.00 and below Over 3.00

LENGTH (meter) 1.10 and below 2.25 and below 3.00 and below Over 3.00

SECTION 1803. Glazing. — Glass firmly supported on all four (4) edges shall be glazed with minimum laps and edge clearances in accordance with Section 1801 paragraph (2), Provided, that glass edge clearance in fixed openings shall be not less than what is required for wind and earthquake drift. For glass not firmly supported on all four (4) edges and design shall be submitted for approval of the Building Official. Glass supports shall be considered firm when deflection of the support at design load does not exceed 1/175 of the span. SECTION 1804. Louvered Windows. — Regular plate, sheet, or patterned glass in jalousies and louvered windows shall not be thinner than 5.6 millimeters minimal and shall not be longer than 1.20 meters. Exposed glass edges shall be smooth. SECTION 1805. Impact. — Frameless glass doors, glass in doors, fixed glass panels, and similar glazed openings which may be subject to accidental human impact shall conform with the requirements provided under Section 1802 on impact loads of glass; Except in the following cases:

Copyright 2010

1.

Bathtub and shower enclosures shall be constructed from approved shatter-resistant materials, such as: wire-reinforced glass not less than 5.6 millimeters thick; fully tempered glass not less than 4.8 millimeters thick; or laminated safety glass not less than 6.4 millimeters thick.

2.

Glass lights located not less than 450 millimeters above the adjacent finished floor or walking surface.

3.

Glass lights when the least dimension is not greater than 450

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

299

millimeters. 4. Glass lights 1.50 sq. meters or less in area. RULE XIX The Use of Computers SECTION 1901. General Rule. — The use of computer for all or any part of the design of buildings under the Code is permitted provided that all programs to be used are documented. SECTION 1902. Program Documentation. — 1.

Documenting a program under the Code consists of filing with the OBO a reference to a publication or publications accessible to him where the detailed description of the program or a brief statement of the theoretical background of the program including a description of the algorithms used are found.

2.

The software name, version number and the company that developed the program and its address shall be provided as part of the program documentation.

SECTION 1903. Submission of Computer-Generated Computations. — a.

A copy of the output sheets for computer-generated computations shall be submitted as part of the design computations. i.

b.

Copyright 2010

The first sheet of the output sheets shall be signed and sealed by the designer.

The output sheets shall be accompanied by a certification of a designer and/or consultant that the output sheets are the results obtained through the use of documented programs. The certification should include the identification of the specific program used for each portion of the computer-generated computations being submitted. i.

The data provided, as computer input shall be clearly distinguished from those computed in the program.

ii.

The information required in the output shall include date of processing, program identification, all output data,

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

300

units and final results. RULE XX Signs SECTION 2001. General Requirements. — 1.

No sign or signboard shall be erected in such a manner as to confuse or obstruct the view or interpretation of any official traffic sign, signal, or device.

2.

Signs which are written in any foreign language shall have a corresponding translation in English or in the local dialect.

3.

The bottom line of all signboards adjacent to each other shall follow a common base line as determined by the Building Official.

4.

The installation of all kinds of signs shall be such that a harmonious and aesthetic relationship of all units therein is presented.

SECTION 2002. Maintenance. — All signs, together with all of their supports, braces, guys, and anchors, shall be kept in repair and in proper state of preservation. The display of all signs shall be kept neatly painted and secured at all times. SECTION 2003. Design and Construction. — Sign structures shall be designed and constructed to resist all forces in accordance with the National Structural Code for Buildings. For signs on buildings, the dead lateral loads shall be transmitted thorough the structural frame of the building to the ground in such a manner as not to overstress any of the elements of the building. The weight of earth superimposed over footings may be used in determining the dead load resisting moment. Such earth shall be carefully placed and thoroughly compacted. SECTION 2004. Supports and Anchorages. — 1.

Copyright 2010

General. The supports and anchorages of all signs or sign structures shall be placed in or upon private property and shall be constructed in conformity with the requirements of the Code.

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

301

a.

Sign structures may be constructed only in areas where zoning regulations permit them and in accordance with the accepted standards of design, construction and maintenance. CTDacA

b.

c.

Roof Signs i.

The design and construction of roof signs shall conform to the provisions of Sec. 1210 of the Code.

ii.

No signs shall be erected, attached to, installed or fastened on rooftops of buildings of wooden structures or of buildings/structures with wooden roof framing.

iii.

Adequate provisions for grounding metallic parts of roof signs exposed to lightning shall be provided.

iv.

Installation of warning lights/obstruction lights for air traffic shall be installed where applicable.

Ground Signs i.

Ground signs and advertising ground signs which shall be constructed in conformity with accepted engineering standards, of which height control shall be in conformity with the Local Zoning Regulation (LZR). (Figure XX.1.) IaDcTC

d.

ii.

Ground sign structures shall be located within the property line and under no circumstances shall they occupy the RROW/street or sidewalk/arcade or similar access-ways.

iii.

Public or government signs erected or installed within the area of the sidewalk shall be so designed and located that they do not obstruct the easy passage of pedestrians nor distract the attention of motorists.

Projecting Signs i.

Copyright 2010

CD Technologies Asia, Inc.

On non-arcaded RROW/streets, signs shall not extend more than 1.20 meters over the sidewalk and measured horizontally from the wall line or building line. On arcaded RROW/streets, the signs shall not project more Philippine Laws Premium Edition 2009

302

than 0.60 meter from the outermost portion of the wall line of the allowed structure over the arcade. For buildings abutting on RROW/streets or alleys without sidewalks or provisions therefor, the signs shall not project more than 0.30 meter from the outermost portion of the building/structure. (Figures XX.2., XX.3., and XX.4.) aEHADT

ii.

A height clearance of not less than 3.00 meters measured from the finished road surface shall be provided below the lowest part of such signs projecting over sidewalks on buildings without arcades and a clearance of not less than 5.00 meters shall be provided below the lowest part of such signs projecting over arcaded RROW/streets.

iii.

The erection of electric neon signboards or other advertisements of similar nature projecting over roadways or public streets shall be allowed, provided that: (1) Clear distance between the signboards erected on one building is not less than 4.00 meters. (2) Signboards on multi-storey buildings shall be erected on the same vertical line and shall not overlap each other. (3) Tops of signboards shall not extend over the topmost part of the parapet or the bottom line of the eave of the building. (4) Horizontal projections of signboards shall follow subsections (i) and (ii). of this Rule. (5) In case of two (2) adjacent buildings, adjacent signboards shall be placed at a distance of not less than 2.00 meters from the common boundary line. (6) Signboards shall not obstruct any window or emergency exit and shall not be closer than 1.00 meter from electric and telephone posts and wires.

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

303

e.

Wall Signs i.

Outdoor display signs placed against the front exterior surface of buildings shall not extend more than 300 millimeters from the wall with its lowest portion not less than 3.00 meters above the sidewalk.

ii.

Commercial signs shall not be attached to, painted on, installed or displayed on posts/columns, beams/girders or any other exterior portion of arcades and structures for public utilities/services, e.g. mass transit and the like. THacES

iii. 2.

Display windows or wall signs within 3.00 meters above the sidewalk shall be flushed or recessed.

Materials. Materials for construction of signs or sign structures shall be of the quality and grade as specified in the Code. In all signs and sign structures, the materials and details of construction shall, in the absence of specified requirements, conform to the following: a.

Structural steel shall be of such quality as to conform to ASTM A 36. Secondary members in contact with or directly supporting the display surface may be formed of light gauge steel, provided such members are designed in accordance with the specifications of the design of light gauge steel as specified in ASTM A 242 and, in addition, shall be galvanized. Secondary members, when formed integrally with the display surface, shall be not less than No. 24 gauge in thickness. When not formed integrally with the display surface, the minimum thickness of the secondary members shall be No. 12 gauge. The minimum thickness of hot-rolled steel members furnishing structural support for signs shall be 6.35 millimeters, except that if galvanized, such members shall be not less than 3.18 millimeters thick. Steel pipes shall be of such quality as to conform to ASTM A 36. Steel members may be connected with one galvanized bolt provided that connection is adequate to transfer the stresses in the members. STaCcA

b. Copyright 2010

Anchors and supports, when of wood and embedded in the soil, or within 150 millimeters of the soil, shall all be

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

304

of heartwood of a durable species or shall be pressure-treated with an approved preservative. 3.

Restrictions on Combustible Materials — All signs or sign structures erected in highly restrictive Fire Zones shall have structural members of incombustible materials. Ground signs may be constructed of any material meeting the requirements of the Code. Combination signs, roof signs, wall signs, projecting signs, and signs on marquees shall be constructed of incombustible materials. No combustible material other than approved plastics shall be used in the construction of electric signs.

4.

Non-structural Trim — Non-structural trim and portable display surfaces may be of wood, metal, approved plastics, or any combination thereof.

5.

Display Surfaces — Display surfaces in all types of signs may be made of metal, glass, or approved, plastics.

SECTION 2005. Projections and Clearances. —

Copyright 2010

1.

Clearances from High Voltage Power Lines — Clearances of signs from high voltage power lines shall be in accordance with the Philippine Electrical Code.

2.

Clearances from Fire Escapes, Exits, or Standpipes — No signs or sign structures shall be erected in such a manner than any portion of its surface or supports will interfere in any way with the free use of any fire escape, exit, or standpipe.

3.

Obstruction of Openings. No sign shall obstruct any opening to such an extent that light or ventilation is reduced to a point below that required by the Code. Signs erected within 1.50 meters of an exterior wall in which there are openings within the area of the sign shall be constructed of incombustible material or approved plastics.

4.

Projection over Alleys. No sign or sign structure shall project into any public alley below a height of 3.00 meters above established sidewalk grade, nor project more than 300 millimeters where the sign structure is located 3.00 meters to 4.50 meters above established sidewalk grade. The sign or sign

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

305

structure must not project more than 1.00 meter into the public alley where the sign or sign structure is located more than 4.50 meters above established sidewalk grade. CAHaST

SECTION 2006. Lighting. — Signs shall be illuminated only by electrical means in accordance with the Philippine Electrical Code.

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

306

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

307

PROJECTING SIGNS RULE XXI Final Provisions Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

308

SECTION 2101. Separability Clause. — If any provision of this IRR or the application thereof to any person or circumstance is declared unconstitutional or invalid by a competent court, the other sections and provisions hereof which are not affected thereby shall continue to be in full force and effect. SECTION 2102. Repealing and Amending Clause. — All Administrative Orders, rules and regulations, memoranda, circulars and other issuances inconsistent herewith or contrary to the provisions of these rules and regulations are hereby repealed or modified accordingly. SECTION 2103. Effectivity. — This IRR shall take effect fifteen (15) days after is publication once a week for three (3) consecutive weeks in a newspaper of general circulation. APPROVED this 29th of October, 2004.

(SGD.) FLORANTE SORIQUEZ Acting Secretary

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

309

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

310

NEW SCHEDULE OF FEES AND CHARGES 1.

2.

Bases of assessment a.

Character of occupancy or use of building/structure

b.

Cost of construction

c.

Floor area

d.

Height

cEHSIC

Regardless of the type of construction, the cost of construction of any building/structure for the purpose of assessing the corresponding fees shall be based on the following table: Table II.G.1. On Fixed Cost Of Construction Per Sq. Meter LOCATION All Cities and Municipalities

3.

GROUP A, B, C, D, E, G, H, I P10,000

F P8,000

J P6,000

Construction/addition/renovation/alteration of buildings/structures under Group/s and Sub-Divisions shall be assessed as follows: a.

Division A-1 Area in sq. meters

i. ii. iii. iv. v. vi.

Fee per sq. meter

Original complete construction up to 20.00 sq. meters Additional/renovation/alteration up to 20.00 sq. meters regardless of floor area of original construction Above 20.00 sq. meters to 50.00 sq. meters Above 50.00 sq. meters to 100.00 sq. meters Above 100.00 sq. m to 150 sq. meters Above 150.00 sq. meters

P2.00 2.40 3.40 4.80 6.00 7.20

Sample Computation for Building Fee for a 75.00 sq. meters floor area: Floor area = 75.00 sq. meters Therefore area bracket is 3.a.iv. Fee = P4.80/sq. meter Building Fee = 75.00 x 4.80 = P360.00 Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

311

b.

Division A-2 Area in sq. meters

i. ii. iii. iv. v.

c.

Original complete construction up to 20.00 sq. meters Additional/renovation/alteration up to 20.00 sq. meters regardless of floor area of original construction Above 20.00 sq. meter to 50.00 sq. meters Above 50.00 sq. meters to 100.00 sq. meters Above 150.00 sq. m to 150 sq. meters

P3.00 3.40 5.20 8.00 8.40

Divisions B-1/C-1/E-1, 2, 3/F-1/G-1, 2, 3, 4, 5/H-1, 2, 3, 4/I-1 and J-1, 2, 3 Area in sq. meters

i. ii. iii. iv. v. vi. vii. viii. ix. x.

Fee per sq. meter

Up to 500 Above 500 to 600 Above 600 to 700 Above 700 to 800 Above 800 to 900 Above 900 to 1,000 Above 1,000 to 1,500 Above 1,500 to 2,000 Above 2,000 to 3,000 Above 3,000

Fee per sq. meter P23.00 22.00 20.50 19.50 18.00 17.00 16.00 15.00 14.00 12.00

NOTE: Computation of the building fee for item 3.c. is cumulative. The total area is split up into sub-areas corresponding to the area bracket indicated in the Table above. Each sub-area and the fee corresponding to its area bracket are multiplied together. The building fee is the sum of the individual products as shown in the following example: Sample Computation for Building Fee for a building having a floor area of 3,200 sq. meters: First 500 sq. meters @ 23.00 Next 100 sq. meters @ 22.00 Next 100 sq. meters @ 20.50 Next 100 sq. meters @ 19.50 Next 100 sq. meters @ 18.00 Next 100 sq. meters @ 17.00 Next 100 sq. meters @ 16.00 Next 500 sq. meters @ 15.00 Next 1,000 sq. meters @ 14.00 Last 200 sq. meters @ 12.00

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

P11,500.00 2,200.00 2,050.00 1,950.00 1,800.00 1,700.00 8,000.00 7,500.00 14,000.00 2,400.00

312

Total Building Fee

d.

P53,100.00

Divisions C-2/D-1, 2, 3 Area in sq. meters

i. ii. iii. iv. v. vi. vii. viii. ix. x.

Fee per sq. meter

Up to 500 Above 500 to 600 Above 600 to 700 Above 700 to 800 Above 800 to 900 Above 900 to 1,000 Above 1,000 to 1,500 Above 1,500 to 2,000 Above 2,000 to 3,000 Above 3,000

P12.00 11.00 10.20 9.60 9.00 8.40 7.20 6.60 6.00 5.00

NOTE: Computation of the building fee in item 3.d. follows the example of Section 3.c. of this Schedule. e.

4.

Division J-2 structures shall be assessed 50% of the rate of the principal building of which they are accessories (Sections 3.a. to 3.d.).

Electrical Fees The following schedule shall be used for computing electrical fees in residential, institutional, commercial and industrial structures: a.

Total Connected Load (kVA) Fee

i. ii. iii. iv. v. vi.

5 kVA or less Over 5 kVA to 50 kVA Over 50 kVA to 300 kVA Over 300 kVA to 1,500 kVA Over 1,500 kVA to 6,000 kVA Over 6,000 kVA

P200.00 P200.00 1,100.00 3,600.00 9,600.00 20,850.00

+ + + + +

P20.00/kVA 10.00/kVA 5.00/kVA 2.50/kVA 1.25/kVA

NOTE: Total Connected Load as shown in the load schedule. b.

Total Transformer/Uninterrupted Power Supply (UPS)/Generator Capacity (kVA) Fee

i. Copyright 2010

5 kVA or less

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

P40.00 313

ii. iii. iv. v. vi.

Over 5 kVA to 50 kVA Over 50 kVA to 300 kVA Over 300 kVA to 1,500 kVA Over 1,500 kVA to 6,000 kVA Over 6,000 kVA

P40.00 220.00 720.00 1,920.00 4,170.00

+ + + + +

P4.00/kVA 2.00/kVA 1.00/kVA 0.50/kVA 0.25/kVA

NOTE Total Transformer/UPS/Generator Capacity shall include all transformer, UPS and generators which are owned/installed by the owner/applicant as shown in the electrical plans and specifications. CTSHDI

c.

Pole/Attachment Location Plan Permit i. ii.

Power Supply Pole Location Guying Attachment

P30.00/pole P30.00/attachment

This applies to designs/installations within the premises. d.

Miscellaneous Fees: Electric Meter for union separation, alteration, reconnection or relocation and issuance of Wiring Permit: Use or Character of Occupancy Residential Commercial/Industrial Institutional

e.

Electric Meter

P15.00 60.00 30.00

Wiring Permit Issuance P15.00 36.00 12.00

Formula for Computation of Fees

The Total Electrical Fees shall be the sum of Sections 4.a. to 4.d. of this Rule. TCAScE

f.

Forfeiture of Fees The electrical work or installation is found not in conformity with the minimum safety requirements of the Philippine Electrical Codes and the Electrical Engineering Law (RA 7920) and the Owner fails to perform corrective actions within the reasonable time provided by the Building Official, the latter and/or, their duly authorized representative shall forthwith cancel the permit and the fees thereon shall be forfeited.

5.

Mechanical Fees a.

Refrigeration, Air Conditioning and Mechanical Ventilation: i. ii.

Copyright 2010

CD Technologies Asia, Inc.

Refrigeration (cold storage), per ton or fraction thereof P40.00 Ice Plants, per ton or fraction thereof 60.00 Philippine Laws Premium Edition 2009

314

iii. iv. v. vi. vii.

Packaged/Centralized Air Conditioning Systems: Up to 100 tons, per ton 90.00 Every ton or fraction thereof above 100 tons 40.00 Window type air conditioners, per unit 60.00 Mechanical Ventilation, per kW or fraction thereof of blower or fan, or metric equivalent 40.00 In a series of AC/REF systems located in one establishment, the total installed tons of refrigeration shall be used as the basis of computation for purposes of installation/inspection fees, and shall not be considered individually.

For evaluation purposes: For Commercial/Industrial Refrigeration without Ice Making (refer to 5.a.i.): 1.10 kW per ton, for compressors up to 5 tons capacity. 1.00 W per ton, for compressors above 5 tons up to 50 tons capacity. 0.97 kW per ton, for compressors above 50 tons capacity. For Ice making (refer to 5.a.ii.): 3.50 kW per ton, for compressors up to 50 tons capacity. 3.25 kW per ton, for compressors above 5 up to 50 tons capacity. 3.00 kW per ton, for compressors above 50 tons capacity. For Air conditioning (refer to 5.a.iii.): 0.90 kW per ton, for compressors 1.2 to 5 tons capacity. 0.80 kW per ton, for above 5 up to 50 tons capacity. 0.70 kW per ton, for compressors above 50 tons capacity. b.

Escalators and Moving Walks, funiculars and the like: i. Escalator and moving walk, per kW or fraction thereof ii. Escalator and moving walks up to 20.00 lineal meters or fraction thereof iii. Every lineal meter or fraction thereof in excess of 20.00 lineal meters iv. Funicular, per kW or fraction thereof a) Per lineal meter travel v. Cable car, per kW or fraction thereof (a) Per lineal meter travel

c.

20.00 10.00 200.00 20.00 40.00 5.00

Elevators, per unit: i. ii.

Copyright 2010

P10.00

CD Technologies Asia, Inc.

Motor driven dumbwaiters Construction elevators for material Philippine Laws Premium Edition 2009

P600.00 2,000.00 315

iii. iv. v. d.

Passenger elevators Freight elevators Car elevators

5,000.00 5,000.00 5,000.00

Boilers, per kW: i. ii. iii. iv. v. vi. vii.

Up to 7.5 kW Above 7.5 kW to 22 kW Above 22 kW to 37 kW Above 37 kW to 52 kW Above 52 kW to 67 kW Above 67 kW to 74 kW Every kW or fraction thereof above 74 kW

P500.00 700.00 900.00 1,200.00 1,400.00 1,600.00 5.00

NOTE: (a) Boiler rating shall be computed on the basis of 1.00 sq. meter of heating surface for one (1) boiler kW. (b) Steam from this boiler used to propel any prime-mover is exempted from fees. (c) Steam engines/turbines/etc. propelled from geothermal source will use the same schedule of fees above. e.

Pressurized water heaters, per unit

f.

Water, sump and sewage pumps for commercial/industrial use, per kW or fraction thereof 60.00

g.

Automatic fire sprinkler system, per sprinkler head

h.

Diesel/Gasoline ICE, Steam, Gas Turbine/Engine, Hydro, Nuclear or solar Generating Units and the like, per kW: i. ii. iii.

i.

j.

k.

Copyright 2010

Every kW up to 50 kW Above 50 kW up to 100 kW Every kW above 100 kW

Compressed Air, Vacuum, Commercial, Institutional and/or Industrial Gases, per outlet Power piping for gas/steam/etc., per lineal meter or fraction thereof or per cu. meter or fraction thereof whichever is higher

P200.00

4.00

P25.00 20.00 3.00

P20.00

P4.00

Other Internal Combustion Engines, including cranes, forklifts, loaders, pumps, mixers, compressors and the like, not registered with the LTO, per kW:

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

316

i. ii. iii.

Up to 50 kW Above 50 kW to 100 kW Every above 100 kW or fraction thereof

P10.00 12.00 3.00

l.

Pressure Vessels, per cu. meter or fraction thereof

P60.00

m.

Other Machinery/Equipment for Commercial/ Industrial/Institutional Use not elsewhere specified, per kW or fraction thereof

P60.00

Pneumatic tubes, Conveyors, Monorails for materials handling and addition to existing supply and/or exhaust duct works and the like, per lineal meter or fraction thereof

P10.00

n.

NOTE: Transfer of machine/equipment location within a building requires a mechanical permit and payment of fees. 6.

Plumbing Fees a.

Installation Fees, one (1) "UNIT" composed of one (1) water closet, two (2) floor drains, one (1) lavatory, one (1) sink with ordinary trap three (3) faucets and one (1) shower head. A partial part thereof shall be charged as that of the cost of a whole "UNIT".

b.

Every fixture in excess of one unit: i. ii. iii. iv. v. vi.

c.

P7.00 3.00 3.00 7.00 2.00 2.00

Special Plumbing Fixtures: i. ii. iii. iv. v. vi. vii. viii. ix. x. xi. xii.

Copyright 2010

Each water closet Each floor drain Each sink Each lavatory Each faucet Each shower head

CD Technologies Asia, Inc.

Each slop sink Each urinal Each bath tub Each grease trap Each garage trap Each bidet Each dental cuspidor Each gas-fired water heater Each drinking fountain Each bar or soda fountain sink Each laundry sink Each laboratory sink Philippine Laws Premium Edition 2009

P7.00 4.00 7.00 7.00 7.00 4.00 4.00 4.00 2.00 4.00 4.00 4.00 317

xiii. Each fixed-type sterilizer

d.

e.

Each water meter

P2.00

i. ii.

P8.00 10.00

Copyright 2010

12 to 25 mm Above 25 mm

Construction of septic tank, applicable in all Groups i. ii.

7.

2.00

Up to 5.00 cu. meters of digestion chamber Every cu. meter or fraction thereof in excess of 5.00 cu. meters

P24.00 7.00

Electronics Fees a.

Central Office switching equipment, remote switching units, concentrators, PABX/PBX's, cordless/wireless telephone and communication systems, intercommunication system and other types of switching/routing/distribution equipment used for voice, data image text, facsimile, internet service, cellular, paging and other types/forms of wired or wireless communications P2.40 per port

b.

Broadcast station for radio and TV for both commercial and training purposes, CAN headed, transmitting/receiving/relay radio and broadcasting communications stations, communications centers, switching centers, control centers, operation and/or maintenance centers, other similar locations equipment silos/shelters and other similar locations/structures used for electronics and communications services, including those used for navigational aids, radar, telemetry, tests and measurements, global positioning and personnel/vehicle location P1,00000 per location

c.

Automated teller machines ticketing vending and other types of electronic dispensing machines, telephone booths, pay phones, coin changers, location or direction-finding systems, navigational equipment used for land, aeronautical or maritime applications, photography and reproduction machines x-ray, scanners, ultrasound and other apparatus/equipment used for medical, biomedical, laboratory and testing purposes and other similar electronic or electronically-controlled apparatus or devices,

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

318

whether located indoor or outdoors d.

Electronics and communications outlets used for connection and termination of voice, data, computer (including workstations, servers, routers, etc.), audio, video, or any form of electronics and communications services, irrespective of whether a user terminal is connected P2.40 per outlet

e.

Station/terminal/control point/port/central or remote panels/outlets for security and alarm systems (including watchman system, burglar alarms, intrusion detection systems, lighting controls, monitoring and surveillance system, sensors, detectors, parking management system, barrier controls, signal lights, etc.), electronics fire alarm (including early-detection systems, smoke detectors, etc.), sound-reinforcement/background, music/paging/conference systems and the like, CATV/MAAV/CCTV and off-air television, electronically-controlled conveyance systems, building automation, management systems and similar types of electronic or electronically-controlled installations whether a user terminal is connected P2.40 per termination

f.

Studios, auditoriums, theaters, and similar structures for radio and TV broadcast, recording, audio/video reproduction/simulation and similar activities

g.

h.

i.

Antenna towers/masts or other structures for installation of any electronic and/or communications transmission/reception

Electronic or electronically-controlled indoor and outdoor signages and display systems, including TV monitors, multi-media signs, etc.

P1 000.00 per location

P1,000.00 per structure

P50.00 per unit

Poles and attachment: i. ii.

Copyright 2010

P10.00 per unit

CD Technologies Asia, Inc.

Per Pole (to be paid by pole owner) Per attachment (to be paid by an entity who attaches to the pole of others) Philippine Laws Premium Edition 2009

P20.00 20.00 319

j.

8.

Other types or electronics or electronicallycontrolled device, apparatus, equipment, instrument or units not specifically identified above P50.00 per unit

Accessories of the Building/Structure Fees a.

All parts of buildings which are open on two (2) or more sides, such as balconies, terraces, lanais and the like, shall be charged 50% of the rate of the principal building of which they are a part (Sections 3.a. to 3.d. of this Schedule).

b.

Buildings with a height of more than 8.00 meters shall be charged an additional fee of twenty-five centavos (P0.25) per cu. meter above 8.00 meters. The height shall be measured from the ground level up to the bottom of the roof slab or the top of gins, whichever applies.

c.

Bank and Records Vaults with interior volume up to 20.00 cu. meters i.

d.

e.

In excess of 20.00 cu. meters

8.00

Swimming Pools, per cu. meter or fraction thereof: i.

GROUP A Residential

P3.00

ii.

Commercial/Industrial GROUPS B, E, F, G

36.00

iii.

Social/Recreational/Institutional GROUPS C, D, H, I24.00

iv.

Swimming pools improvised from local indigenous materials such as rocks, stones and/or small boulders and with plain cement flooring shall be charged 50% of the above rates.

v.

Swimming pool shower rooms/locker rooms: (a) Per unit or fraction thereof (b) Residential GROUP A (c) GROUP B, E, F, G (d) GROUP C, D, H

P60.00 6.00 18.00 12.00

Construction of firewalls separate from the building: i. ii.

Copyright 2010

P20.00

CD Technologies Asia, Inc.

Per sq. meter or fraction thereof Provided, that the minimum fee shall be Philippine Laws Premium Edition 2009

P3.00 48.00 320

f.

Construction/erection of towers: Including Radio and TV towers, water tank supporting structures and the like: Use or character of Occupancy Support i.

Self-Supporting

Trilon (Guyed

P500.00

P150.00

2,400.00

240.00

120.00

12.00

1,800.00

120.00

120.00

12.00

Single detached dwelling units

ii. Commercial/Industrial (Groups B, E, F, G) up to 10.00 meters in height (a) Every meter or fraction thereof in excess of 10.00 meters iii. Educational/Recreational//Institutional (Groups C, D, H, I) up to 10.00 meters in height (a) Every meter or fraction thereof in excess of 10.00 meters

g.

Storage Silos, up to 10.00 meters in height i. ii.

h.

ii.

j.

k. Copyright 2010

Every meter or fraction thereof in excess of 10.00 meters Silos with platforms or floors shall be charged an additional fee in accordance with Section 3.e. of this Schedule

P150.00

Construction of Smokestacks and Chimneys Commercial/Industrial Use Groups B, E, F and G: i.

i.

P2,400.00

Smokestacks, up to 10.00 meters in height, measured from the base (a) Every meter or fraction thereof in excess of 10.00 meters Chimney up to 10.00 meters in height, measured from the base (a) Every meter or fraction thereof in excess of 10.00 meters

Construction of Commercial/Industrial Fixed Ovens, per sq. meters or fraction thereof of interior floor areas Construction of Industrial Kiln/Furnace, per cu. meter or fraction thereof of volume

for

P240.00 12.00 48.00 2.00

P48.00

12.00

Construction of reinforced concrete or steel tanks or

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

321

above ground GROUPS A and B, up to 2.00 cu. meters i. ii.

l.

m.

Every cu. m or fraction thereof in excess of 2.00 cu. meters For all other than Groups A and B up to 10.00 cu. meters (a) Every cu. meter or fraction thereof in excess of 10.00 cu. meters

Construction of Water and Waste Water Treatment Tanks: (including Cisterns, Sedimentation and Chemical Treatment Tanks) per cu. meter of volume

ii. iii.

P7.00

P480.00 480.00 540.00 24.00

Underground, per cu. meter or fraction thereof of excavation P3.00 Saddle or trestle mounted horizontal tanks, per cu. meter or fraction thereof of volume of tank 3.00 Reinstallation of vertical storage tanks shall be the same as new construction fees in accordance with Section 8.k. above.

Construction of permanent type P10.00 Construction of temporary type 5.00 Inspection of knock-down temporary type, per unit 24.00

Construction of buildings and other accessory structures within cemeteries and memorial parks: i. ii. iii.

Copyright 2010

24.00

Boths, Kiosks, Platforms, Stages and the like, pr sq. meter or fraction thereof of floor area: i. ii. iii.

p.

480.00

Pull-outs and Reinstallation of Commercial/Industrial Steel Tanks: i.

o.

P12.00

Construction of reinforced concrete or steel tanks except for Commercial/Industrial Use: Above ground, up to 10.00 cu. meters Every cu. m or fraction thereof in excess of 10.00 cu. meters Underground, up to 20.00 cu. meters Every cu. meter or fraction thereof in excess of 20.00 cu. meters

n.

12.00

CD Technologies Asia, Inc.

Tombs, per sq. meter of covered ground Semi-enclosed mausoleums whether canopied or not, per sq. meter of built-up area Totally enclosed mausoleums, per sq. meter of Philippine Laws Premium Edition 2009

P5.00 5.00 322

iv. v. 9.

floor area Totally enclosed mausoleums, per sq. meter of floor area Columbarium, per sq. meter

5.00 18.00

Accessory Fees a.

Establishment of Line and Grade, all sides fronting or abutting streets, esteros, rivers and creeks, first 10.00 meters i.

b.

Every meter or fraction thereof in excess of 10.00 meters

2.40

While the application for Building Permit is still being processed, the Building Official may issue Ground Preparation and Excavation Permit (GP & EP) for foundation, subject to the verification, inspection and review by the Line and Grade Section of the Inspection and Enforcement Division to determine compliance to line and grade, setbacks, yards/easements and parking requirements. (a) (b) (c)

(d) (e) (f)

c.

P24.00

Ground Preparation and Excavation Fee i.

Inspection and Verification Fee P200.00 Per cu. meters of excavation 3.00 Issuance of GP & EP, valid only for thirty (30) days or superseded upon issuance of Building Permit 50.00 Per cu. meter of excavation for foundation with basement 4.00 Excavation other than foundation or basement, per cu. meter 3.00 Encroachment of footings or foundations of buildings/structures to public areas as permitted, per sq. meter or fraction thereof of footing or foundation encroachment 250.00

Fencing Fees: i.

Copyright 2010

12.00

CD Technologies Asia, Inc.

Made of masonry, metal, concrete up to 1.80 meters in height, per lineal meter or fraction thereof Philippine Laws Premium Edition 2009

P3.00 323

ii. iii.

In excess of 1.80 meters in height, per lineal meter or fraction thereof Made of indigenous materials, barbed, chicken or hog wires, per linear meter

2.40

d.

Construction of Pavements, up to 20.00 sq. meters

e.

In excess of 20% or fraction thereof of paved areas intended for commercial/industrial/institutional use, such as parking and sidewalk areas, gasoline station premises, skating rinks, pelota courts, tennis and basketball courts and the like

f.

g.

Every sq. meter or fraction thereof in excess of 20.00 sq. meters

P3.00

P240.00

P12.00

Erection of Scaffoldings Occupying Public Areas, per calendar month. i. ii.

h.

P24.00

Use of Streets and Sidewalks, Enclosures and Occupancy of Sidewalks up to 20.00 sq. meters, per calendar month i.

Up to 10.00 meters in length Every lineal meter or fraction thereof in excess of 10.00 meters

P150.00 12.00

Sign Fees: i.

ii.

iii.

Erection and anchorage of display surface, up to 4.00 sq. meters of signboard area P120.00 (a) Every sq. meter or fraction thereof in excess of 4.00 sq. meters 24.00 Installation Fees, per sq. meter or fraction thereof of display surface: Type of Sign Display

Business Signs

Advertising Signs

Neon Illuminated Others Painted-on

P36.00 24.00 15.00 9.60

P52.00 36.00 24.00 18.00

Annual Renewal Fees, per sq. meter of display surface or fraction thereof:

Type of Sign Display Copyright 2010

4.00

CD Technologies Asia, Inc.

Business Signs

Philippine Laws Premium Edition 2009

Advertising Signs 324

i.

Neon

P36.00, min. fee shall be P124.00

P46.00, min. fee shall be P200.00

Illuminated

P18.00, min. fee shall be P72.00

P38.00, min. fee shall be P150.00

Others

P12.00, min. fee shall be P40.00

P20.00, min. fee shall be P110.00

Painted-on

P8.00, min. fee shall be P30.00

P12.00, min. fee shall be P100.00

Repairs Fees: i.

ii.

iii.

j.

k.

P5.00

5.00

Raising of Buildings/Structures Fees: i.

Assessment of fees for raising of any buildings/structures shall be based on the new usable area generated.

ii.

The fees to be charged shall be as prescribed under Sections 3.a. to 3.e. of this Schedule, whichever Group applies.

Demolition/Moving of Buildings/Structures Fees, per sq. meter of area or dimensions involved: i. ii.

Copyright 2010

Alteration/renovation/improvement on vertical dimensions of buildings/structures in square meter, such as facades, exterior and interior walls, shall be assessed in accordance with the following rate, For all Groups Alteration/renovation/improvement on horizontal dimensions of buildings/structures, such as floorings, ceilings and roofing shall be assessed in accordance with the following rate, For all Groups Repairs on buildings/structures in all Groups costing more than five thousand pesos (P5,000.00) shall be charged 1% of the detailed repair cost (itemized original materials to be replaced with same or new substitute and labor)

CD Technologies Asia, Inc.

Buildings in all Groups per sq. meter floor area Building Systems/Frames or portion Philippine Laws Premium Edition 2009

P3.00

325

iii.

iv.

v.

10.

4.00 800.00 50.00 50.00 50.00 3.00

Certificates of Use or Occupancy (Table II.G.1. for fixed costing) a.

Division A-1 and A-2 Buildings: i. ii. iii. iv. v.

b.

iii. iv. v.

c.

Costing up to P150,000.00 Costing more than P150,000.00 up to P400,000.00 Costing more than P400,000.00 up to P850,000.00 Cost in more than P850,000.00 up to P1,200,000.00 Every million or portion thereof in excess of P1,200,000.00

P100.00 200.00 400.00 800.00 800.00

Divisions B-1/E-1, 2, 3/F-1/G-1, 2, 3, 4, 5/H-1, 2, 3, 4/and I-1 Buildings: i. ii.

Costing up to P150,000.00 Costing more than P150,000.00 up to P400,000.00 Costing more than P400,000.00 up to P850;000.00 Costing more than P850,000.00 up to P1,200,000.00 Every million or portion thereof in excess of P1,200,000.00

P200.00 400.00 800.00 1,000.00 1,000.00

Divisions C-1, 2/D-1, 2, 3 Buildings: i. ii. iii. iv.

Copyright 2010

thereof per vertical or horizontal dimensions, including Fences Structures of up to 10.00 meters in height (a) Every meter or portion thereof in excess of 10.00 meters Appendage of up to 3.00 cu. meter/unit (a) Every cu. meter or portion thereof in excess of 3.00 cu. meters Moving Fee, per sq. meter of area of building/structure to be moved

CD Technologies Asia, Inc.

Costing up to P150,000.00 Costing more than P150,000.00 up to P400,000.00 Costing more than P400,000.00 up to P850,000.00 Costing more than P850,000.00 Philippine Laws Premium Edition 2009

P150.00 250.00 600.00

326

v.

d.

iii. iv. v.

With floor area up to 20.00 sq. meters With floor area above 20.00 sq. meters up to 500.00 sq. meters With floor area above 500.00 sq. meters up to 1,000.00 sq. meters With floor area above 1,000.00 sq. meters up to 5,000.00 sq. meters With floor area above 5,000.00 sq. meters up to 10,000.00 sq. meters With floor area above 10,000.00 sq. meters

240.00 360.00 480.00 200.00 2,400.00

Garages, carports, balconies, terraces, lanais and the like: 50% of the rate of the principal building, of which they are accessories.

ii.

Aviaries, aquariums, zoo structures and the like: same rates as for Section 10.d. above.

iii.

Towers such as for Radio and TV transmissions, cell site, sign (ground or roof type) and water tank supporting structures and the like in any location shall be imposed fees as follows: First 10.00 meters of height from the ground Every meter or fraction thereof in excess of 10.00 meters

P800.00 50.00

Change in Use/Occupancy, per sq. meter or fraction thereof of area affected P5.00

Annual Inspection Fees a.

Copyright 2010

P50.00

i.

(b)

11.

900.00

Division J-2 Structures:

(a)

f.

900.00

Division J-I Buildings/structures: i. ii.

e.

up to 1,200,000.00 Every million or portion thereof in excess of P1,200,000.00

Divisions A-1 and A-2: i.

Single detached dwelling units and duplexes are not subject to annual inspections.

ii.

If the owner request inspections, the fee for each

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

327

of the services enumerated below is Land Use Conformity Architectural Presentability Structural Stability Sanitary and Health Requirements Fire-Resistive Requirements b.

Divisions B-1/D-1, 2, 3/E-1, 2, 3/F-1/G-1, 2, 3, 4 5/ H-1, 2, 3, 4/ and I-1, Commercial, Industrial Institutional buildings and appendages shall be assessed area as follows: i. ii. iii.

Appendage of up to 3.00 cu. meters/unit Floor area to 100.00 sq. meters Above 100.00 sq. meters up to 200.00 sq. meters iv. Above 200.00 sq. meters up to 350.00 sq. meters v. Above three hundred 350.00 sq. meters Up to 500.00 sq. meters vi. Above 500.00 sq. meters up to 750.00 sq. meters vii. Above 750.00 sq. meters up to 1,000.00 sq. meters viii. Every 1,000.00 sq. meters or its portion in excess of 1,000.00 sq. meters c.

Copyright 2010

P150.00 120.00 240.00 80.00 720.00 960.00 1,200.00

1,200.00

Divisions C-1, 2, Amusement Houses, Gymnasia and the like: i. ii. iii. iv.

First class cinematographs or theaters P1,200.00 Second class cinematographs or theaters 720.00 Third class cinematographs or theaters 520.00 Grandstands/Bleachers, Gymnasia and the like 720.00

d.

Annual plumbing Inspection fees, each plumbing unit

e.

Electrical Inspection Fees:

f.

P120.00

P60.00

i.

A one time electrical inspection fee equivalent to 10% of Total Electrical Permit Fees shall be charged to cover all inspection trips during construction.

ii.

Annual Inspection Fees are the same as in Section 4.e.

Annual Mechanical Inspection Fees:

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

328

i.

Refrigeration and Ice Plant, per ton: a) b) c) d) e)

ii.

Up to 100 tons capacity P25.00 Above 100 tons up to 150 tons 20.00 Above 150 tons up to 300 tons 15.00 Above 300 tons up to 500 tons 10.00 Every ton or fraction thereof above 500 tons 5.00

Air-Conditioning Systems: Window-type air conditioners, per unit

iii.

Packaged or centralized air conditioning systems: (a) (b) (c)

iv.

CD Technologies Asia, Inc.

Escalator and Moving Walks, per unit P120.00 Funiculars, per kW or fraction thereof 50.00 Per lineal meter or fraction thereof of travel 10.00 Cable Car, per kW or fraction thereof 25.00 Per lineal meter of travel 2.00

Passenger elevators Freight elevators Motor driven dumbwaiters Construction elevators for materials Car elevators Every landing above first five (5) landings for all the above elevators

P500.00 400.00 50.00 400.00 500.00 50.00

Boilers, per unit: (a) (b) (c)

Copyright 2010

P10.00 50.00 20.00

Elevators, per unit: (a) (b) (c) (d) (e) (f)

vii.

Up to 1 kW Above 1 kW to 7.5 kW Every kW above 7.5 kW

Escalators and Moving Walks; Funiculars and the like: (a) (b) (c) (d) (e)

vi.

First 100 tons, per ton P25.00 Above 100 tons. up to 150 tons per ton 20.00 Every ton or fraction thereof above 500 tons 8.00

Mechanical Ventilation, per unit, per kW: (a) (b) (c)

v.

P40.00

Up to 7.5 kW 7.5 kW up to 22 kW 22 kW up to 37 kW

Philippine Laws Premium Edition 2009

P400.00 550.00 600.00 329

(d) (e) (f) (g)

37 kW up to 52 kW 650.00 52 kW up to 67 kW 800.00 67 kW up to 74 kW 900.00 Every kW or fraction thereof above 74 kW 4.00

viii. Pressurized Water Heaters, per unit ix.

x.

xi.

Automatic Fire Extinguishers, per sprinkler head Water, Sump and Sewage pumps for buildings/structures for commercial/industrial purposes, per kW: a) Up to 5 kW b) Above 5 kW to 10 kW c) Every kW or fraction thereof above 10 kW

P2.00

P55.00 90.00 2.00

Diesel/Gasoline Internal Combustion Engine, Gas Turbine/Engine, Hydro, Nuclear or Solar Generating Units and the like, per kW: (a) (b) (c)

Per kW, up to 50 kW Above 50 kW up to 100 kW Every kW or fraction thereof above 100 kW

xii. Compressed air, vacuum, commercial/institutional/industrial gases, per outlet

P15.00 10.00 2.40

P10.00

xiii. Power piping for gas/steam/etc., per lineal meter or fraction thereof or per cu. meter or fraction thereof, whichever is higher

P2.00

xiv. Other Internal Combustion Engines, including Cranes, Forklifts, Loaders, Mixers, Compressors and the like, (a) Per unit, up to 10 kW (b) Every kW above 10 kW

100.00 3.00

xv. Other machineries and/or equipment for commercial/ industrial/institutional use not elsewhere specified, per unit: a) Up to 1/2 kW Copyright 2010

P120.00

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

P8.00 330

b) c) d) e) f)

Above 1/2 kW up to 1 kW Above 1 kW up to 3 kW Above 3 kW up to 5 kW Above 5 kW up to 10 kW Every kW above 10 kW or fraction thereof

23.00 39.00 55.00 80.00 4.00

xvi. Pressure Vessels, per cu. meter or fraction thereof P40.00 xvii. Pneumatic tubes, Conveyors, Monorails for materials handling, per lineal meter or fraction thereof xviii. Weighing Scale Structure, per ton or fraction thereof xix. Testing/Calibration of pressure gauge, per unit (a) Each Gas Meter, tested, proved and sealed, per gas meter xx. Every mechanical ride inspection, etc., used in amusement centers of fairs, such as ferris wheel, and the like, per unit g.

12.

P2.40

P30.00 P24.00 30.00

P30.00

Annual electronics inspection fees shall be the same as the fees in Section 7. of this Schedule.

Certifications: a. b. c. d. e. f. g. h.

Certified true copy of building permit Certified true copy of Certificate of Use/Occupancy Issuance of Certificate of Damage Certified true copy of Certificate of Damage Certified true copy of Electrical Certificate Issuance of Certificate of Gas Meter Installation Certified true copy of Certificate of Operation Other Certifications

P50.00 50.00 50.00 50.00 50.00 50.00 50.00 50.00

NOTE: The specifications of the Gas Meter shall be: Manufacturer Serial Number Gas Type Meter Classification/Model Maximum Allowable Operating Pressure — psi (kPa) Hub Size — mm (inch) Capacity — m3/hr. (ft3/hr.) Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

331

Page Compositor: Diana Keyser Punzalan

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

332

Endnotes 1 (Popup - Popup) BP 220

BP 344 PD 856 PD 1067 PD 1096 PD 1185 RA 386 RA 1364 RA 1378 RA 4566 RA 5336 RA 7920 RA 8495 Revised National Plumbing Code of the Philippines

Copyright 2010

CD Technologies Asia, Inc.

Philippine Laws Premium Edition 2009

333

View more...

Comments

Copyright © 2017 KUPDF Inc.
SUPPORT KUPDF Sitemap